HS50_advance_level 1_20200522_221201 (1) - 第169页

Studen t Guide HS-50 A dvanced I 06/200 2 Edition 5 DLM1 C&P Head 77 5.4. 14 Replacem en t of valve d rives 5.4. 14.1 T ools and equipment – Set of DIN 91 1 Allen keys – S et of P hilli ps screw dri vers – SITES T pr…

100%1 / 567
06/2002 Edition Student Guide HS-50 Advanced I
5 DLM1 C&P Head
76
5
Fig. 5.4 - 32 Turning station / DLM1
(1) Turning station / DLM1
(2) M3x25 hexagon socket-head screw
(3) Back part of the collect&place head
5.4.13.4 Fitting the DP station
➠ Make sure that the contact surfaces of the turning station and rear panel are clean.
➠ Insert the M3 x 25 hexagon socket-head screw (item 2 in Fig. 5.4 - 31) into the hole in the
centering station.
➠ Run the cable between the vacuum hose and the vacuum generation socket.
➠ Place the holes in the turning station on the parallel pins.
➠ Carefully push the turning station towards the back part until it reaches the stop.
➠ Fix the turning station with the hexagon socket-head screw.
➠ Plug the cable into sockets X12 and X18 on the head board (see item X12 and X18 in Fig.
5.4 - 31
, page 5 - 75.
5.4.13.5 Settings
➠ Switch the placement system on and start it up.
➠ Use the SITEST program to run a function test.
Student Guide HS-50 Advanced I 06/2002 Edition
5 DLM1 C&P Head
77
5.4.14 Replacement of valve drives
5.4.14.1 Tools and equipment
– Set of DIN 911 Allen keys
– Set of Phillips screwdrivers
– SITEST program
– Feeler gauge, item no. 00325445-01
5.4.14.2 Parts
Valve positioning drive, placement circuit, item no. 00349433-01 (Pos. 1 in Fig. 5.4 - 10)
Valve positioning drive, reject circuit, item no. 00349432-01 (Pos. 2 in Fig. 5.4 - 10
) 5
5.4.14.3 Dismantling the valve positioning drive
➠ Remove the collect&place head from the head mount (see section 5.4.12.3, page 5 - 69).
➠ Undo the two M2x6 Phillips screws on the ribbon cable clamp (items 3 and 4 in Fig. 5.4 - 10).
➠ Undo the M3x10 hexagon socket-head screw (item 4 in Fig. 5.4 - 10).
➠ Carefully remove the valve positioning drive (item 1 or 2 in Fig. 5.4 - 10).
06/2002 Edition Student Guide HS-50 Advanced I
5 DLM1 C&P Head
78
5
Fig. 5.4 - 33 Replacing the valve positioning drive
(1) "Placement circuit" valve positioning drive
(2) "Reject circuit" valve positioning drive
(3) Back part of the collect&place head
(4) M3x10 hexagon socket-head screw
(5) Parallel pins, 2 x per drive
5
5.4.14.4 Fitting the valve positioning drive
➠ Insert the valve positioning drive, making sure that it is seated correctly on the parallel pins.
➠ Loosely tighten the hexagon socket-head screw.
➠ Use the cable clamp assemblies (items 2, 3, and 4 in Fig. 5.4 - 11) to fix the ribbon cables in
position, ensuring that the ribbon cables are not squashed.