00197498-03_UM_SiplaceCA-Serie_EN - 第331页
User Manual SIPLACE CA-Series 5 Setting up and Commissioning From software version SC.708.0 Editi on 12/2014 EN -DRAFT 5.6 Fitting the SWS 331 5 5 5.6.2 T ools and Equipment Y ou will need the following tools a nd equipm…
5 Setting up and Commissioning User Manual SIPLACE CA-Series
5.6 Fitting the SWS From software version SC.708.0 Edition 12/2014 EN -DRAFT
330
5.6 Fitting the SWS
5
5.6.1 Warning Instructions
5
5
5
5
CAUTION
Before installing the SWS, make sure that the placement machine has been completely
assembled. (See section 5.5
)
WARNING
Observe the applicable accident prevention regulations!
Only ASM engineers or qualified people are permitted to set up and commission the place-
ment machine.
Always follow the applicable accident prevention regulations.
WARNING
Risk of injury during assembly work to the underside of the SWS!
All assemblies and parts can be fitted from above. There is a risk of injury during assembly
work to the underside of the machine.
During assembly or installation never lie down under the SWS.
Secure the SWS using suitable measures. The fork-lift must not be used as the only
support.
WARNING
Risk of injury during assembly work!
Incorrect positioning of gantries during assembly restricts the head clearance and could
lead to injuries.
Take care that the gantries are positioned over the board conveyor area.
WARNING
Adjusting the height of the SWS!
Two people will be needed to adjust the height of the SWS:
– One person completes the required assembly work
– The other person watches the stability of the raised SWS during assembly.
User Manual SIPLACE CA-Series 5 Setting up and Commissioning
From software version SC.708.0 Edition 12/2014 EN -DRAFT 5.6 Fitting the SWS
331
5
5
5.6.2 Tools and Equipment
You will need the following tools and equipment to install the SWS:
– Standard tool
– Torque wrench
– Fork lift/hand lift (see section 5.3
), blocks for underneath if required
– Screwed feet
5.6.3 Installing the SWS in the Placement Machine
5.6.3.1 Positioning the Fork Lift
Position the fork-lift truck lengthwise under the SWS and open the forks until the contact sur-
faces of the SWS lie evenly on the forks. The magazine lift unit must be facing the forklift.
5
5
WARNING
DANGER OF CRUSHING!
Risk of crushing feet when transporting the SWS.
Wear specially reinforced shoes.
PLEASE NOTE
Please note that the SWS can only be fitted as follows:
– CA4 placement machine all locations (on the left-hand side for 1 and 3, on the right-
hand side for 2 and 4)
WARNING
Please note the following points before you raise the SWS, in order to avoid irrevers-
ible damage to the machine.
WARNING
Risk of damage due to one-sided loading!
One/sided loading of the machine feet e.g. from tilting the SWS, could lead to deformation
of the machine feet.
Make sure that the forks are evenly loaded when you lift the machine.
Use a firm support layer between the forks and the machine.
Enlist the help of a second person to watch while you lift the SWS and make sure that
the SWS does not tip over to one side.
5 Setting up and Commissioning User Manual SIPLACE CA-Series
5.6 Fitting the SWS From software version SC.708.0 Edition 12/2014 EN -DRAFT
332
5.6.3.2 Moving the SWS into the Placement Machine
5
5
Fig. 5.6 - 1 Connections on the SWS
5
5
Push the fork of the fork lift truck under the SWS (see section 5.2.4.3 on page 262).
Lift the SWS and align it to the placement machine. If the lifting range of the hand lift is not
sufficient, use wooden blocks or a similar object.
PLEASE NOTE
Before inserting the SWS, make sure that the CAN Bus connection X1x5 and X1x6,
the compressed air connection and the FFI communication interface W11 on the
SWS are accessible.
(1) Manometer for compressed air supply (2) Voltage supply
(3) Communication with SIPLACE machine (4) CAN bus
(5) Compressed air connection (modified
adapter dummy connector [03011592-01])
(6) LAN1
(7) LAN2
2
1
3
4
5
6
7