00197975-06_UM_TX-Serie_EN - 第217页

User manual SIPLACE TX-Series 4 Setting up and commissioning From software version 713.0 Edition 01/2020 4.6 Adjusting the com ponent trolley t o the PCB conveyor height 217 4.6.1 W arning instructions 4 4.6.2 T ools and…

4 Setting up and commissioning User manual SIPLACE TX-Series

4.6 Adjusting the component trolley to the PCB conveyor height From software version 713.0 Edition 01/2020

216

4.6 Adjusting the component trolley to the PCB conveyor

height

The component trolley can be easily and quickly adjusted to the following PCB conveyor heights:

900 mm 4

930 mm (standard height) 4

950 mm 4

Fig. 4.6 - 1 Component trolley

(1) Holes for the transport heights of 900, 930 and 950 mm.

(2) Changeover table

900 mm

930 mm

950 mm

(1)

(2)

User manual SIPLACE TX-Series 4 Setting up and commissioning

From software version 713.0 Edition 01/2020 4.6 Adjusting the component trolley to the PCB conveyor height

217

4.6.1 Warning instructions

4.6.2 Tools and equipment

You will need the following tools and equipment to adjust the height of the component trolley:

– Fit-up aid (item no. 03015976-xx)

– Lifting device for raising the component trolley table, carrying capacity at least 80 kg

4.6.3 Changing the component trolley height

 Fix the fit-up aid to the changeover table with the two M8 x 50 hexagon socket head screws.

 Hook the leverage device into the eyelet.

 Loosen the fixture pin and lift the changeover table into the required position.

 Insert the fixture pin into the hole for the required height.

 Dismantle the fit-up aid.

WARNING

Adjustment of component trolley height by certified persons!

Only ASM Assembly Systems GmbH&Co.KG engineers or qualified personnel are per-

mitted to adjust the component trolley height.

 Always follow the applicable accident prevention regulations.

 Remove all the feeder modules from the changeover table, if you want to adjust the

height of the changeover table.

WARNING

Risk of damage!

Lifting and lowering the changeover table can lead to deformation of it.

 Remove all the feeder modules from the changeover table.

 Fit the fit-up aid to the changeover table in order to adjust the height.

4 Setting up and commissioning User manual SIPLACE TX-Series

4.7 Commissioning the placement machine From software version 713.0 Edition 01/2020

218

4.7 Commissioning the placement machine

4.7.1 Commissioning the placement machine at the customer's premises

 Check all modules for correct seating.

 Remove the shipping braces (see section 4.6, page 216).

 Wipe the linear guide rails of the X/Y axis with a lint-free cloth. Do not use any solvents (see

section 4.6

, page 216).

 Switch on the placement machine and perform a reference run.

 For SIPLACE TX micron: Perform an ACT as accuracy check, in accordance with ASM guide-

lines. See also the user manual for the ACT (Accuracy Checking Tool) - item no. 00196351-

xx.

 Load a recipe in the computer and test it.

 Check the machine zero point after a period of warming up of 3 - 4 h.

 Get the customer's operating personnel to equip the feeder modules according to the cus-

tomer's placement program.

 Instruct them in handling the feeder modules using the JobGuide.

 Check all customer-specific installed options (in particular software) for good functioning and

order any necessary spare parts using the order form or by fax.

4.7.2 Checking and setting the protective cover switch

 Check the function of the protective cover switch (see 2.4.1 on page 63).

 Adjust the protective cover switch if necessary (see service manual).