00198500-02_VD_711.1_R18-1_DE_EN - 第35页

Station Software 71 1.1 (R18 - 1) / Versio n Description 05/2018 Edition 35 D1 - 142505101 The software h ung u p and had to be rest arted. D1 - 142515201 CA4: When the mappi ng ACT wa s performed , the fiducial s we re …

Station Software 711.1 (R18-1) / Version Description 05/2018 Edition

710.1 Patch 2

Error no. Error description

D1-139125591 At a TX machine, an error message was displayed that the weight dependent

motor current was too big.

D1-140020401 There was an unhandled exception when a tray was used on a carrier.

D1-140048801 The reject bin configuration was not displayed correctly on the GUI.

D1-141199449 The station software stopped during / after placement with error message

30016 Unhandled exception error

D1-141376801 When the embedded Software was updated, error message 30554

Subsystem is not responding (dp axis)

was displayed.

D1-141376849 The state of the board was displayed even if the board had reached the output

conveyor.

D1-141386801 The component sensor data was invalid and could not be restored.

D1-141541301 Status 30622 Nozzle missing was not reset for the nozzle.

D1-141564601 Coplan-MCT was not possible: instead of using the SST33 camera the SST25

was used. With this camera the calibration failed.

D1-141619501 After a machine restart, the message 30450 WPC2 unspecified

hardware error

was displayed.

D1-141670801

D1-141138729

D1-142037601

eSW: After restarting the machine, the message 30555 Subsystem is

not activated (main distributor) was displayed sporadically, but

machine worked without any problems.

D1-141993601 The button to change the acceleration of JTF-ML2 was missing.

D1-142003201 The Edit pickup point function should get a separate user level.

D1-142176533 The machine stopped during production.

D1-142207343 It was not possible to change the filling level of the JTF.

D1-142229001 During the shutdown of the machine, error message unhandled exception

error

was displayed.

D1-142248701 C&P20 M2 segments were not recognized.

D1-142266401 Along with the "LBO 1500" option, support pins could not be set.

D1-142276101 eSW: TX micron with station software 710.1: Along with vacuum tooling there

was always an error with the lifting table motors during board loading.

D1-142283901 Several problems with vacuum tooling with station software 710.1.

D1-142290001 Error message 30977 Timeout acquiring resources was displayed

and the board disappeared on the GUI.

D1-142328345

D1-142328387

D1-142328735

Teaching the pickup position during production resulted in a software hang-up.

D1-142441301

D1-142325401

eSW: The x-axis parametrization could not be executed any longer.

Station Software 711.1 (R18-1) / Version Description 05/2018 Edition

D1-142505101 The software hung up and had to be restarted.

D1-142515201 CA4: When the mapping ACT was performed, the fiducials were measured

only with the master gantry. There was no dual gantry transformation.

D1-142536004 The station software hung up when the user level was changed.

D1-142624049 When a carrier X was set up, the station reported feeder missing;

pickup not possible

D1-142673101 The Skip recognition button was active on the basic production level. The

activity level could be changed now.

D17915-12902 The first component was not picked up after feeder error.

D18317-2201 The machine stopped during production without any error message.

D18164-10301 Omitted tracks were reset when the setup was changed, but not when the

same job was downloaded again. A job download should also activate the

track.

Table 9-7: Corrected errors station software version 710.1 Patch 2

710.1 Patch 1

Error no. Error description

D1-130023341 The measurement of cycle time did not work for some configurations.

D1-140150945 Confirming the exchange of a cassette did not set the levels full.

D1-140532401 LED-Centering: the glass plate was worn out too fast.

D1-140754501 After a reboot after a virus scan, the software did not start any longer.

D1-140811309 After a partial download, all feeder LEDs were on until the table was taken out

and in again.

D1-141145401 It was not possible to download an accuracy of 25µm for SST45.

D17754-11401 Gantry 2 waited for gantry 3 several cycles before it started to place.

D18224-30501 A board in lane 2 was placed only when lane 1 got empty. The reason was a

safety distance which is needed when a high component is placed on the side

of the CPP gantry. This distance value was slightly too high.

Table 9-8: Corrected errors station software version 710.1 Patch 1

Station Software 711.1 (R18-1) / Version Description 05/2018 Edition

10 Important Terms and Abbreviations

CA4

CA4 V2

Machine type of the Chip Assembly (CA)-series with 4 gantries

and 2 PAs

C&P Collect & Place

CPP Collect & Place & Pick & Place

DC Dual Conveyor

DX1/DX2 Machine type with 1 or 2 gantries and 1 PA

EDIF Electronic Design Interchange Format

eWLP embedded Wafer Level Process

FOPLP Fan-Out Panel Level Packaging

FCCS Field Camera Calibration System

GUI Graphical User Interface

HFH High Force Head

HW Hardware

MGCU Modular Gantry Control Unit

MHCU Modular Head Control Unit

MTC Matrix Tray Changer

OIS Operator Information System

PA Processing area

PCB Printed circuit board

Placement mode:

2-in-1

When a machine runs in I-Placement mode, it is possible to

perform manual operations for one side / gantry. This placement

mode is also called "independent".

Placement mode:

Alternating

Placement mode in a dual gantry placement area, in which both

gantries place components on both boards in a dual conveyor.

First, both gantries place all assigned components on the board

in lane one and then on the board in lane two.

Placement mode:

Borrow

Performance

A line runs in I-Placement mode and to get a balanced

throughput between the left and right conveyor lanes, e.g. the

last machine runs in Alternating mode and places components in

this placement area on the board of the other lane.

Placement mode:

I-Placement

Placement mode in a dual gantry placement area in which each

gantry only places components on the board of the assigned

conveyor lane.

SC Single Conveyor

SC SIPLACE Setup Center (external setup control system)

SW Software

SWS SIPLACE Wafer System

SX1/SX2 Machine type with 1 or 2 gantries and 1 PA

TH Twin Head

TH HF Twin Head High Force