M20_Ope_E - 第444页
1083 Servo OFF signal was detected. eliminate the cause for Servo OFF. Error at servomotors or power source. Check the 1050 Servomotors alarm at %s (alarm code:%d1) alarm code and contact us. Error at servomotors or powe…
1049
MIN,%d6, EDGE_NUM: %d1/%d8 %m
T axes didn't travel to the position for nozzle Motor/ANC error. Check the error phenomenon and
1015
exchange. Head%s %d2:%d3(%d6>%d4) ANC(%d5) contact us.
Check the motor error, nozzle status, or component
1016 Interlock worked while S axis was moving.
Z axis didn't reach the lowest position for nozzle
height.
Motor/ANC error. Check the error phenomenon and
1017
1018
exchange. Head%s %d2:%d3(%d6>%d4) ANC(%d5)
Nozzle was detected on the head by suction pressure
contact us.
Manual Nozzle set on head caused mismatch status
with Nozzle info. Or problem of suction pressure
inspection when nozzle was mounted to the head.
XY axes didn't travel to the position for nozzle
measuring circuit.
Motor/ANC error. Check the error phenomenon and
1019
exchange. Head%s%c1 %d2:%d3(%d6>%d4) ANC(%d5)
T axes didn't travel to the position for nozzle
contact us.
Motor/ANC error. Check the error phenomenon and
1020
exchange. Head%s %d2:%d3(%d6>%d4) ANC(%d5)
Head1 interlock worked while XY axes are moving
contact us.
Error at the head actuators/motors. Check the head
1021
(head height: %d1 < %d2).
Head2 interlock worked while XY axes are moving
height and contact us.
Error at the head actuators/motors. Check the head
1022
(head height: %d1 < %d2).
Head3 interlock worked while XY axes are moving
height and contact us.
Error at the head actuators/motors. Check the head
1023
(head height: %d1 < %d2).
Head4 interlock worked while XY axes are moving
height and contact us.
Error at the head actuators/motors. Check the head
1024
(head height: %d1 < %d2).
Head5 interlock worked while XY axes are moving
height and contact us.
Error at the head actuators/motors. Check the head
1025
(head height: %d1 < %d2).
Head6 interlock worked while XY axes are moving
height and contact us.
Error at the head actuators/motors. Check the head
1026
(head height: %d1 < %d2).
Head%c6 interlock worked while XY axes are moving
height and contact us.
Error at the head actuators/motors. Check the head
1027
(%c4 %c5: %d1 > %d2).
Head%c6 interlock worked while XY axes are moving
height and contact us.
Error at the head actuators/motors. Check the head
1028
(head height: %d1 < %d2). height and contact us.
Remove the cause of the sensor interruption and
1029 CX axis cannot operate because %s is ON.
restart.
This error is caused by effect of other errors. Check
1030 Timeout in completing immediate stop
the other error messages near around.
This error is caused by effect of other errors. Check
1031 Motion-complete stop sequence error
the other error messages near around.
This error is caused by effect of other errors. Check
1032 Timeout in completing Cancel process
The placement correction value has exceeded the
the other error messages near around.
Computing error for correction. Save Log file and
1033
limit. (X: %d1->%d2 Y: %d3->%d4) contact us.
%s motion of the Docking Station did not finish. (%c1-
1034
%c2-%c3 : %c4)
%c1 switch cannot be activated. Because CFB or CTF
1035
1036
is not connected in %s.
The component picked up by Head%s exceeds the
Pickup tolerance.(Tolerance:%d1 Offset X:%d2 Y:%d3
Connect CTF or CFB by DOCKING SWITCH.
Check the pickup coordinates.
1037
T:%d4 %c5-%d6 Step:%d7 Offset:%d8 %m )
The components picked up by Head%s and Head %c1
possibly hit each other while correcting their pickup Check the components.
angles.( %d2 < %d3 Step:%d4 Offset:%d5 %m )
%s The production cannot start because the Feed Remove the bottom tray from the Feed Rack and
1038
Tray Push Lever is in an abnormal position. resume the production.
1039 Measure nozzle height offset error Please check nozzle condition.
1040 Error occurred while the conveyor actuator worked.
Error occurred while the Automatic-conveyor-width-
Check the actuator.
1041
adjustment actuator worked.
Check the conveyor.
1042 %s is %c1. ( ID: %d2 )
Conveyor interlock error is detected while XY axes
1043
are traveling.(%s:%c3)%c4
Check the conveyor status and the related sensors.
Check the control unit and press the READY switch
1044 Control unit %s error.(%i1:%c2)
again.
1045 Discharge height error Check the board.
1046 Dispense error recheck ( %s Step:%d1 Offset:%d2 )
Interlock error is detected during %o1
1047
works.(%c2:Y:%d4 != %d5)
Measure result: %s, AVE,%d4, DEV,%d7, MAX,%d5,
1048
MIN,%d6, CENTER %c2,%d3, EDGE_NUM: %d1/%d8 %m
Measure result: %s%c2, AVE,%d4, DEV,%d7, MAX,%d5,
1083 Servo OFF signal was detected.
eliminate the cause for Servo OFF.
