00196429-0102 - AI Head Reconfiguration Kit SX12 C - 第53页

Installing the C&P20A Placement Head Inserting the C&P20A Head Into the Machine Assembly of the C&P20A Placement Head Assembly Instructions / Montageanleitung Head Reconfiguration K it C&P20A 53 Assembly …

100%1 / 64
Installing the C&P20A Placement Head
Disassembling the TwinHead Conversion of the Head Adapter
52 Assembly Instructions / Montageanleitung Head Reconfiguration Kit C&P20A
Fitting the HCU onto the base adapter for CPP and C&P20A head
Installing the head adapter for CPP and C&P20A head
Fitting and fixing the HCU
► Carefully fit a HCU of the TwinHead onto the base
adapter of the parts set (1).
► Fix the HCU with the four previously removed screws
(2 and 3).
Mounting position for the head adapter
Legend
(1) - (7) Fastening bolts on the mounting position
Head adapter
Legend
(1) – (7) Fastening points on the head adapter
► Place the head adapter onto the fastening bolts in the
mounting position and fasten it with the 7 screws.
► Connect the head interface board via the plug con-
nector with the head interface.
CAUTION
Installation instructions
► Check the firmware and perform a download, if needed.
Installing the C&P20A Placement Head
Inserting the C&P20A Head Into the Machine Assembly of the C&P20A Placement Head
Assembly Instructions / Montageanleitung Head Reconfiguration Kit C&P20A 53
Assembly of the C&P20A Pla cement Head
3.4 Assembly of the C&P20A Placement Head
See also
1.2 Preparatory Work... [ ➙ 38]
Inserting the C&P20A Head Into the Machine
3.4.1 Inserting the C&P20A Head Into the Machine
Parts, Equipment and Tools
▪ Torque screwdriver 100-500 Ncm [03078400-xx]
▪ Extension/straight TX20 [03073256-xx]
▪ Bit holder for Torque Vario-S screwdriver [03078706-xx]
Installation
CAUTION
Installation instructions
► Make sure that the assembly position on the head plate is correct.
► Tighten the M4x14 screws with a torque of 2.7 Nm.
Fixing positions of the C&P20A head on the head plate
Legend
1. Hook for hanging up the C&P20A head
2. Support pin
3. Freely accessible fixation point
4. Freely accessible fixation point
5. Freely accessible fixation point
6. Fixation point covered by pressure control valve
► Connect the discharged air hose to the return cylin-
der. You can lay the remaining piping and data lines
when the head is installed.
► Hold the head at its handle and carefully insert it onto
the locating pins of the head plate.
► Tighten the three freely accessible head screws
M4x14 (1, 2, 3) with a long Torx screwdriver.
Installing the C&P20A Placement Head
Assembly of the C&P20A Placement Head Connecting the C&P20A Head
54 Assembly Instructions / Montageanleitung Head Reconfiguration Kit C&P20A
Connecti ng the C&P20A Hea d
3.4.2 Connecting the C&P20A Head
► Connect the flat ribbon cable to the head and the base adapter (1).
► Fix the strain reliefs of the component camera cables (2 and 3) and connect the cables to the vision
board.
► Connect all pneumatic connections to the C&P20A (4 and 5) and to the compressed air distributor.
► Connect the discharged air hose to the silencer (6).
► Close the lower connection at the silencer with the cover cap [03006728-xx].
Tightening the covered head screw
One of the four head screws by means of which the
C&P20A head is fixed to the head plate is located behind
the pressure control valve. The pressure control valve
has to be swivelled to the left to gain access.
The covered head screw can now be accessed via a
guide drilling.
► Insert the Torx screwdriver into the guide drilling and
push it backwards until it sets down on the the head
screw.
► Tighten the covered head screw M4X14.
Connecting lines
Legend
1. Flat ribbon cable [03065867-xx]
2. Strain relief component camera cable
3. Strain relief component camera cable
4. Hose / Pressure control valve C+P20 [03016216-xx]
5. ESD tube / holding circle C+P20 [03070202-xx]
6. Discharged air hose to silencer
7. Cover cap [03006728-xx]