00191494-01 - 第42页
Error Messages Short Reference SIPLACE 80 S-15/F3/G 03/99 Issue Software Version SR.010.x x 40 377 Calibration value is out of ra nge (Error code 4FH) CAUSE ● Error during the course of calibration in the tester. REMEDY …
Short Reference SIPLACE 80 S-15/F3/G Error Messages
03/99 Issue Software Version SR.010.xx
39
370 Calibration value is out of range (Error code 48H)
CAUSE
● Error during the course of calibration in the tester.
REMEDY
● If electrical measuring is not possible, reset station; if resetting does not work, replace tester.
371 Calibration value is out of range (Error code 49H)
CAUSE
● Error during the course of calibration in the tester.
REMEDY
● If electrical measuring is not possible, reset station; if resetting does not work, replace tester.
372 Calibration value is out of range (Error code 4AH)
CAUSE
● Error during the course of calibration in the tester.
REMEDY
● If electrical measuring is not possible, reset station; if resetting does not work, replace tester.
373 Calibration value is out of range (Error code 4BH)
CAUSE
● Error during the course of calibration in the tester.
REMEDY
● If electrical measuring is not possible, reset station; if resetting does not work, replace tester.
374 Calibration value is out of range (Error code 4CH)
CAUSE
● Error during the course of calibration in the tester.
REMEDY
● If electrical measuring is not possible, reset station; if resetting does not work, replace tester.
375 Calibration value is out of range (Error code 4DH)
CAUSE
● Error during the course of calibration in the tester.
REMEDY
● If electrical measuring is not possible, reset station; if resetting does not work, replace tester.
376 Calibration value is out of range (Error code 4EH)
CAUSE
● Error during the course of calibration in the tester.
REMEDY
● If electrical measuring is not possible, reset station; if resetting does not work, replace tester.
Error Messages Short Reference SIPLACE 80 S-15/F3/G
03/99 Issue Software Version SR.010.xx
40
377 Calibration value is out of range (Error code 4FH)
CAUSE
● Error during the course of calibration in the tester.
REMEDY
● If electrical measuring is not possible, reset station; if resetting does not work, replace tester.
378 Calibration value is out of range (Error code 50H)
CAUSE
● Error during the course of calibration in the tester.
REMEDY
● If electrical measuring is not possible, reset station; if resetting does not work, replace tester.
379 Calibration value is out of range (Error code 51H)
CAUSE
● Error during the course of calibration in the tester.
REMEDY
● If electrical measuring is not possible, reset station; if resetting does not work, replace tester.
380 Calibration value is out of range (Error code 52H)
CAUSE
● Error during the course of calibration in the tester.
REMEDY
● If electrical measuring is not possible, reset station; if resetting does not work, replace tester.
381 Calibration value is out of range (Error code 53H)
CAUSE
● Error during the course of calibration in the tester.
REMEDY
● If electrical measuring is not possible, reset station; if resetting does not work, replace tester.
382 Calibration value is out of range (Error code 54H)
CAUSE
● Error during the course of calibration in the tester.
REMEDY
● If electrical measuring is not possible, reset station; if resetting does not work, replace tester.
383 Calibration value is out of range (Error code 55H)
CAUSE
● Error during the course of calibration in the tester.
REMEDY
● If electrical measuring is not possible, reset station; if resetting does not work, replace tester.
Short Reference SIPLACE 80 S-15/F3/G Error Messages
03/99 Issue Software Version SR.010.xx
41
384 BERO SZ1 not released
CAUSE
● Proximity switch defective; component jammed between screwdriver and segment;
motor of the screwdriver defective.
REMEDY
● Replace proximity switch, adjust sensing distance; remove component; check toothing for
damage; replace motor with hub, carry out calibration on the motor control board.
385 BERO SZ2 not released
CAUSE
Proximity switch defective; component jammed between screwdriver and segment;
motor of the screwdriver defective.
REMEDY
● Replace proximity switch, adjust sensing distance; remove component; check toothing for
damage; replace motor with hub, carry out calibration on the motor control board.
386 Input conveyor occupied
CAUSE
● When the belt speed was set there was a PCB board on the input conveyor; sensor defective
REMEDY
● Remove the PCB board; fit new sensor.
387 VS: No reaction from M10000 (reset M10000)
CAUSE
● M10000 crash; line interruption
REMEDY
● Reset M10000; check cable connection.
388 Check sum error in table program
CAUSE
● File TISCH.HEX erroneous.
REMEDY
● Replace file TISCH.HEX in the station computer.
389 Coplan.: Component will not be processed
CAUSE
● Measurement of a component for which no prepare command was sent to the coplanarity module
(error in the cluster and set-up)
REMEDY
● Respecify cluster and set-up.