00194798-01 - 第52页

Installation Manual, Station Software Version 602.01 Edition 06/2006 4.8.1.4 Installing the RMOS The following menu is displayed after the machine controller has booted from CD: DO YOU WANT TO CONTINUE RMOS INSTALLATION …

100%1 / 120
Installation Manual, Station Software Version 602.01 Edition 06/2006
51 of 60
Phoenix FirstBIOS(tm) Desktop CMOS Setup Utility
Integrated Peripherals
===================================================================
> OnChip DIE Device
> Onboard Device
> SuperIO Device
Phoenix FirstBIOS(tm) Desktop CMOS Setup Utility
Onboard Device
===================================================================
USB Controller [Enabled]
USB 2.0 Controller [Enabled]
USB Keyboard Support [Disabled]
USB Mouse Support [Disabled]
…
4.8.1.3.2.2 Activating the USB interrupt
Phoenix FirstBIOS(tm) Desktop CMOS Setup Utility
===================================================================
> Standard CMOS Features | > Frequency/Voltage Control
> Advanced BIOS Features | > Load Fail-Safe Defaults
> Advanced Chipset Features | > Load Optimized Defaults
> Integrated Peripherals | > Set Supervisor Password
> IMC Miscellaneous | > Set User Password
> Power Managment Setup | > Save & Exit Setup
> PnP/PCI Configurations | > Exit Without Saving
> PC Health Status |
Phoenix FirstBIOS(tm) Desktop CMOS Setup Utility
PnP/PCI Configurations
===================================================================
PNP OS Installed [No]
Reset Configuration Data [Disabled]
Resources Controlled by [Auto(ESCD)]
x IRQ Resources Press Enter
x IMA Resources Press Enter
PCI/VGA Palette Snoop [Disabled]
Assign IRQ for USB [Enabled]
. . .
→ Save the BIOS settings and exit the BIOS Setup.
Installation Manual, Station Software Version 602.01 Edition 06/2006
4.8.1.4 Installing the RMOS
The following menu is displayed after the machine controller has booted from CD:
DO YOU WANT TO CONTINUE RMOS INSTALLATION ?
[C] CONTINUE [P] PREPARE HARDDISK
[R] REBOOT SYSTEM
[T] TERMINATE BATCH PROCESS (Change to DOS)
PRESS KEY TO CONTINUE [C,R,T,P]?
→ Enter 'P' to create the partitions on the hard disk. The system is then booted.
→ When the menu shown above appears again, press 'C' (Continue) to actually install the RMOS.
The basic RMOS installation is now complete. The station software can be installed.
Caution:
After the RMOS has been installed, the USB interface on the machine controller
must be
deactivated, since an activated USB interface can lead to sporadic significant errors which are
difficult to localize.
52 of 60
Installation Manual, Station Software Version 602.01 Edition 06/2006
53 of 60
4.8.1.5 Deactivating the USB interface
4.8.1.5.1 Deactivating the USB controller
Phoenix FirstBIOS(tm) Desktop CMOS Setup Utility
===================================================================
> Standard CMOS Features | > Frequency/Voltage Control
> Advanced BIOS Features | > Load Fail-Safe Defaults
> Advanced Chipset Features | > Load Optimized Defaults
> Integrated Peripherals | > Set Supervisor Password
> IMC Miscellaneous | > Set User Password
> Power Managment Setup | > Save & Exit Setup
> PnP/PCI Configurations | > Exit Without Saving
> PC Health Status |
Phoenix FirstBIOS(tm) Desktop CMOS Setup Utility
Integrated Peripherals
===================================================================
> OnChip DIE Device
> Onboard Device
> SuperIO Device
Phoenix FirstBIOS(tm) Desktop CMOS Setup Utility
Onboard Device
===================================================================
USB Controller [Disabled]
x USB 2.0 Controller Enabled
x USB Keyboard Support Disabled
x USB Mouse Support Disabled
…
4.8.1.5.2 Deactivating the USB interrupt
Phoenix FirstBIOS(tm) Desktop CMOS Setup Utility
===================================================================
> Standard CMOS Features | > Frequency/Voltage Control
> Advanced BIOS Features | > Load Fail-Safe Defaults
> Advanced Chipset Features | > Load Optimized Defaults
> Integrated Peripherals | > Set Supervisor Password
> IMC Miscellaneous | > Set User Password
> Power Managment Setup | > Save & Exit Setup
> PnP/PCI Configurations | > Exit Without Saving
> PC Health Status |