Error at servomotors or power source. Check the
1050 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1051 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1052 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1053 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1054 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1055 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1056 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1057 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1058 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1059 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1060 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1061 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1062 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1063 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1064 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1065 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1066 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1067 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1068 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1069 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1070 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1071 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1072 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1073 Servomotors alarm at Head%c6 %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1074 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1075 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1076 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1077 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1078 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1079 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1080 Servomotors alarm at %s (alarm code:%d1)
alarm code and contact us.
Error at servomotors or power source. Check the
1081 Servomotors alarm at %s (alarm code:%d1)
Changed to safety stop" state because %s was
alarm code and contact us.
To resume production run, close the cover and press
1082
opened." the Servo switch.
Check the AUTO/MANUAL switch or others to
1127
(%d2-%d3)
Origin discrepancy between %c6%s dual axes %d1 <
Servomotors alarm at Head%c1 %s (alarm Error at servomotors or power source. Check the
1084
code:%d2(%d4) %e)
Servomotors alarm at %c1 %s (alarm code:%d2(%d4)
alarm code and contact us.
Error at servomotors or power source. Check the
1085
%e) alarm code and contact us.
Mark recognition for Camera coordinate correction
1086
cannot be performed. ( %s%c2 %c1 %m )
1087 The entrance sensor turns ON. Remove the PCB from the conveyor.
1088 Switched to Image Re-edit mode.
1089 The feeder is removed. %s %d1 %m
1090 EMG stop switch (software) is activated.
Head height cannot be changed when any nozzle is in
Detected EMG SW.
1091
the ANC.
Use only one nozzle.
1092 The tray direction is wrong. (Pallet-%d1)
An error occurred during Feeder Support Function. %s
Check the tray direction.
Check the pickup data, image data, and condition of
1093
: %d1 pickup point.
To restart the production, cancel the error and
1094 Conveyor width is changed.
Electrodes partly could not be recognized. %m
remove the PCB.
Component centering is performed only by the
1095
Head%c1
%c4 has been failed. (Head%c6%s Target %d1
recognizable electrodes.
Check for a dropped component beneath the head.
1096
Pushdown Stroke %d5 Feedback %d2 Tolerance %d3 Then resume production.
System is not functioning normally. Acquire the Log
1097 System failure is detected.
File and. contact us immediately.
1098 Drive phase error Contact us.
1099 Safety stop has been detected.
1100 System error Contact us.
1101 %s is open. Close the cover.
1102 Invalid program step number is specified. Correct Start Step and/or Repeat Offset Step.
1103 %s pallet stopper is open. Close the pallet stopper.
1104 Feeder setting error Check if the feeder's ready lamp (green) is on.
Error is found in the program or in libraries during a
1105 Data error is found in the program or in libraries.
job run. Contact us.
1106
1107
MX-20 pallet stopper is open.
Safety guard sensor responded.
Close the pallet stopper.
Remove the obstacle from the sensing area. If no
obstacle is present, clean the sensor and check the
sensor's wiring.
1108 Cancel process is interrupted. Recover the interrupted process by manual operation.
1109 Forcible immediate stop (debug mode)
1110 Servo motors are off. You can turn them on.
1111 Detected %s axis immediate stop signal. Remove the cause of the error (open cover, etc.).
1112 Executed immediate stop. Failed to execute cycle Current cycle is not complete.
1113 Timeout in completing the cycle stop Remove the cause of other provided errors.
1114 Cycle stop sequence error Remove the cause of other provided errors.
1115 Error in activating <Start> switch. Remove the cause of other provided errors.
Identify the cause of error and reset the machine
1116 Error in activating <Cancel> switch.
state using the Manual menus.
This error is caused by effect of other errors. Check
1117 Axes motion error
Dual axis following-up error (Y1axis %d1 Y2axis %d2
the other error messages near around.
Dual axis following-up error occurred. Check the
1118
Tolerance %d3)
%c6%s positioning timeout (Target %d1 Feedback %d2
movement of Y axes.
Timeout for completion of positioning occurred.
1119
Tolerance %d3) Check the system parameters for encoder input for
Software limit over is detected. Check the parameter
1120 %c5%c6%s Software limit over (Target%d1 Limit%d2)
setting.
1121
Interlock error occurred between Z-axis1 and Scan-
axis (scan:%d1 %d2->%d3).
S-axis error. Check the machine state and contact
us.
1122
Interlock error occurred between Z-axis2 and Scan-
axis (scan:%d1 %d2->%d3).
S-axis error. Check the machine state and contact
us.
1123
Interlock error occurred between Z-axis3 and Scan-
axis (scan:%d1 %d2->%d3).
S-axis error. Check the machine state and contact
us.
1124
Interlock error occurred between Z-axis4 and Scan-
axis (scan:%d1 %d2->%d3).
S-axis error. Check the machine state and contact
us.
1125
Interlock error occurred between Z-axis5 and Scan-
axis (scan:%d1 %d2->%d3).
S-axis error. Check the machine state and contact
us.
1126
Interlock error occurred between Z-axis6 and Scan-
axis (scan:%d1 %d2->%d3).
S-axis error. Check the machine state and contact
us.