M20_Ope_E - 第443页

1049 MIN,%d6, EDGE_NUM: %d1/%d8 %m T axes didn't travel to the position for nozzle Motor/ANC error. Check the error phenomenon and 1015 exchange. Head%s %d2:%d3(%d6>%d4) ANC(%d5) contact us. Check the motor error…

1014 Image data results of Debris check could not be Check the destination to save image data is proper.

960

961

%s Elevator height error for tray transfer.

%s Elevator position sensor does not respond.

Tray may have not reached transfer height properly.

Check Elevator height detect sensor and Elevator

962 %s No trays on Tray feed table

motion.

Tray may not have come out from Feed tray rack

properly.

963 %s No trays on Tray dump table. Tray may not have transferred properly.

964 %s Tray is on Shuttle unit. Tray may not have transferred properly.

965 %s Feed tray transfer error Check Feed tray at the transfer point.

966 %s Full trays in Dump tray rack. Take out empty trays from Dump tray rack. (Max.30)

967 %s Full trays in Feed tray rack. Take out trays from Feed tray rack. (Max.30)

968 %s Tray is on Tray feed table. Feed tray may not have transferred completely.

969 %s Tray is on Tray dump table. Dump tray may not have transferred properly.

970

971

%s Position error

%s Hook position error for Elevator drive

System parameter may be incorrect.

Check Hook origin detect sensor or Hook transfer

972 %s Elevator height error for Shuttle transfer.

motion.

Check Elevator height detect-sensor or Elevator

drive motion.

973

974

%s Tray is on Shuttle unit.

%s Shuttle unit is not ready at Pickup point.

Tray may not have transferred properly.

While preparation of tray feeding, error may have

occurred.

975 %s Time out for Tray feed table Up Check Tray feed table.

976 %s Time out for Tray feed table Down Check Tray feed table.

977 %s Time out for Tray dump table Up Check Tray dump table.

978 %s Time out for Tray dump table Down Check Tray dump table.

979 %s Time out for Tray stopper of Feed rack Unlock. Check Tray stopper.

980 %s Time out for Tray stopper of Feed rack Lock. Check Tray stopper.

981 %s Time out for Rack cover Lock. Check Rack cover lock.

982 %s Time out for Rack cover Unlock. Check Rack cover lock.

983 %s Time out for Feed tray push-lever On Check Feed tray push lever.

984 %s Time out for Feed tray push-lever Off. Check Feed tray push lever.

985 %s Time out for Dump tray push-lever On. Check Dump tray push lever.

986 %s Time out for Dump tray push-lever Off. Check Dump tray push lever.

987 %s Shuttle tray unlock Time out Check Shuttle tray lock.

988 %s Shuttle tray lock Time out Check Shuttle tray lock.

989 %s Hook origin Time out Check Hook.

990 %s Elevator origin Time out Check Elevator.

991 %s Hook transfer Time out Check Hook.

992 %s Elevator drive Time out Check Elevator.

993 %s Feed tray unload error Error happened while tray transfers to Tray feed

994 %s Dump tray stack error Error happened while tray transfers to Tray dump

995 %s Tray exchange interlock error. Interlock error is detected during tray exchange.

996 Undefined Vis-error Code

997 Control Message Code Error %d8

998 MT-LOG component name %m

999 Internal Error 999 Contact us.

1000 Emergency stop. %s Remove the cause of the error.

1001 Instantaneous power failure is detected. Check capacity of power source.

1002 Power failure

1003 Safety area sensor responded. Remove the obstruct in the sensing area.

Check the cover lock mechanism and the open cover

1004 Open %s was detected in the AUTO mode.

sensors.

1005 Air pressure is low.

%s Abnormal temperature of regenerative resistor is

Check the air connector on the machine rear side.

Check the temperature of the regenerative resistor

1006

detected. and cables for breaks.

Check the AUTO/MANUAL switch or others to

1007 Servo OFF signal was detected.

CFB or CTF is not connected in %s. Connect CTF or

eliminate the cause for Servo OFF.

1008

CFB by DOCKING SWITCH.

Elevator axis belt of the FTF exceeds the belt slack

Connect CTF or CFB by DOCKING SWITCH.

1009

tolerance.

Motor/mechanical error. Check the axis coordinates

1010 Detected the %c6%s axis end limit (+).

and contact us.

Motor/mechanical error. Check the axis coordinates

1011 Detected the %c6%s axis end limit (-).

and contact us.

1012 Request MMI Condition Check!!

An error is detected by IO operation. Check the error

1013 IO error is detected. %e

phenomenon and contact us.

