M2series_ServiceManual_e.pdf - 第43页

3 Mechanical Section 3-11 ■ Inspection of Suction Pad (Nozzle No. N017, N018, N019, N020) Check that the rubber suction pad located at t he nozzle tip is free of scratches and cracks. If they are found on the pad, replac…

3 Mechanical Section

3-10

④ Wind to fasten the wire between both sides of the nozzle cleaner assy.

(Part No. KV8-M8881-A0X)

Nozzle Cleaner

Assy.

⑤ Move the nozzle back and forth to clean the nozzle hole.

⑥ Remove the wire and blow some air into the nozzle hole.

■ Nozzle Cleaning using Wire (2)

You can use the wire by fastening the wire ends with adhesive tape. In this case, adhesive may remain on

the wire. So be sure to clean the wire end before pulling out the wire from the nozzle.

Adhesive Tape

3 Mechanical Section

3-11

■ Inspection of Suction Pad (Nozzle No. N017, N018, N019, N020)

Check that the rubber suction pad located at the nozzle tip is free of scratches and cracks. If they are found

on the pad, replace the pad with a new one.

ACTION: Remove the old pad, apply silicon grease to the inner surface of a new pad, and then install it in the nozzle.

NOTE: N020 has a different nozzle structure from those of N017 to N019. Thus, in the case of N020, remove the

pad stopper from the nozzle tip first and then remove the suction pad. After a new pad is installed, make

sure that the pad stopper is re-installed properly.

Nozzle N020

Suction pad

Pad stopper

(Can be removed by turning counter-clockwise

using a flat-blade screwdriver)

Part Name

Part No. Remark

RUBB.PAD17 LG0-M77A0-00X Suction pad for N017

RUBB.PAD18 LG0-M77A1-00X Suction pad for N018

RUBB.PAD19 LG0-M77A2-00X Suction pad for N019

RUBB.PAD20 LG0-M77A9-00X Suction pad for N020

PAD STOPPER M020 LG0-M770U-000 Pad stopper for N020/M020

GREASE SILICON LG0-M89AB-00X Silicone Grease

3 Mechanical Section

3-12

■ Applying Silicon Grease

After the nozzle is cleaned, it must be coated with silicon grease.

Apply silicon grease.

Nozzle ID sticker

Suction pad

● Nozzle outer surface

Apply a slight amount of grease to the outer surface (indicated by dotted lines in the above illustration), and

then wipe it off with a dry cloth.

NOTE: Silicon grease must be applied so that it forms a thin film on the surface.

● Suction pad

Application of oil content is needed to prevent deterioration of the rubber. Apply a slight amount of grease

to the outer surface of the suction pad, and then wipe it off with a dry cloth.

NOTE: Silicon grease must be applied so that it forms a thin film on the surface.

Do not apply excessive amounts of grease. This may cause collection of dirt

or dust in the air passage and on placed components, resulting in component

placement failure.

● Checking the nozzle escape

After grease is applied to the nozzle’s outer surface, attach the nozzle to the head and check the condition of

the nozzle escape.

NOTE: When the nozzle is placed in the head (nozzle holder), it can slide a few millimeters vertically. This nozzle

sliding movement is called nozzle escape.

ACTION:

① Attach the nozzle to the head.

② Push the nozzle gently with fingers up to the top dead center of the nozzle escape.

③ Release fingers gently and check that the nozzle returns to the lower dead center smoothly.

NOTE: If the nozzle escape is not smooth, there may be problems with component suction and placement. If the

nozzle gets caught or does not move smoothly, check the nozzle holder and nozzle’s inner/outer surfaces

for collection of foreign matter or scratches.