Horizon UserManualV6 - 第113页

Parameter Definition Print Area Length This is the maximum printable distance in the Y direction, ie the maximum distance the squeegee can travel, front to back. NOTE This parameter field only appears if Custom Screen ha…

100%1 / 378
Parameter Definition
Fiducial 3 Y coordinate Distance of the third fiducial from the front edge of the board.
Minimum 1mm
Maximum Board Width
Increment 0.1mm
Default 1mm
Select Mark X Distance of the select mark from the right or left hand edge of the board (configuration
dependent).
Minimum 0mm
Maximum Board Length
Increment 0.1mm
Default 148.5mm
NOTE
Only used while Selective Print/Pass is enabled in Set Preferences.
Select Mark Y Distance of the select mark from the front edge of the board.
Minimum 0mm
Maximum Board Width
Increment 0.1mm
Default 13mm
NOTE
Only used while Selective Print/Pass is enabled in Set Preferences.
Board 1 Fiducial Type This determines the type of model to be used for this fiducial. Options are Circle;
Rectangle; Diamond; Triangle; Double Square; Cross; Video model. (see vision system)
Board 2 Fiducial Type This determines the type of model to be used for this fiducial. Options are Circle;
Rectangle; Diamond; Triangle; Double Square; Cross; Video model. (see vision system)
Board 3 Fiducial Type This determines the type of model to be used for this fiducial. Options are Circle;
Rectangle; Diamond; Triangle; Double Square; Cross; Video model. (see vision system)
Select Mark Type This determines the type of model to be used on the board for the select mark. Options
are Circle; Rectangle; Diamond; Triangle; Double Square; Cross; Video model. (see
vision system)
NOTE
Only used while Selective Print/Pass is enabled in Set Preferences.
Screen 1 Fiducial Type This determines the type of model to be used for this fiducial. Options are Circle;
Rectangle; Diamond; Triangle; Double Square; Cross; Video model. (see vision system)
Screen 2 Fiducial Type This determines the type of model to be used for this fiducial. Options are Circle;
Rectangle; Diamond; Triangle; Double Square; Cross; Video model. (see vision system)
Screen 3 Fiducial Type This determines the type of model to be used for this fiducial. Options are Circle;
Rectangle; Diamond; Triangle; Double Square; Cross; Video model. (see vision system)
Screen Image The position of the image in the screen frame. Options available are EDGE justified and
CENTRE Justified. Edge justified only is permitted for Sanyo and Fuji frames.
NOTE
This parameter is not displayed, if Screen Size in Set Preferences has been selected to
Screen Library.
Custom Screen This option allows user definable screen image positions. Selection of this parameter
activates the Print Area Length, Print Area Width and Distance To Image. Options are:
ENABLED; DISABLED
NOTE
This parameter is not displayed, if Screen Size in Set Preferences has been selected to
Screen Library.
Distance To Image The meaning of this parameter varies, depending on whether an image is centre or edge
justified. For centre justified images, the dimension is the distance from the outside rear
of the screen frame to the centre of the image. For edge justified images, the dimension
is the distance from the outside rear of the screen frame to the front edge of the board.
NOTE
This parameter field only appears if Custom Screen has been selected.
Minimum 306mm
Maximum 645mm
Increments 0.1mm
1.96 User Manual Software Version 6
MACHINE PROGRAMMING
MENU PARAMETERS
Parameter Definition
Print Area Length This is the maximum printable distance in the Y direction, ie the maximum distance the
squeegee can travel, front to back.
NOTE
This parameter field only appears if Custom Screen has been selected.
Minimum 100mm
Maximum 508.5mm
Increments 0.1mm
Print Area Width This is the maximum length of squeegee that could be fitted to the printer, taking into
account screen frame and the amount of mesh surrounding the mask. This is also the
maximum length of paste that can be dispensed.
NOTE
This parameter field only appears if Custom Screen has been selected.
Minimum 100mm
Maximum 510mm
Increments 0.1mm
Screen Adapter The type of screen adapter needed, if any, for the screen to be used for this product.
NOTE
This parameter is not displayed, if Screen Size in Set Preferences has been selected to
Screen Library.