1049

MIN,%d6, EDGE_NUM: %d1/%d8 %m

T axes didn't travel to the position for nozzle Motor/ANC error. Check the error phenomenon and

1015

exchange. Head%s %d2:%d3(%d6>%d4) ANC(%d5) contact us.

Check the motor error, nozzle status, or component

1016 Interlock worked while S axis was moving.

Z axis didn't reach the lowest position for nozzle

height.

Motor/ANC error. Check the error phenomenon and

1017

1018

exchange. Head%s %d2:%d3(%d6>%d4) ANC(%d5)

Nozzle was detected on the head by suction pressure

Manual Nozzle set on head caused mismatch status

with Nozzle info. Or problem of suction pressure

inspection when nozzle was mounted to the head.

XY axes didn't travel to the position for nozzle

measuring circuit.

Motor/ANC error. Check the error phenomenon and

1019

exchange. Head%s%c1 %d2:%d3(%d6>%d4) ANC(%d5)

T axes didn't travel to the position for nozzle

Motor/ANC error. Check the error phenomenon and

1020

exchange. Head%s %d2:%d3(%d6>%d4) ANC(%d5)

Head1 interlock worked while XY axes are moving

Error at the head actuators/motors. Check the head

1021

(head height: %d1 < %d2).

Head2 interlock worked while XY axes are moving

height and contact us.

Error at the head actuators/motors. Check the head

1022

(head height: %d1 < %d2).

Head3 interlock worked while XY axes are moving

height and contact us.

Error at the head actuators/motors. Check the head

1023

(head height: %d1 < %d2).

Head4 interlock worked while XY axes are moving

height and contact us.

Error at the head actuators/motors. Check the head

1024

(head height: %d1 < %d2).

Head5 interlock worked while XY axes are moving

height and contact us.

Error at the head actuators/motors. Check the head

1025

(head height: %d1 < %d2).

Head6 interlock worked while XY axes are moving

height and contact us.

Error at the head actuators/motors. Check the head

1026

(head height: %d1 < %d2).

Head%c6 interlock worked while XY axes are moving

height and contact us.

Error at the head actuators/motors. Check the head

1027

(%c4 %c5: %d1 > %d2).

Head%c6 interlock worked while XY axes are moving

height and contact us.

Error at the head actuators/motors. Check the head

1028

(head height: %d1 < %d2). height and contact us.

Remove the cause of the sensor interruption and

1029 CX axis cannot operate because %s is ON.

restart.

This error is caused by effect of other errors. Check

1030 Timeout in completing immediate stop

the other error messages near around.

This error is caused by effect of other errors. Check

1031 Motion-complete stop sequence error

the other error messages near around.

This error is caused by effect of other errors. Check

1032 Timeout in completing Cancel process

The placement correction value has exceeded the

the other error messages near around.

Computing error for correction. Save Log file and

1033

limit. (X: %d1->%d2 Y: %d3->%d4) contact us.

%s motion of the Docking Station did not finish. (%c1-

1034

%c2-%c3 : %c4)

%c1 switch cannot be activated. Because CFB or CTF

1035

1036

is not connected in %s.

The component picked up by Head%s exceeds the

Pickup tolerance.(Tolerance:%d1 Offset X:%d2 Y:%d3

Connect CTF or CFB by DOCKING SWITCH.

Check the pickup coordinates.

1037

T:%d4 %c5-%d6 Step:%d7 Offset:%d8 %m )

The components picked up by Head%s and Head %c1

possibly hit each other while correcting their pickup Check the components.

angles.( %d2 < %d3 Step:%d4 Offset:%d5 %m )

%s The production cannot start because the Feed Remove the bottom tray from the Feed Rack and

1038

Tray Push Lever is in an abnormal position. resume the production.

1039 Measure nozzle height offset error Please check nozzle condition.

1040 Error occurred while the conveyor actuator worked.

Error occurred while the Automatic-conveyor-width-

Check the actuator.

1041

adjustment actuator worked.

Check the conveyor.

1042 %s is %c1. ( ID: %d2 )

Conveyor interlock error is detected while XY axes

1043

are traveling.(%s:%c3)%c4

Check the conveyor status and the related sensors.

Check the control unit and press the READY switch

1044 Control unit %s error.(%i1:%c2)

again.

1045 Discharge height error Check the board.

1046 Dispense error recheck ( %s Step:%d1 Offset:%d2 )

Interlock error is detected during %o1

1047

works.(%c2:Y:%d4 != %d5)

Measure result: %s, AVE,%d4, DEV,%d7, MAX,%d5,

1048

MIN,%d6, CENTER %c2,%d3, EDGE_NUM: %d1/%d8 %m

Measure result: %s%c2, AVE,%d4, DEV,%d7, MAX,%d5,