00197975-06_UM_TX-Serie_EN - 第276页

5 Tasks at the placement machi ne User manual SIPLACE TX-Series 5.14 Docking the component trolley in or out From software versi on 713.0 Edition 01/2020 276 5.14.3 Safety instructions for m oving the co mponent trolley …

User manual SIPLACE TX-Series 5 Tasks at the placement machine

From software version 713.0 Edition 01/2020 5.14 Docking the component trolley in or out

275

5.14.2 Docking the component trolley

 Carefully push the component trolley into the placement machine as far as the stop.

 Press the button on the respective placement machine location until the trolley is completely

docked in.

CAUTION

Pushing in component trolley!

 When pushing the component trolley into the placement machine, make sure that

you do not hit obstacles with the locking latches.

PLEASE NOTE

Cut tapes flush

If you do not cut tapes off flush at the front end of the X feeder modules, the emptied

tapes will not enter the empty tape duct.

 Cut the tapes off flush, before you dock the component trolley into place.

CAUTION

Position of placement head!

Check that the placement head is outside the range of the component trolley.

5 Tasks at the placement machine User manual SIPLACE TX-Series

5.14 Docking the component trolley in or out From software version 713.0 Edition 01/2020

276

5.14.3 Safety instructions for moving the component trolley

 Always hold the handles with both hands when you want to move the component trolley.

 Remember that a component trolley with the full complement of feeder modules can tip over

sideways or forward on gradients of 20° or more.

 Make sure that the surface on which the trolley is moved has a significantly smaller gradient.

 Be careful not to collide with obstacles. The trolley could tip forward if it is traveling fast

enough.

5.14.4 Docking out the component trolley

 Switch the control system "Off".

 Press the button on the respective placement machine location until the component trolley is

completely undocked.

 With both hands on the handles, pull the component trolley out of the placement machine.

WARNING

Avoid accidents!

To prevent accidents, ALWAYS follow the rules listed below when you move the compo-

nent trolley.

User manual SIPLACE TX-Series 6 Station extensions

From software version 713.0 Edition 01/2020 6.1 Nozzle changer

277

6 Station extensions

For the relevant configurations and other options, refer to the individual specifications for the SI-

PLACE placement machines.

6.1 Nozzle changer

6.1.1 General

Nozzle changers can greatly increase the flexibility of the placement heads for processing differ-

ent types of component. If the placement program requires a nozzle change, then the placement

head automatically returns the old nozzle to the nozzle holder and picks up the new nozzle. Noz-

zles that were separated out during the vacuum check can also be quickly changed. It is signifi-

cantly more exact and faster to pick up nozzles from a nozzle changer than would be possible

manually. When placing small components, it is essential to minimize the radial eccentricity during

nozzle rotation.

6.1.2 Nozzle changer for SIPLACE SpeedStar C&P20 P /M2

This nozzle changer can accommodate 4 magazines, each with 20 nozzle garages. The maga-

zines are seated on a common support. They are centered with two parallel pins and fixed in place

with 4 push buttons. The exact position is determined with two fiducials on each magazine. The

correct seat of the magazines on the basic nozzle changer body is monitored by microswitches,

to prevent a collision of the placement head with any magazines projecting upwards. All magazine

locations must be filled since the safety circuit stops the placement machine in response to miss-

ing magazines or magazines that are not seated correctly. At the installed nozzle station, compo-

nents can be blown off the nozzles of the SpeedStar and nozzles stripped off and rejected.

CAUTION

 Only use the nozzle changer together with the SpeedStar.