Horizon UserManualV6 - 第111页

Parameter Definition Right Feed Delay This parameter sets a time delay on the board stop to allow for irregular shaped boards when fed from the right. Minimum 0sec Maximum 3secs Increments 0.1sec steps NOTE Not used whil…

100%1 / 378
Parameter Definition
Tooling Type This determines which type of board support is to be used with this particular product.
Options are:
Vac for Flex, AutoFlex, Vacuum, Magnetic Pillars (see Tooling)
Flatten Vacuum Delay This parameter determines the duration of vacuum applied whilst the board is pressed
against the underside of the screen with Vac for Flex enabled.
Minimum 0 sec
Maximum 5 secs
Default 2 secs
Increment 0.1 sec
Separation Vacuum
Delay
This parameter determines the duration of vacuum applied after printing and before the
rising table is lowered to separation height with Vac for Flex enabled.
Minimum 0 sec
Maximum 5 secs
Default 2 secs
Increment 0.1 sec
Print Front Limit This determines the distance from the front edge of the board that printing must start.
Minimum -6.5mm
Maximum Board width - print rear limit
Increment 0.1mm
Default 0mm
NOTE
With Paste Trails enabled or ProFlow fitted the minium value is 0mm.
Print Rear Limit This determines the distance from the rear edge of the board that printing must start.
Minimum -6.5mm
Maximum Board width - print front limit
Increment 0.1mm
Default 0mm
NOTE
With Paste Trails enabled or ProFlow fitted the minium value is 0mm.
Board Stop X This parameter determines the distance from the centre line of the machine to the board
stop position.
Minimum 0mm
Maximum 255mm
Increment 0.1mm
Default Half of the board length set in the board
file, (board located centrally)
NOTE
Not used while remote board stop is fitted.
Board Stop Y This parameter determines the distance from the fixed rail to the board stop position.
Minimum 25mm
Maximum Board width minus 15mm
Increment 0.1mm
Default Two thirds of the board width
NOTE
Not used while remote board stop is fitted.
Remote Board
Stop X
This parameter determines the displacement of the remote board stop from the camera
reference position.
Minimum Minimum Board Length ÷ 2
Maximum Board Length
Increment 0.1
Default Board Length ÷ 2
NOTE
Only used while remote board stop is fitted.
1.94 User Manual Software Version 6
MACHINE PROGRAMMING
MENU PARAMETERS
Parameter Definition
Right Feed Delay This parameter sets a time delay on the board stop to allow for irregular shaped boards
when fed from the right.
Minimum 0sec
Maximum 3secs
Increments 0.1sec steps
NOTE
Not used while remote board stop is fitted.
Alignment Weighting This is only used in 2 fiducial mode and sets a value determining how much of the
fiducial spacing error is assigned to fiducial 2.
Minimum 0%
Maximum 100%
Increment 1%
Default 50% (see vision system)
X Align Weighting This is only used in 3 fiducial mode and sets a value determining where the X axis
alignment should be optimized.
Minimum 0%
Maximum 100%
Increment 1%
Default 50% (see vision system)
Y Align Weighting This is only used in 3 fiducial mode and sets a value determining where the Y axis
alignment should be optimized.
Minimum 0%
Maximum 100%
Increment 1%
Default 50% (see vision system)
Alignment Mode This parameter determines the mode used for board to screen alignment. The Non Vision
option is only available from the configuration file. Options available are:
2 fiducial; 3 fiducial.
Default 2 fiducial
Fiducial 1 X coordinate Distance of first fiducial from the right or left hand edge of the board (configuration
dependent).
Minimum 1mm
Maximum Board Length
Increment 0.1mm
Default 1mm
Fiducial 1 Y coordinate Distance of the first fiducial from the front edge of the board.
Minimum 1mm
Maximum Board Width
Increment 0.1mm
Default 1mm
Fiducial 2 X coordinate Distance of second fiducial from the right or left hand edge of the board (configuration
dependent).
Minimum 1mm
Maximum Board Length
Increment 0.1mm
Default 1mm
Fiducial 2 Y coordinate Distance of the second fiducial from the front edge of the board.
Minimum 1mm
Maximum Board Width
Increment 0.1mm
Default 1mm
Fiducial 3 X coordinate Distance of third fiducial from the right or left hand edge of the board (configuration
dependent).
Minimum 1mm
Maximum Board Length
Increment 0.1mm
Default 1mm
Software Version 6 User Manual 1.95
MACHINE PROGRAMMING
MENU PARAMETERS
Parameter Definition
Fiducial 3 Y coordinate Distance of the third fiducial from the front edge of the board.
Minimum 1mm
Maximum Board Width
Increment 0.1mm
Default 1mm
Select Mark X Distance of the select mark from the right or left hand edge of the board (configuration
dependent).
Minimum 0mm
Maximum Board Length
Increment 0.1mm
Default 148.5mm
NOTE
Only used while Selective Print/Pass is enabled in Set Preferences.
Select Mark Y Distance of the select mark from the front edge of the board.
Minimum 0mm
Maximum Board Width
Increment 0.1mm
Default 13mm
NOTE
Only used while Selective Print/Pass is enabled in Set Preferences.
Board 1 Fiducial Type This determines the type of model to be used for this fiducial. Options are Circle;
Rectangle; Diamond; Triangle; Double Square; Cross; Video model. (see vision system)
Board 2 Fiducial Type This determines the type of model to be used for this fiducial. Options are Circle;
Rectangle; Diamond; Triangle; Double Square; Cross; Video model. (see vision system)
Board 3 Fiducial Type This determines the type of model to be used for this fiducial. Options are Circle;
Rectangle; Diamond; Triangle; Double Square; Cross; Video model. (see vision system)
Select Mark Type This determines the type of model to be used on the board for the select mark. Options
are Circle; Rectangle; Diamond; Triangle; Double Square; Cross; Video model. (see
vision system)
NOTE
Only used while Selective Print/Pass is enabled in Set Preferences.
Screen 1 Fiducial Type This determines the type of model to be used for this fiducial. Options are Circle;
Rectangle; Diamond; Triangle; Double Square; Cross; Video model. (see vision system)
Screen 2 Fiducial Type This determines the type of model to be used for this fiducial. Options are Circle;
Rectangle; Diamond; Triangle; Double Square; Cross; Video model. (see vision system)
Screen 3 Fiducial Type This determines the type of model to be used for this fiducial. Options are Circle;
Rectangle; Diamond; Triangle; Double Square; Cross; Video model. (see vision system)
Screen Image The position of the image in the screen frame. Options available are EDGE justified and
CENTRE Justified. Edge justified only is permitted for Sanyo and Fuji frames.
NOTE
This parameter is not displayed, if Screen Size in Set Preferences has been selected to
Screen Library.
Custom Screen This option allows user definable screen image positions. Selection of this parameter
activates the Print Area Length, Print Area Width and Distance To Image. Options are:
ENABLED; DISABLED
NOTE
This parameter is not displayed, if Screen Size in Set Preferences has been selected to
Screen Library.
Distance To Image The meaning of this parameter varies, depending on whether an image is centre or edge
justified. For centre justified images, the dimension is the distance from the outside rear
of the screen frame to the centre of the image. For edge justified images, the dimension
is the distance from the outside rear of the screen frame to the front edge of the board.
NOTE
This parameter field only appears if Custom Screen has been selected.
Minimum 306mm
Maximum 645mm
Increments 0.1mm
1.96 User Manual Software Version 6
MACHINE PROGRAMMING
MENU PARAMETERS