HS50_advance_level 1_20200522_221201 (1) - 第394页
S tud ent Guid e HS-50 A dvanced I E dition 06/2 002 1 1 P neumatic Cutt er and Empty- T ape Du ct 7 - 2 Fixing ped estal for cable tie 00318666-01 2 al together adhes iv e type - 2 Cable tie (W = 2,4mm, L = 92mm) 008051…
Edition 06/2002 Student Guide HS-50 Advanced I
11 Pneumatic Cutter and Empty-Tape Duct
6
11.2 Parts
NOTE:
These instructions are only valid for the version 04 pneumatic cutter and the associated version
03 empty-tape duct.
One of the new features of cutter version 04 is a tape deflector which is installed over the movable
blade (see Fig. 11.4.3 -> 19).
The movable blade, the stationary blade and the spacers under the holddowns (see Fig. 11.4.2
-> 6, 11, 16) are attuned to one another and must therefore always be exchanged as a set.
The holddowns match the version 04 cutter (= with tape deflector).
Tape deflectors and tape deflector holders are not spare parts.
The one-way restrictor is not a spare part.
The empty-tape duct is not part of the “pneumatic cutter”. 11
Quantity Designation: Item No.: Note:
- 1 Pneumatic cutter HS-50 00324065-04 Height of empty tape in
accordance with feeder
modules used on HS-50
- 1 Empty-tape duct assembly 00334290-03 for changeover table area
- 1 Baffle, inside 00334295-02
- 1 Baffle, outside 00334296-01
- 1 Reject box 00334297-01
- 1 Kit of blades (stationary + movable 00335581-02 see NOTE above
blade + 2 spacers)
- 4 Rubber-metal vibration damper 00329209-01 2 each on left and right
- 2 (Solenoid) valve assembly 00330930-01 1 each on left and right
- 2 Short-stroke cylinder assembly HS-50 00349898S01 1 each on left and right
with adjusted one-way restrictor
- 2 Articulated joint (complete), with chamfer 00348579-02 1 each on left and right
- 1 Deflector plate 00329540-03 1 altogether
- 1 Cover plate (for control board) 00340658-01 1 altogether
- 2 Holddown 00328731-03 1 each on left and right
- 4 Proximity switch 00332894-01 2 each on left and right
with cable tape cutter S50
- 1 Cable: Control board tape cutter- valve 00334380-01 for valve RH
- 1 Cable: Control board tape cutter- valve 00332896-01 for valve LH
- 1 Control board tape cutter S50 00329699-03 for F5, S-23, HS-50
(= control unit / control board box)
Student Guide HS-50 Advanced I Edition 06/2002
11 Pneumatic Cutter and Empty-Tape Duct
7
- 2 Fixing pedestal for cable tie 00318666-01 2 altogether
adhesive type
- 2 Cable tie (W = 2,4mm, L = 92mm) 00805140-01
- 1 If needed: Adhesive label (with text) 00324065-04 German and English
- 1 If needed: Adhesive label (with text) on request EU languages
- 1 If needed: Adhesive label: Triangular
warning symbol "Hand injury" 00335957-01
11.3 Tools, Expendable Materials, Documentation
– Thick protective gloves
– Set of socket wrenches, cross-slotted screwdriver size 4,
– Open-end wrench, width across flats 10; slotted screwdriver size 1
– Torque wrench
– Diagonal cutter
– Sliding caliper
– Feeler gauge 0.05mm; 1.0mm; 1.5mm, 2.0mm; 2.50mm
– Straight-edge (for check of tape deflector)
– Mounting plate, Item no.: 00312731-01
– 2 large parallel clamps (or mounting plate, see above)
– Flat, sturdy work bench to fasten the removed cutter (or mounting plate, see above)
– Loctite no. 234,, Item no.: 00334892-01
– Molykote paste, Item no. 02100335-01, 250 g, (preferred) or
ISOFLEX TOPAS NCA 52, Item. no. 00330850-01, tube 50 g
– Water-insoluble, fine-tip marker
– A dry and clean cloth
– Operating manual for SITEST program, Version 501.xx, English, Item No. 00191417-01
Edition 06/2002 Student Guide HS-50 Advanced I
11 Pneumatic Cutter and Empty-Tape Duct
8
11.4 Overview of Mechanical Layout
11
Fig. 11.4.1 Overview of Pneumatic Cutter Version 04 and Empty-Tape Duct Version 03