Options available are NONE, 255, SANYO, HERAEUS, 20 X 20 and
12 X 12.
Forward X offset Programmable offset of the print on the board when printing from the rear. A positive
offset moves the print to the right of the board.
Minimum -1.0mm
Maximum +1.0mm
Increment 0.004mm
Forward Y offset Programmable offset of the print on the board when printing from the rear. A positive
offset moves the print to the rear of the board.
Minimum -1.0mm
Maximum +1.0mm
Increment 0.004mm
Forward q offset
Programmable offset of the print on the board when printing from the rear. A positive
offset moves the print in a clockwise direction.
Minimum -1000 arc seconds
Maximum +1000 arc seconds
Increment 2 arc seconds
Reverse X offset Programmable offset of the print on the board when printing from the front. A positive
offset moves the print to the right of the board.
Minimum -1.0mm
Maximum +1.0mm
Increment 0.004mm
Reverse Y offset Programmable offset of the print on the board when printing from the front. A positive
offset moves the print to the rear of the board.
Minimum -1.0mm
Maximum +1.0mm
Increment 0.004mm
Reverse q offset
Programmable offset of the print on the board when printing from the front. A positive
offset moves the print in a clockwise direction.
Minimum -1000 arc seconds
Maximum +1000 arc seconds
Increment 2 arc seconds
Print Mode This parameter sets the mode of operation of the machine. Available modes are:
PRINT/PRINT, PRINT/FLOOD, FLOOD/PRINT, ADHESIVE.
The default is PRINT/PRINT.
Selecting Adhesive from this parameter opens the separation delay and print vacuum
mode.
Software Version 6 User Manual 1.97
MACHINE PROGRAMMING
MENU PARAMETERS
Parameter Definition
Front Print Speed This parameter sets the speed across the screen when printing.
Minimum 2mm/sec
Maximum 150mm/sec
Increments 1mm/sec
Default 10mm/sec
Rear Print Speed This parameter sets the speed across the screen when printing.
Minimum 2mm/sec
Maximum 150mm/sec
Increments 1mm/sec
Default 10mm/sec
Front Pressure This parameter sets the force applied by the front squeegee during its print stroke.
Minimum 0kg
Maximum 20Kg
Increments 0.2Kg
Rear Pressure This parameter sets the force applied by the rear squeegee during its print stroke.
Minimum 0kg
Maximum 20Kg
Increments 0.2Kg
Print Gap This parameter sets the gap required between the screen and board to be printed during
the print stroke.
Minimum 0mm
Maximum 6mm
Increments 0.025mm
Knead Off-image This parameter sets whether ProFlow is to knead in an off-image area of the stencil.
Options are:
Enabled; Disabled
Default Enabled
Knead Before Printing This parameter sets ProFlow to knead before printing the first board and the amount of
boards to be printed between kneading.
Minimum 0 (disables knead before printing)
Maximum 100
Increment 1
Default 0
NOTE
This parameter is only displayed, if knead off-image is set to enabled.
Stencil Protection This parameter sets whether tooling to support the stencil, outside the board and clamp
envelopes, is in use. Options are:
Not Fitted; Fitted
Default Fitted
NOTE
This parameter is only displayed while ProFlow is fitted.
Separation Speed This parameter sets the speed at which the first 3mm of separation of board and screen
occurs.
Minimum 0.1mm/sec
Maximum 20mm/sec
Increments 0.1mm/sec
Separation Distance This parameter sets the separation distance between board and screen. The parameter can
help increase cycle time when a low separation speed is used by decreasing the
separation distance.
Minimum 0.0mm
Maximum 3.0mm
Increments 0.1mm
Default 3.0mm
Separation Delay This parameter is the time in seconds that the table delays before lowering. This delay
occurs during screen cleaning and after the flood. This parameter only becomes available
when Adhesive has been selected in the Print Mode parameter.
Print Deposits This parameter sets the number of consecutive print strokes carried out on one substrate.
Select 1, 2 or 3
Default 1
1.98 User Manual Software Version 6
MACHINE PROGRAMMING
MENU PARAMETERS