4OM-1064-001 - 第33页
1-23 0004-002 Tg0249-PM-MM 8. Maintenance (Every 3 Months) Fig. 1.26 Control Box Dust Filter Cleaning ( 1 ) After removing the setscrews, draw it out, holding the knobs on the right and left sides. ( 2) Clean dirt and du…
1-22
Air Filters
Cleaning
(1) Remove the air filter.
Align the mark with the release position by pressing
and turning the button at the same time. Then, draw the
outer case downward to remove. Remove the inner air
filter by turning it in the direction of Arrow A.
(2) Blow off dust with compressed air.
(3) Mount the air filter.
Mount the air filter turning it in the direction of Ar-
row B.
Mount the outer case and at the same time press and
turn the button to align the mark with the locking
position.
Button
Lock
Unlock
B
A
Table 1.8
8. Maintenance (Every 3 Months)
0004-002 Tg0249-PM-MM
8. Maintenance (Every 3 Months)
Fig.1.24 Air Regulator
Maintenance Spots Check
Name
Fig.
No.
Description Grease
Cleaning
Tools,
Nozzles, etc.
Air Regulator Air Filters 1.24 Cleaning Air Gun
Vacuum Pressure
System
Aggregated Vacuum
Filter
1.25 Cleaning Air Gun
Control Box Dust Filter 1.26 Cleaning Vacuum
Cleaner
Beam A side
1-230004-002 Tg0249-PM-MM
8. Maintenance (Every 3 Months)
Fig. 1.26 Control Box
Dust Filter
Cleaning
(1) After removing the setscrews,
draw it out, holding the knobs on
the right and left sides.
(2) Clean dirt and dust with a vacuum
cleaner.
Fig. 1.25 Vacuum Pressure System
Filter Case
C
Aggregated Vacuum Filter
Cleaning
(1) Remove the filter case by turn-
ing in the direction of Arrow C
and remove the inner filter.
(2) Blow off dust with compressed air.
Beam B side
CAUTION
Use protective devices to avoid any accident which
may be caused due to the tight work space.
Unit : mm
Note: The dimensions in the figures
are design values.
Knob
Setscrew
1-24
Table 1.9
9. Maintenance (Every 6 Months)
Notes: (a) Grease Symbols
DE1 : DAPHNE EPONEX GREASE No.1
NM1 : NEW MOLYNOC GREASE No.1
KS64 : SILICONE GREASE KS64
(b) If SILICONE GREASE KS64 (SHIN-ETSU CHEMICAL CO.) is not
available, use grease specified as follows.
Fluorine Type Grease, BARRIERTA IEL/V (NOK KLUBER)
When BARRIERTA IEL/V is used, gently wipe grease over spots to be
lubricated.
9. Maintenance (Every 6 Months)
0004-002 Tg0249-PM-MM
Maintenance Spots Check
Name
Fig.
No.
Description Grease
Cleaning
Tools,
Nozzles, etc.
PCB Positioning
Section
Linear Guide 1.27 Cleaning and
Lubrication
DE1 Oiled Rag,
Hand or
Brush
Ball Spline
4 places
1.28 Cleaning and
Lubrication
DE1 Oiled Rag,
SPK-3C
Conveyor Linear Guides
(4 nipples)
1.29 Cleaning and
Lubrication
DE1 Oiled Rag, U
and N Types
Ball Screws and Nut 1.29 Cleaning and
Lubrication
DE1 Oiled Rag,
Hand or
Brush
Splines 1.29 Cleaning and
Lubrication
NM1 Oiled Rag,
Hand or
Brush
X-Axis
Side of Cable
1.30 Cleaning and
Lubrication
KS64 Oiled Rag,
Hand or
Brush
X-Axis
Cable Fixing Position
1.30 Checking
X-Axis
Upper/Lower Cable
Guides
1.30 Cleaning and
Lubrication
KS64 Oiled Rag,
Hand or
Brush
Y-Axis
Side of Cable
1.31 Cleaning and
Lubrication
KS64 Oiled Rag,
Hand or
Brush
Y-Axis
Cable Fixing Position
1.31 Checking
X/Y Beam
(Beams A and B)
Y-Axis
Lower Cable Guide
1.31 Cleaning and
Lubrication
KS64 Oiled Rag,
Hand or
Brush