00193411-02 - 第136页

6 Component handling User Manual SIPLACE HS-60 6.2 Technical data f or the feeders Software v ersion SR.503.xx 07/2003 US Edition 136 6.2.8 Bulk ca se fee der 6 Fig. 6.2 - 8 Bulk ca se feeder 6 Item no. 00142 318-xx 6 Wi…

User Manual SIPLACE HS-60 6 Component handling

Software version SR.503.xx 07/2003 US Edition 6.2 Technical data for the feeders

135

6.2.7 24/32 mm S feeder

Fig. 6.2 - 7 24/32 mm S feeder

Item no. 00141093-xx 6

Wide 42.4 mm 6

Tracks per feeder 1 6

Assigned locations 1.5 6

Maximum number of feeders 4 x 8 6

Stock of components for 7" reels approx. 2000 6

Transport distance (variable) 4 to 40 mm, (in 4 mm increments) 6

6 Component handling User Manual SIPLACE HS-60

6.2 Technical data for the feeders Software version SR.503.xx 07/2003 US Edition

136

6.2.8 Bulk case feeder

Fig. 6.2 - 8 Bulk case feeder

Item no. 00142318-xx 6

Wide 29 mm 6

Tracks per feeder 2 6

Assigned locations 1 6

Maximum number of feeders 4 x 12 6

Stock of components up to 50,000 6

Feeding rails 0402 / 0.35 mm high item no. 00142319-xx 6

0402 / 0.5 mm high item no. 00142320-xx 6

0603 / 0.45 mm high item no. 00142321-xx 6

0603 / 0.80 mm high item no. 00142322-xx 6

0805 / 0.45 mm high item no. 00142323-xx 6

0805 / 0.60 mm high item no. 00142324-xx 6

0805 / 0.85 mm high item no. 00142325-xx 6

0805 / 1.25 mm high item no. 00142326-xx 6

Micro Melf / 1.05 ± 0.05 mm item no. 00142327-xx 6

Mini Melf / 1.40 ± 0.1 mm item no. 00142328-xx 6

Cycle time < 60 ms 6

User Manual SIPLACE HS-60 6 Component handling

Software version SR.503.xx 07/2003 US Edition 6.3 Setting up the feeders

137

6.3 Setting up the feeders

6.3.1 Preparing the component table and feeders for set-up

Æ Select the adjustment range for the feeders to be used.

Æ Move the placement head to the waiting position and press the emergency stop button.

Æ Open the protective covers.

Æ Clean the contact surface for the feeders and the contact surface for the feeders on the com-

ponent table.

Æ Place the feeder on the previously selected track on the component table (see Vibrator config-

uration).

6.3.2 Inserting the feeder

Æ Insert the feeder so that the back of the feeder is held by the centering ball and the front is fixed

in place by the corresponding centering pin on the component table. Make sure that the feeder

is placed on the component table in the correct position for its width.

Æ Check that the feeder is firmly seated on the component table.

Æ Connect the feeder plug to the socket beneath the location.

PLEASE NOTE 6

When you connect the feeder, make sure that you use the right socket for the location since

the feeder receives the control pulse via this socket. The feeder may not work correctly if it

is not connected to the right socket. 6

Æ Close the protective covers and switch the control on again.

Æ Carry out a refill check if necessary.

Æ Continue placement.