00197498-03_UM_SiplaceCA-Serie_EN - 第372页
6 Working with the Machine User Manual SIPLACE CA-Series 6.7 Configuring the Feeder Modules From software version SC.708.0 Edition 12/2014 EN -DR AFT 372 Remove any loos e compon ents from beneat h the pick-u p window …
User Manual SIPLACE CA-Series 6 Working with the Machine
From software version SC.708.0 Edition 12/2014 EN -DRAFT 6.7 Configuring the Feeder Modules
371
On standby, the status display (item 2 in fig. 6.7 - 1) lights up green if the X axis feeder
module is contained in the current setup. If the feeder module is not contained in the current setup,
the status display remains off.
The X feeder module is locked in position in the changeover table by a latch, and cannot be pulled
out. The procedure for removing feeder modules from the changeover table is as follows:
Press the removal handle (item 1 in fig. 6.7 - 1). The removal handle jumps out and the
status display goes out.
Wait approximately 1 second until the lock (item 4 in fig. 6.7 - 1) releases the feeder mod-
ule.
Use the removal handle to pull the feeder module out of the changeover table. If you wait
longer than 5 seconds, the feeder module will be locked once more. The status display
lights up red and the message (item 3 in fig. 6.7 - 1
) on the LCD display will be "Handle
--->>".
Engage the removal handle once more. If the X feeder module is contained in the current
setup, the status display lights up green and the track number and increment are appear
on the LCD display once more.
Press the removal handle again (item 1 in fig. 6.7 - 1) and now pull the feeder
module out of the changeover table.
6.7.3 Using the X Feeder Module on the Component Trolley (X-Series)
6.7.3.1 Checking the X Feeder Module Before Use
Check the following points before you use a feeder module on the changeover table:
The feeder module must be in perfect condition.
Tap the cover foil rocker (item 2 in fig. 6.7 - 2) to make sure that it does not stick.
Check that the area around the pickup window (item 3 in fig. 6.7 - 2) is free from loose
components.
6
Press the lever (item 4 in fig. 6.7 - 2) forward slightly to open the pickup window (item 3
in fig. 6.7 - 2
). This will raise the pick-up window slightly.
6
PLEASE NOTE
Empty the component disposal compartment (item 5 in fig.6.7 - 2), before you
shake components out of the feeder module.
PLEASE NOTE
The tensioned cover foil continues to transport the tape when the tape has been inserted
and exposes the components.
Do not press the lever if a component tape is inserted.
6 Working with the Machine User Manual SIPLACE CA-Series
6.7 Configuring the Feeder Modules From software version SC.708.0 Edition 12/2014 EN -DRAFT
372
Remove any loose components from beneath the pick-up window.
Close the pickup window (item 3) by returning the lever (item 4) to its original position.
Remove loose components from the changeover table with a brush or use a vacuum
cleaner with appropriate nozzle.
6
If the removal handle (item 1) is still protruding, then latch it in place.
6
Fig. 6.7 - 2 Checking the X feeder module before use
PLEASE NOTE
If the component tape is already inserted, cut it off flush with the front edge of the
feeder module.
(1) Removal handle (2) Cover foil rocker
(3) Pickup window (4) Lever for raising and latching the pick-up
window
(5) Component disposal compartment
User Manual SIPLACE CA-Series 6 Working with the Machine
From software version SC.708.0 Edition 12/2014 EN -DRAFT 6.7 Configuring the Feeder Modules
373
6.7.3.2 Inserting the X Feeder Module into the Changeover Table
6
Fig. 6.7 - 3 Inserting the X feeder module into the changeover table
(1) Front slider guide for the X feeder module
(2) Back slider guide for the X feeder module
(3) "Back" centering pin on the X feeder module
(4) "Front" centering pin on the X feeder module
(5) Recesses in the centering bar for holding the "back" centering pin
(6) Centering holes on the changeover table for holding the "front" centering pin
(7) Locking latches
(8) Guide profile for the changeover table (Ω profile)
(9) Insertion aid for the feeder module
6
Place the front slider guide (item 1) of the feeder module on the insertion aid (item 9) for the
component table.
Hold the feeder module vertically and push it forward, along the guide profile (item 8). The
front (item 1) and rear (item 2) slider guides of the feeder module slide on the guide profile
(item 8).
Carefully push the feeder module further until the "front" centering pin (item 4) is pushed into
the centering hole (item 6).