00197498-03_UM_SiplaceCA-Serie_EN - 第426页
7 Component and Die Handling User Manual SIPLACE CA-Series 7.2 SIPLACE X-Series Component Trolley From software version SC.708.0 Edition 12/2014 EN -DR AFT 426 7.2.1 S tructure of SIPLACE X-Series Component T rolley The …
User Manual SIPLACE CA-Series 7 Component and Die Handling
From software version SC.708.0 Edition 12/2014 EN -DRAFT 7.2 SIPLACE X-Series Component Trolley
425
The component trolleys are stand-alone modules that can be set up with feeders at an external
setup area. This means that the production process only has to be interrupted briefly in order to
change the component trolley.
7
Fig. 7.2 - 2 Component trolley, SIPLACE X-Series, with a PCB conveyor height of 950 mm
7
(1) Holes in the guide columns for the PCB transport heights of 900, 930 and 950 mm.
(2) Support block
(3) Changeover table
(4) Contact for switching the safety switch in the COT insert
7 Component and Die Handling User Manual SIPLACE CA-Series
7.2 SIPLACE X-Series Component Trolley From software version SC.708.0 Edition 12/2014 EN -DRAFT
426
7.2.1 Structure of SIPLACE X-Series Component Trolley
The component trolley essentially consists of the chassis, the changeover table for holding the
feeder modules, the tape reel container and the waste tape container.
7
Fig. 7.2 - 3 Component trolley, SIPLACE X-Series, front and rear view
(1) Chassis
(2) Changeover table
(3) Tape container
(4) Gap for accommodation of setup lists
(5) Waste tape container
(6) Handle
(7) Hand guard
7
CAUTION
Observe the safety instructions!
Observe the safety instructions in section 2.6.8, page 76, when you pull the tape re-
ject bin out of the component trolley.
User Manual SIPLACE CA-Series 7 Component and Die Handling
From software version SC.708.0 Edition 12/2014 EN -DRAFT 7.2 SIPLACE X-Series Component Trolley
427
Assemblies 7
In the standard version, the tape reel container (item 3 in fig. 7.2 - 3) holds tape reels up to a size
of 17" (432 mm).
There are two 5 mm wide gaps on the left and right, between the tape container and the compo-
nent trolley (item. 4 in fig. 7.2 - 3
) for storing setup lists.
The pullout waste tape container can be found beneath the chassis (item 5 in fig. 7.2 - 3
). The cut
waste tape travel down a chute into the waste tape container, which must be emptied as it fills up.
The handles (item 6 in fig. 7.2 - 3
) can be folded up or down.
7
7.2.2 Technical Data for the SIPLACE X-Series Component Trolley
7
7
PLEASE NOTE
Operational safety
All component trolleys or matrix tray changers must be docked on the machine in order to
operate it.
Fill any free locations with dummy feeder modules as described in
section 2.8.5
, page 98.
Length x width 727 mm x 592 mm
752 mm x 592 mm with reject bin
Height of the changeover table 889.5 mm for 900 mm PCB conveyor height
919.5 mm for 930 mm PCB conveyor height
939.5 mm for 950 mm PCB conveyor height
PCB conveyor height 900 mm ± 15 mm (option)
930 mm ± 15 mm (standard)
950 mm ± 15 mm (SMEMA option)
Height of handles when folded out 969 mm
Number of locations 40 (8 mm X tape feeder module)
Weight
Without feeder modules
With feeder module at all locations
80.4 kg
139.6 kg
Reel diameter
Standard
Maximum
Up to 432 mm (17")
483 mm (19")