OM-1241-005_w - 第135页
4-8 AIX-ML T-ID 3. Maintenance Spots 3.1 Whole View Notice Any operations with a cover(s) being removed are included. After the maintenance work, be sure to attach the cover back in place. T raverse Elevator Shaft Magazi…
4-7
AIX-MLT-ID
2.2 Quarterly Maintenance
Note
DE1: DAPHNE EPONEX GREASE No. 1
NM1: MOLYNOC GREASE AP1
Table D5
Object Units
Inspection, Cleaning,
and Lubrication Spots
Work Grease Required Items Check
3.3.1
Pallet
Rail Inspection
-
Scale
Top Surface Inspection
-
Scale
3.3.2
Elevator Shaft
Ball Screw Lubrication DE1 Oiled Rag and Brush
Linear Guide Lubrication DE1 Oiled Rag, Brush and
Hand Grease Gun
Belt Inspection
-
Visual Inspection
3.3.3
Traverse
Pallet Receiver Inspection
-
Visual Inspection
Linear Guide Lubrication DE1 Oiled Rag, Syringe, and
Nozzle (No. 18)
Pallet Chuck Lubrication DE1 Oiled Rag, Syringe, and
Nozzle (No. 18)
3.3.4
Magazine Base
Cylinder Connection
Section
Lubrication NM1 Oiled Rag, Syringe, and
Nozzle (No. 18)
3.3.5
Magazine
Rack Shutter Fulcrum
Section
Lubrication NM1 Oiled Rag, Syringe, and
Nozzle (No. 18)
2.3 Yearly Maintenance
Note
DE1: DAPHNE EPONEX GREASE No. 1
Table D5-1
Object Units
Inspection, Cleaning,
and Lubrication Spots
Work Grease Required Items Check
3.3.4
Magazine Base
Magazine Rail Lubrication
DE1
Oiled Rag, Syringe, and
Nozzle (No. 18)
0705-003
2. Maintenance Check List
4-8
AIX-MLT-ID
3. Maintenance Spots
3.1 Whole View
Notice
Any operations with a cover(s) being removed are included.
After the maintenance work, be sure to attach the cover back in
place.
Traverse
Elevator Shaft
Magazine Base
Fig. D2
Reference
Refer to "3.3" and the subsequent items for the detailed information on the
spots of each section to be maintained and how to maintain them.
0705-003
3. Maintenance Spots
4-9
AIX-MLT-ID
3.2 Understanding of Maintenance Items on Each Section
0705-003
3.2 Understanding of Maintenance Items on Each Section
The following describes how to view the description of each eld (numbered
elds) in "3.3 Inspection, Cleaning, and Lubrication Spots".
View of Inspection, Cleaning, and Lubrication Spots
(ExampleofIdentication)
Pallet
Every Month Inspection and Cleaning
Required Time: 1 minute
When the pallet is dirty, clean both top and
bottom surfaces with a rag.
Top Surface
Every 3 Months Inspection
Required Time: 1 minute
Check for the warpage of the pallet with a
scale. (Up to Max. 0.5 mm)
Rails
Every 3 Months Inspection
Required Time: 2 minutes
Check the wear of the bottom surfaces of
the pallet rails with a scale.
(Up to Max. 0.5 mm)
[1]
[4]
[3][2]
Fig. D3
[1]:
Maintenance Spot
[2]:
Cycle and Contents of Maintenance
[3]:
Details of Maintenance
[4]:
This indicates roughly estimated time required for maintenance work.
(This is included in the time required to attach or detach a cover, etc.)