00197975-06_UM_TX-Serie_EN - 第164页
3 Technical data and assemblie s User manual SIPLACE TX-Series 3.8 SIPLACE tape feeder modules for SIPLACE TX-Series From softw are version 713.0 Edition 01/2020 164 3.8.4 Energy and dat a interface (EDIF) for X feeder m…
User manual SIPLACE TX-Series 3 Technical data and assemblies
From software version 713.0 Edition 01/2020 3.8 SIPLACE tape feeder modules for SIPLACE TX-Series
163
3.8.3.3 Restrictions
– The LDU-X module must be manually configured in the setup.
– You may configure a maximum of two LDU X modules per table for the SIPLACE TX-Series.
– An LDU X module in connection with JTF-ML
3.8.3.4 Dip plates for specified flux layer thicknesses
Dip plate depth Item no.
30 μm 00117023-xx
60 μm 00117026-xx
70 μm 00117027-xx
75 μm 00117021-xx
80 μm 00117028-xx
90 μm 00117029-xx
100 μm 00117030-xx
110 μm 00117038-xx
120 μm 00117031-xx
130 μm 00117039-xx
170 μm 00117054-xx
210 μm 00117042-xx
220 μm 00117032-xx
230 μm 00117033-xx
240 μm 00117037-xx
280 μm 00117034-xx
300 μm 00117041-xx
320 μm 00117035-xx
360 μm 00117036-xx
400 μm 00117040-xx
3 Technical data and assemblies User manual SIPLACE TX-Series
3.8 SIPLACE tape feeder modules for SIPLACE TX-Series From software version 713.0 Edition 01/2020
164
3.8.4 Energy and data interface (EDIF) for X feeder modules
Item no. 00141247-xx Energy and data interface for X feeder modules
3
Fig. 3.8 - 5 Energy and data interface for X feeder modules
(1) Unlocking button for locking latch
(2) Operator panel
(3) Data cable
(4) Power supply cable
(5) Electronics housing
(6) Fold-out feet
(7) Omega profile for guiding feeder modules
(8) Locking latch
(9) Locating hole for front centering pin of feeder module
(10) Base plate
(11) Tape reel holder
User manual SIPLACE TX-Series 3 Technical data and assemblies
From software version 713.0 Edition 01/2020 3.8 SIPLACE tape feeder modules for SIPLACE TX-Series
165
3.8.4.1 Description
The energy and data interface allows X feeder modules to be used outside the placement machine
and presetup area. The interface consists of an aluminum frame with omega profile for holding
and guiding the feeder modules. As with the component trolley, the feeder module is placed on
the omega profile, with the slider guides, and is pushed forwards until the front centering pin of the
feeder module is fully inserted into the locating hole. The locking latch locks the feeder module in
this position. To remove the feeder module, simply press the release button. The locking latch is
pressed downwards and releases the feeder module. Fold-out feet stabilize the position of the en-
ergy and data interface, particularly for wider feeder modules.
The electronics housing holds the electronic control unit for the energy and data interface. The
operating panel consists of start and stop buttons and two status LEDs. Communication with a PC
takes place via the data cable. The power supply cable is connected to the power supply unit pro-
vided.
3.8.4.2 Usage
The energy and data interface is used to check, maintain and repair X feeder modules. It can also
be used for setting up in advance for PCB production. In this case, the energy and data interface
is fixed to the base plate. The tape reel holder is also mounted on the base plate. When a com-
ponent tape is inserted, you can check or reset the increment, pick-up position and conveyor
speed. The detailed user manual describes how to use the interface and the necessary servicing
work.
3.8.4.3 Scope of delivery
– Single Slot EDIF
– Power supply, 100 - 120 / 200 - 240 VAC, +30VDC, 4.3 A
– Base plate with tape reel arm
– User manual