00194798-01 - 第53页
Installation Manual, Station Software Version 602.01 Edition 06/2006 53 of 60 4.8.1.5 Deactivating the USB interface 4.8.1.5.1 Deactivating the USB controller Phoenix FirstBIOS(tm) Desktop CMOS Setup Utility ============…
Installation Manual, Station Software Version 602.01 Edition 06/2006
4.8.1.4 Installing the RMOS
The following menu is displayed after the machine controller has booted from CD:
DO YOU WANT TO CONTINUE RMOS INSTALLATION ?
[C] CONTINUE [P] PREPARE HARDDISK
[R] REBOOT SYSTEM
[T] TERMINATE BATCH PROCESS (Change to DOS)
PRESS KEY TO CONTINUE [C,R,T,P]?
→ Enter 'P' to create the partitions on the hard disk. The system is then booted.
→ When the menu shown above appears again, press 'C' (Continue) to actually install the RMOS.
The basic RMOS installation is now complete. The station software can be installed.
Caution:
After the RMOS has been installed, the USB interface on the machine controller
must be
deactivated, since an activated USB interface can lead to sporadic significant errors which are
difficult to localize.
52 of 60
Installation Manual, Station Software Version 602.01 Edition 06/2006
53 of 60
4.8.1.5 Deactivating the USB interface
4.8.1.5.1 Deactivating the USB controller
Phoenix FirstBIOS(tm) Desktop CMOS Setup Utility
===================================================================
> Standard CMOS Features | > Frequency/Voltage Control
> Advanced BIOS Features | > Load Fail-Safe Defaults
> Advanced Chipset Features | > Load Optimized Defaults
> Integrated Peripherals | > Set Supervisor Password
> IMC Miscellaneous | > Set User Password
> Power Managment Setup | > Save & Exit Setup
> PnP/PCI Configurations | > Exit Without Saving
> PC Health Status |
Phoenix FirstBIOS(tm) Desktop CMOS Setup Utility
Integrated Peripherals
===================================================================
> OnChip DIE Device
> Onboard Device
> SuperIO Device
Phoenix FirstBIOS(tm) Desktop CMOS Setup Utility
Onboard Device
===================================================================
USB Controller [Disabled]
x USB 2.0 Controller Enabled
x USB Keyboard Support Disabled
x USB Mouse Support Disabled
…
4.8.1.5.2 Deactivating the USB interrupt
Phoenix FirstBIOS(tm) Desktop CMOS Setup Utility
===================================================================
> Standard CMOS Features | > Frequency/Voltage Control
> Advanced BIOS Features | > Load Fail-Safe Defaults
> Advanced Chipset Features | > Load Optimized Defaults
> Integrated Peripherals | > Set Supervisor Password
> IMC Miscellaneous | > Set User Password
> Power Managment Setup | > Save & Exit Setup
> PnP/PCI Configurations | > Exit Without Saving
> PC Health Status |
Installation Manual, Station Software Version 602.01 Edition 06/2006
54 of 60
Phoenix FirstBIOS(tm) Desktop CMOS Setup Utility
PnP/PCI Configurations
===================================================================
PNP OS Installed [No]
Reset Configuration Data [Disabled]
Resources Controlled by [Auto(ESCD)]
x IRQ Resources Press Enter
x IMA Resources Press Enter
PCI/VGA Palette Snoop [Disabled]
Assign IRQ for USB [Disabled]
→ Save the BIOS settings and exit the BIOS Setup.
4.8.1.6 Restore initial configuration
→ Remove RMOS installation CD from the USB CD drive.
→ Remove the keyboard from the machine controller and connect it to the station computer.
→ Switch video multiplexer to SR1.
→ Disconnect the USB cable from the USB CD drive and the machine controller.
→ Press <Ctrl><Alt><Del> to warm start the machine controller.
4.8.2 BIOS update and settings
The current BIOS version and the required BIOS settings are supplied as ISO images on the installation
CD. These images can be used to create bootable CDs with suitable CD writing software on a PC with a
CD writer. These CDs can in turn be used to automatically update the BIOS and make the BIOS settings.
Procedure:
→ Create the CD 'CPU086_MC_BIOS_Update'.
→ Create the CD 'CPU086_MC_BIOS_Settings'.
→ Remove the keyboard from the station computer and connect it to the machine controller.
→ Switch the video multiplexer to SR2/MC.
→ Insert the CD 'CPU086_MC_BIOS_Update' in the USB CD drive and connect the drive to the machine
controller using a USB cable.
→ Press <Ctrl><Alt><Del> to warm start the machine controller.
→ During the warm start, press <Del>.
→ Set the BIOS so that the system boots from the USB CD drive (see section
4.8.1.3).
→ Reboot the machine controller and follow the BIOS update instructions.
→ Insert the CD 'CPU086_MC_BIOS_Settings'.
→ Reboot the machine controller and follow the BIOS setting instructions.
→ Reboot the machine controller and deactivate the USB interface again (see section
4.8.1.5).
→ Restore the initial configuration (see section 4.8.1.6).