00197498-03_UM_SiplaceCA-Serie_EN - 第366页

6 Working with the Machine User Manual SIPLACE CA-Series 6.6 Performing a Sight Check From software version SC.708.0 Edition 12/2014 EN -DR AFT 366 6.6.3 Checking the PCB Support s  Check the position of the magnetic PC…

100%1 / 518
User Manual SIPLACE CA-Series 6 Working with the Machine
From software version SC.708.0 Edition 12/2014 EN -DRAFT 6.6 Performing a Sight Check
365
6
Check the multicolor status display (item 3 in fig. 6.6 - 1).
– If it lights up green, the feeder module is on standby.
– If it lights up orange, it is signaling a warning. The text of the warning appears on the LCD
display (item 4 in fig. 6.6 - 1
).
– If the status display lights up red, a malfunction has occurred. The error message
appears on the LCD display (item 3 in fig. 6.6 - 1
).
A list of the LCD and status displays on the operator panel is given in section 6.9
, page
379
. 6
If the status display is off, the cause may be as follows: 6
– The feeder module is not in the current setup.
– The feeder module is defective.
– The feeder module has been disabled (due to a drop in pressure, for example)
6.6.2 Splicing the Tapes in Good Time
6
6
CAUTION
Problems with cover foil withdrawal!
If the cover foil tears, this could lead to problems with the cover foil withdrawal.
There is an integral blade (item 2) for easily cutting the on the 8 and 12 mm X tape feeder
modules.
PLEASE NOTE
Late splicing of tapes
Late splicing of tapes could lead to prolonged down times..
Splice the tapes early enough so that the feeder modules do not run out of compo-
nents.
PLEASE NOTE
Early splicing of tapes
Early splicing of tapes can have the following consequence: when the old tape is rolled
up onto the new reel, the new reel could become too full and the tape will slide off it and
get caught up. This will again result in pick-up errors and prolonged down times.
Splice the tapes at the right time so that the old and new tapes do not get caught.
6 Working with the Machine User Manual SIPLACE CA-Series
6.6 Performing a Sight Check From software version SC.708.0 Edition 12/2014 EN -DRAFT
366
6.6.3 Checking the PCB Supports
Check the position of the magnetic PCB supports on the lifting table:
– Make sure that the PCB supports do not collide with components on the underside of the
PCBs.
– In addition, make sure that the PCB supports do not collide with the PCB conveyor pan-
els.
– Only use PCB supports as described in section 8.11
, page 494.
6.6.4 Mount for additional tape reel (X-Series)
6
Fig. 6.6 - 2 Mount for additional tape reel (X-Series)
(1) Mount for additional tape reel [00141217-xx]
(2) Mounting device for the support
6
Max. 60 mm
User Manual SIPLACE CA-Series 6 Working with the Machine
From software version SC.708.0 Edition 12/2014 EN -DRAFT 6.6 Performing a Sight Check
367
X-Series feeder modules can process component tapes without problems if the lateral offset be-
tween the feeder module and the tape reel does not exceed 60 mm. If a predefined setup means
that the maximum permitted offset cannot be maintained, we recommend that you use the mount
for an additional tape reel (item 1). Simply insert the mount into the holder (item 2) and push it until
the offset is less than the maximum permitted value of 60 mm. The component trolley has 5 hold-
ers in total. Each tape reel mount can hold 2 tape reels, which means that up to ten 15" (381 mm)
reels can be positioned above the tape container.