3OM-1751-002w_G5S.pdf - 第245页
3OM-1751 2-77 1303-001 · Set-up 2 [1] [2] [3] F3B74 [1] Cutter operation set-up Block 1, 2 Specify the following items for each cutter operation. Mode Select one of the following options to determine whether or not the c…
3OM-1751
2-761303-001
[4] Fdr(Noz) msg rate
Err count [times], pick [times]
Error counts and # of picks [times] Set the parameters to show the nozzle
No. whose pickup rate has deteriorated during automatic operation.
When the number of picks has reached the specied value, the parameter in
the "Error counts" text box is cleared.
Note
The number of picks and pick-up errors is managed for each individual
nozzles but the parameters of "Error counts" and "# of picks" is equally
reected on every nozzle.
Guide
"WARNING", "Stop (Cycle stop), or "Pause" can be selected to determine
in which mode the machine should be set when the number of pickup errors
has reached the specied error counts before the number of picks reaches
the specied number of picks. When "WARNING" is selected, a warning
message is issued as machine information. "Stop (Cycle stop)" stops the
machine after one cycle of operation and "Pause" sets the machine in the
"PAUSE" mode.
Note
When both "Error counts" and "# of picks" are set "0" (zero) or "Error
counts" is set to a number larger than "# of picks", no warning message is
issued.
[5] Noz replace in the lowering of picks
Select "Enable" or "Disable" to change the nozzle automatically to a spare
nozzle in the stocker when the successful component handling rate is lowered
during the automatic operation.
Note
(a) The automatic change only for the high-speed nozzle is available.
(b) A spare nozzle should be setup in the stocker in advance.
[6] Feeder Base Up/Down Opn restrictions
3.1 "Auto Ope. Set-up" Tab Sheet
3OM-1751
2-771303-001
·
Set-up 2
[1]
[2]
[3]
F3B74
[1] Cutter operation set-up
Block 1, 2
Specify the following items for each cutter operation.
Mode
Select one of the following options to determine whether or not the cutter
function should be used.
Not Cut
After Pick-up(leng des)
At Transfer(leng des)
At Transfer(every time)
Cancel
Length [mm]
Set the length of the tape to be cut by each cutter.
Deceleration
Select one of the following options to determine the rate of the speed
reduction.
Full Speed, 10%Decr, 20%Decr, 30%Decr, 40%Decr,
50%Decr, 60%Decr, 70%Decr, 80%Decr, 90%Decr
[2] Linear measure
Block 1, 2
Whether or not the measurement using the linear measure is enabled, is
selected in this data box.
3.1 "Auto Ope. Set-up" Tab Sheet
3OM-1751
2-781303-001
[3] Cone Recog
Block 1, 2
Whether or not the corn recognition is performed automatically per head, is
set in this selection box.
AUTO
: When selected, the corn recognition is performed automatically.
Disable
: When selected, the corn recognition is not performed.
Note
(a) When the corn recognition function is used, the reference mark
recognition is not available.
(b) It is available when the high-speed head is used.
•
Set-up 3
[1]
[3]
[4]
[2]
[5]
[6]
[7]
F3B75
[1] Dclr of conveyor width's axis
Select the deceleration setting each for conveyor width axis from the
following items.
Full Speed, 10% Decr, 20% Decr, 30% Decr, 40% Decr,
50% Decr, 60% Decr, 70% Decr, 80% Decr, 90% Decr
Note
When the ambient temperature is lower than the specied temperature (20°C
± 10°C), perform the deceleration setting each for the conveyor width axis
and backup axis referring to the following setting standard.
•
Setting Standard based on Ambient Temperature
10°C or more : Full Speed
7 to 10°C : 50%
Less than 7°C : 70%
3.1 "Auto Ope. Set-up" Tab Sheet