00191494-01 - 第119页
Short Reference SIPLACE 80 S-15/F3/G Error Messages 03/99 Issue Software Version SR.010.x x 117 1 171 Error during Send INI data to GU CAUSE ● An error occurred while .ini dat a was being sent to the G U REMEDY ● Error i…
Error Messages Short Reference SIPLACE 80 S-15/F3/G
03/99 Issue Software Version SR.010.xx
116
1165 GU: Error while setting desired temperature
CAUSE
● While the desired temperature was being sent to the GU an error occurred
REMEDY
● Error is specified more precisely in a further message. Take this into account during troubleshoo-
ting
1166 GU: Error while setting glueing point volume
CAUSE
● While the glueing point volume change was being sent to the GU an error occurred
REMEDY
● Error is specified more precisely in a further message. Take this into account during troubleshoo-
ting
1167 GU: Error while setting new cartridge
CAUSE
● An error occurred while a command was being sent to the GU that a new cartridge had been
inserted.
REMEDY
● Error is specified more precisely in a further message. Take this into account during troubleshoo-
ting
1168 GU: Error while reading actual temperature
CAUSE
● While the actual temperature was being requested for the GU an error occurred
REMEDY
● Error is specified more precisely in a further message. Take this into account during troubleshoo-
ting
1169 GU: Error during Switch on continuous glueing
CAUSE
● While the continuous glueing of the GU was being switched on an error occurred
REMEDY
● Error is specified more precisely in a further message. Take this into account during troubleshoo-
ting
1170 GU: Error during Switch off continuous glueing
CAUSE
● While the continuous glueing of the GU was being switched off an error occurred
REMEDY
● Error is specified more precisely in a further message. Take this into account during troubleshoo-
ting
Short Reference SIPLACE 80 S-15/F3/G Error Messages
03/99 Issue Software Version SR.010.xx
117
1171 Error during Send
INI data
to GU
CAUSE
● An error occurred while .ini data was being sent to the GU
REMEDY
● Error is specified more precisely in a further message. Take this into account during troubleshoo-
ting
1172 GU: Error during Send process data
CAUSE
● An error occurred while process data was being sent to the GU.
REMEDY
● Error is specified more precisely in a further message. Take this into account during troubleshoo-
ting
1173 GU: Error during Receive process data
CAUSE
● An error occurred while process data was being received by the GU.
REMEDY
● Error is specified more precisely in a further message. Take this into account during troubleshoo-
ting
1174 WARNING: Fill cartridge before next PCB
CAUSE
● Bero for "Empty cartridge" triggered; not enough glue left to glue the next board
REMEDY
● Change cartridge and confirm
1175 Cartridge empty; PCB will not be processed
CAUSE
● This was preceded by error 1174 and the cartridge was still not changed
REMEDY
● Change cartridge and confirm
1176 Cleaning process must be started
CAUSE
● One of the cleaning conditions has occurred. Not an error
REMEDY
● The machine cleans itself automatically
1177 GU: Software error in RIO call
CAUSE
● Software error
REMEDY
● Siemens Service should be notified
Error Messages Short Reference SIPLACE 80 S-15/F3/G
03/99 Issue Software Version SR.010.xx
118
1178 Actual temperature does not reach desired temp.
CAUSE
● Glueing parameter controller did not reach the desired temperature
REMEDY
● Hardware should be checked
1179 Glue cleaning pad paper finished
CAUSE
● Glue cleaning pad finished
REMEDY
● Insert new paper
1180 Z-axis, GU1: Bero not activated during upward movement
CAUSE
● Z-axis is not moving upwards (sluggish); the bero is defective or set incorrectly
REMEDY
● Check the mechanism; check the bero; check the incremental transducer.
1181 Z-axis, GU2: Bero not activated during upward movement
CAUSE
● Z-axis is not moving upwards (sluggish); the bero is defective or set incorrectly
REMEDY
● Check the mechanism; check the bero; check the incremental transducer.
1182 Z-axis, GU3: Bero not activated during upward movement
CAUSE
● Z-axis is not moving upwards (sluggish); the bero is defective or set incorrectly
REMEDY
● Check the mechanism; check the bero; check the incremental transducer.
1183 Z-axis, GU1: Bero not released when axis at bottom
CAUSE
● Z-axis is not moving downwards (sluggish); the bero is defective or set incorrectly
REMEDY
● Check the mechanism; check the bero; check the incremental transducer.
1184 Z-axis, GU2: Bero not released when axis at bottom
CAUSE
● Z-axis is not moving downwards (sluggish); the bero is defective or set incorrectly
REMEDY
● Check the mechanism; check the bero; check the incremental transducer.