00196062-03_SM_LDU-X_EN - 第19页
4 Service Work 4.2 Replacing Spare Parts Service Manual SIPLACE LDU-X Linear Dipping Unit 11/2017 19 4.2 Replacing Spare Parts 4.2.1 List of Spare Parts The following spare parts are available for the LDU-X: Item no. Des…
4 Service Work
4.1 Single Slot EDIF
18 Service Manual SIPLACE LDU-X Linear Dipping Unit 11/2017
4.1.1 Placing the LDU-X on the Single Slot EDIF
► Place the LDU-X on the Single Slot
EDIF.
► Push the LDU‑X up to the end stop in
the track.
► Press the LDU‑X firmly against the
stop, so that the LDU‑X engages at
the front. The LDU-X will automatic-
ally switch itself on when the power
pack is connected.
CAUTION
Automatic reference run
If the key switch is set to PRODUCTION, the LDU-X will automatically perform a reference
run once it has been switched on.
Make sure that the axes move freely for the reference run.
4.1.2 Removing the LDU-X from the Single Slot EDIF
► Press the locking button on the SSE
down.
The LDU‑X can now be pushed from
behind and taken off the SSE.
4 Service Work
4.2 Replacing Spare Parts
Service Manual SIPLACE LDU-X Linear Dipping Unit 11/2017 19
4.2 Replacing Spare Parts
4.2.1 List of Spare Parts
The following spare parts are available for the LDU-X:
Item no. Designation
03060794-xx Flux tank, standard
03110865-xx Flat module plug-in board / EDIF secondary IrDA board
03032819-xx Cable IrDa - EDIF secondary
03069261-xx Flat module plug-in board / control board for X adapter
03128818-xx Rear slide bearing assembly
03128490-xx Slide bearing, LDU version
03134341-xx LDU-X robustness V2 kit
03132870-xx Stop pin/X-Series modified
03128482-xx Support X16-88, metal version
03011739-xx Energy and data interface (EDIF) assembly/X-Series
03012683-xx Pressure spring D-027
03050957-xx Collar screw D4x3.15 M3
03055413-xx Display board
03063561-xx Display foil
03062342-xx Service switch
03062334-xx Emergency stop switch
03062897-xx LDU-X control board
03059486-xx Coupling
03059241-xx Dip tray
03059479-xx Motor with gearing and encoder
03068930-xx Proximity switch assembly
03071772-xx Downholder assembly
03023240-xx ISO 7046-2-M3 x 10-A2-70-H (2x)
03062471-xx Handle
03007733-xx ISO4762–M3x6-8.8, galvanized
03062390-xx Side plate, left
03062033-xx Cover panel with screws
03062032-xx Flap assembly
03062461-xx Cover
03063497-xx Cable X adapter - control board
03066594-xx Cable display board - control board
4.2.2 Important Information for Replacing Spare Parts
► Use ESD-proof tools at an ESD-proof workplace.
► Make sure that no flux is left in the LDU-X during this service work.
► Before performing any service work, remove all parts which are not fixed to the LDU-X.
- Flux tank
- Dip plate
- Park plate
- Dip tray
- Top cover
► Always perform a function check after any service work.
4 Service Work
4.2 Replacing Spare Parts
20 Service Manual SIPLACE LDU-X Linear Dipping Unit 11/2017
4.2.3 Replacing the Flux Tank
Overview
Flux tank [03060794-xx]
Equipment required
●
Standard tools
●
Spare part: Flux tank standard [03060794-xx]
Removal
► Unlock the downholder and swing it up.
► Remove the flux tank.
Installation
► Fit the new flux tank into place.
Check that three pins are positioned at the right side of the flux tank.
► Swing the downholder down again and lock it.
► Check the flux tank for correct positioning.
4.2.4 Replacing the IrDA Board
Overview
Flat module plug-in board EDIF secondary IrDA
board [03110865-xx] with flat ribbon cable
1. Flat module plug-in board EDIF sec-
ondary IrDA board
2. Flat ribbon cable to control board for
X adapter