00192809-01 - 第37页
User Manual V 1.15 - P roductivity Lift 3 Assembling and installing Software version V 40. 1 1 Edition 01/2001 3.4 Installation / Reinstallation of emergency conv eyor 29 6WR SRIHPHUJHQF \FRQY H\RU 7 R VWRS WK…
3 Assembling and installing User Manual V 1.15 - Productivity Lift
3.3 Switching the device on Software version V 40.11 Edition 01/2001
28
6ZLWFKLQJWKHGHYLFHRQ
Once the device has been switched on at the main switch, an emergency stop message appears
in the display, which must be confirmed using the "Enter" key. This will set the device to the stand-
by-operating mode.
Pressing the "Start" key sets the device to the automatic operating mode, which begins by running
an initialisation phase. This serves to test basic system functions.
Following this brief initialisation, the device is set to the automatic operating mode and is ready to
operate.
,QVWDOODWLRQ5HLQVWDOODWLRQRIHPHUJHQF\FRQYH\RU
The emergency conveyor is used, when the shuttle is not in use e.g. for reasons of maintenance.
,QRUGHUWRDFWLYDWHWKHHPHUJHQF\FRQYH\RUGRWKHIROORZLQJ
1. By pushing the "stop" cursor the corresponding conveyor is put into stand-by mode.
2. Through "ALT" cursor the adjustment mode comes up.
3. Through the "Enter" cursor the menu comes up on the display which shows "PCB takeover"
comes up and you can check if the adjustment is "dual lane". If this is not the case one can
switch to "dual lane" as described in the chapter 6.3.
4. Use the "enter" cursor. The menu "PCB transfer" comes up. Here it is the same procedure as
described in point 3 (see chapter "6.6").
5. Another use of the "enter" cursor brings up the menu "PCB pass-through". In this menu the
emergency conveyor can be switched on by choosing the adjustment "switched on" (see chap-
ter "6.7"). This change can be taken over with the "enter" cursor.
6. The adjustment mode can be quit with the "stop" cursor.
If the machine is started now the lift conveyor drives down and the emergency conveyor lowers to
the operating position and starts itself. Afterwards the device is again in operation mode.
User Manual V 1.15 - Productivity Lift 3 Assembling and installing
Software version V 40.11 Edition 01/2001 3.4 Installation / Reinstallation of emergency conveyor
29
6WRSRIHPHUJHQF\FRQYH\RU
7RVWRSWKHHPHUJHQF\FRQYH\RUWKHSURFHGXUHGHVFULEHGDERYHKDVWREHPDGHWKHRWKHU
ZD\URXQG
1. By pushing the "stop" cursor the corresponding conveyor is put into stand-by mode.
2. Through "ALT" cursor the adjustment mode comes up.
3. Through the "Enter" cursor the menu comes up on the display which shows "PCB takeover"
comes up and you can chose the adjustment as used before the emergency conveyor (see
chapter "6.3").
4. Use the "enter" cursor. The menu "PCB transfer" comes up. Here it is the same procedure as
described in point 3 (see chapter "6.6").
5. Another use of the "enter" cursor brings up the menu "PCB pass-through". In this menu the
emergency conveyor can be switched off by choosing the adjustment "switched off" (see chap-
ter "6.7"). This change can be taken over with the "enter" cursor.
6. The adjustment mode can be quit with the "stop" cursor.
The device can be started with the "start" cursor. After an initialising time the device is ready for
operation.
127(
Pay attention that the changes made in chapter 6.3 and 6.6 are set back to the adjustments as
before activated.
3 Assembling and installing User Manual V 1.15 - Productivity Lift
3.4 Installation / Reinstallation of emergency conveyor Software version V 40.11 Edition 01/2001
30