4OM-1064-001 - 第29页
1-19 Fig. 1.20-1 X/Y Beam (Beams A and B) X-Axis 0004-002 Tg0249-PM-MM X-Axis Ball Screw Cleaning and Lubrication (DE1) (1) W ipe off old grease with an oiled rag. Note: T ake care not to leave any waste thread. (2 ) Lub…
1-180004-002 Tg0249-PM-MM
A
Beam A Side
Beam B Side
A
Fig. 1.19 Feeder Base
Cam and Cam Follower
Lubrication (NM1)
(1) Remove the plate on the side of
the feeder base as shown in the
figure.
(2) Apply new grease with a brush, etc.
The cam and cam follower are lo-
cated in the depth of Arrow A.
Note: Lubricate it covering this
section with cloth, etc. to
avoid dropping grease
onto the wiring.
7. Maintenance (Every 3 Months after Initial Maintenance in 1 Month)
1-19
Fig. 1.20-1 X/Y Beam (Beams A and B) X-Axis
0004-002 Tg0249-PM-MM
X-Axis Ball Screw
Cleaning and Lubrication (DE1)
(1) Wipe off old grease with an oiled
rag.
Note: Take care not to leave
any waste thread.
(2) Lubricate the 2 nipples with new
grease from a grease gun.
Note: The attachments to be
used are SPK-3C, U type
and P type.
Fig. 1.20-2 X/Y Beam (Beams A and B) X-Axis
Beam A Side
Beam B Side
X-Axis Linear Guide
Cleaning and Lubrication (DE1)
(1) Wipe off old grease with an oiled
rag.
Note: Take care not to leave
any waste thread.
(2) Lubricate the 8 nipples with new
grease from a grease gun.
Note: The attachment to be
used is H type.
SPK-3C
U Type
P Type
Beam A Side
Beam B Side
Nipple
Nipple
Nipple
2 nipples
2 nipples
2 nipples
2 nipples
Nipple
Nipple
H Type
7. Maintenance (Every 3 Months after Initial Maintenance in 1 Month)
1-20
Nipple
Nipple
Nipple
Nipple
Fig. 1.21 X/Y Beam (Beams A and B) Y-Axis
0004-002 Tg0249-PM-MM
Beam A Side
Beam B Side
Fig. 1.22 Placement Head
Y-Axis Ball Screw
Cleaning and Lubrication (DE1)
(1) Wipe off old grease with an oiled
rag.
Note: Take care not to leave
any waste thread.
(2) Apply new grease by hand or with
a brush.
Y-Axis Linear Guide
Cleaning and Lubrication (DE1)
(1) Wipe off old grease with an oiled
rag.
Note: Take care not to leave
any waste thread.
(2) Lubricate the 8 nipples with new
grease from a grease gun.
Note: The attachments to be
used are SPK-3C, U
type and P type.
SPK-3C
U Type
P Type
Ball Screw and Linear Guide
Cleaning and Lubrication (DE1)
(1) Wipe off old grease with an oiled
rag.
Note: Take care not to leave
any waste thread.
(2) Lubricate the 4 nipples with new
grease from a grease gun.
Notes: (a) For the lubrication
procedure, refer to
“10.1 Placement
Head and PCB Posi-
tioning Section”.
(b) The attachments to
be used are U type
and N type.
U Type
N Type
Nipple
Nipple
Beam A Side
Beam B Side
Nipple
Nipple
2 nipples
2 nipples
Nipple
Nipple
Nipple
7. Maintenance (Every 3 Months after Initial Maintenance in 1 Month)