00197975-06_UM_TX-Serie_EN - 第93页
User manual SIPLACE TX-Series 2 Operational safety From software version 713.0 Edition 01/2020 2.5 Safety features 93 2.5.4 Hand guards at the lo cations with dummy feeders 2 Fig. 2.5 - 7 Hand guard on the component trol…
2 Operational safety User manual SIPLACE TX-Series
2.5 Safety features From software version 713.0 Edition 01/2020
92
2.5.3.2 Enabling the EMERGENCY STOP
If problems occur, the SIPLACE TX can be stopped by pressing the EMERGENCY STOP button.
An EMERGENCY STOP can be triggered by:
– Pressing one of the EMERGENCY STOP buttons on the placement machine
In these cases, the safety cutoffs are triggered and the power contactors will be switched off within
100 ms or 500 ms (STOP category 1, controlled shutdown with interruption of power supply during
downtime).
2.5.3.3 Resetting an EMERGENCY STOP
To reset an EMERGENCY STOP, unlock the EMERGENCY STOP button.
Find out the reason why the EMERGENCY STOP button triggered.
Remove the cause.
Unlock the relevant EMERGENCY STOP button.
2.5.3.4 Resetting the lock
Close the open protective cover.
2.5.3.5 Triggering the lock
Opening the protective cover.
User manual SIPLACE TX-Series 2 Operational safety
From software version 713.0 Edition 01/2020 2.5 Safety features
93
2.5.4 Hand guards at the locations with dummy feeders
2
Fig. 2.5 - 7 Hand guard on the component trolley locations
2
(1) Dummy feeder SIPLACE X, item no. 00141226-xx
WARNING
Operational
Operational safety by occupying every second location!
The operational safety of the component trolley in the SIPLACE TX is ensured if at least
every second free location is occupied with a feeder module or hand guard (dummy feed-
er).
Fit a hand guard at locations 1 and 2.
Even when configuring a holder for waffle pack trays, secure every second location
with a hand guard.
2 Operational safety User manual SIPLACE TX-Series
2.6 Residual voltages and discharge times in the placement machine From software version 713.0 Edition 01/2020
94
2.6 Residual voltages and discharge times in the place-
ment machine
If the EMERGENCY STOP button is pressed or the placement machine is switched off, the 300
V- intermediate circuit voltage for the gantry axes and the 160 V- intermediate circuit voltage for
the star and Z axes will be reduced to harmless residual voltages within a very short time.
2
2.6.1 Energy state of the placement machine after switching off at the main power
switch
2
DANGER
Dangerous voltage levels!
The placement machine is supplied with 3 x 380 V~ to 3 x 415 V ± 10 %, 50/60 Hz or op-
tionally with 3 x 200 V~ to 3 x 220 V~ ± 10 %; 50/60 Hz mains voltage. Due to the use of
energy storage capacitors, parts of the system may conduct hazardous voltages for a cer-
tain time (approx. 5 minutes) even when the main switch has been switched off and the
mains plug has been disconnected.
Incorrect handling of this placement machine can therefore result in death or severe injury
or considerable damage to equipment.
Always follow the applicable accident prevention and DIN regulations (particularly EN
60204, part 1 or IEC 60204, part 1) and the applicable regulations in your own coun-
try.
The covers over the power supply unit may ONLY be opened by appropriately qual-
ified and trained personnel.
DANGER
Lethal voltages in the power supply unit!
The power supply unit has components (capacitors) which can still conduct potentially le-
thal voltages for approx. 5 minutes, even when the placement machine has been switched
off and the mains plug has been disconnected.
Wait at least 5 minutes before you perform work on the power supply unit.
Only ASM Assembly Systems GmbH&Co.KG service engineers or the machine
owner's service engineers, who have been trained by ASM, may perform work on the
power supply and the safety cutoff (CBS).