M20_Ope_E - 第447页
1248 Halt of message output: %d1times. System time: %d2. Halted time: %d3 seconds. Message buffer is full, and message is paused. 1174 Shuttle of MX40 contacts with conveyor rail. Check conveyor rail position against boa…
1172 Cannot create order to feed components. System error. Contact us immediately.
1173 MX-40 operation error Check MX-40 setting and conditions of MX-40B.
1128
Interlock error occurred between Z-axis of Head%c6
and Scan-axis (scan:%d1 %d2->%d3).
S-axis error. Check the machine state and contact
us.
1129
Origin discrepancy between y dual axes %d1 < (%d2-
%d3)
Origin sensor for Y2 axis may be troubled.
1130
Nozzle presence check upon ANC cannot be
Process is not properly performed. Contact us.
performed.
1131 Nozzle presence check on head cannot be performed. Process is not properly performed. Contact us.
1132 Image capture of fiducial mark cannot be performed. Process is not properly performed. Contact us.
1133
1134
Image capture of bad mark cannot be performed.
Image capture of component cannot be performed.
Process is not properly performed. Contact us.
Process is not properly performed. Contact us.
1135
Nozzle specified in placement program is not
identified in nozzle ID recognition.
Check program and nozzle information.
1136
Error is found in program in recognition process for
Check placement program.
nozzle on head.
1137
1138
Error program data is found in fiducial mark process.
Error program data is found in bad mark process.
Check Fiducial in placement program.
Check Bad mark in placement program.
1139
Error program data is found in vision-processing
component.
Check component name in placement program and
component data.
1140
Failed to identify fiducial mark. %m %c4%c5 step
No.%d2 for repeat offset step No.%d3
Check the fiducial mark data.
1141
Failed to identify bad mark. %m %c4%c5 step No.%d2
Check the bad mark data.
for repeat offset step No.%d3
1142
1143
Cannot perform bring back detection.
Cannot capture an image in bring back detection.
Cannot perform Component remain check.
Cannot capture an image in Component remain check.
1144
Open %s was detected during axis movement in the
MANUAL mode.
Close the cover.
1145
The system switched to the MANUAL mode in the job
Place the system in the AUTO mode.
run.
1146
1147
Job run cannot be performed in the MANUAL mode.
%s is not set up.
Place the system in the AUTO mode.
Set up the CFB.
1148 No nozzle is set on the head. %s
No nozzle is set on the head which is specified for
fixed nozzle in the user parameter..
1149 Nozzle is set on the head. %s
Auto nozzle change in scanning nozzles is prohibited.
1150 Nozzle Information includes errors. %s
Manually return the nozzle(s) to ANC.
Redo ANC scanning.
1151
Nozzles in heads and Nozzle Information contradict. Check nozzle setting. Contact us for ANC scanning
%s error.
1152 ANC slide channel operation timeout. %s Actuate ANC slide channel in Manual>Actuator.
1153 Required nozzle isn't found in ANC. %s Set required nozzle in ANC.
1154
1155
No available nozzle station. %s
No PCB fed from pre-process machine (SMEMA).
Check ANC.
Check interface setting of pre-process conveyor.
1156
Entrance sensor gets ON without input of machine-
not-ready signal (SMEMA).
Check interface setting of pre-process conveyor.
1157
Axis status mismatch.(X:%d1 %d2->%d3 Y:%d4 %d5- Obtain log data by clicking the <LOG> button and
1158
>%d6 [%d8])
Fluid shortage on Head%c1.
contact us.
1159
Board jams between exit of pre-process and arrival
sensor.
Check conveyor belts and conveyor motors.
1160
Board jams between exit of pre-process and buffer
Check conveyor belts and conveyor motors.
1161
sensor.
Board jams between buffer sensor and arrival sensor. Check conveyor belts and conveyor motors.
1162
Board jams between arrival sensor and entrance of
post-process.
Check conveyor belts and conveyor motors.
1163 Main clamp error
Check support pins and adjust plate for foreign
obstacles.
1164
1165
Side clamp error
Rear clamp error
Check side clamp for foreign matter.
Check rear clamp for its set position.
1166 Board stopper error
Actuate board stopper in manual menu
(Actuator/LoadBoard).
1167 Conveyor error
Check conveyor belts and associated
sensors/cylinders.
1168 Machine-not-ready signal does not turn OFF. Check interface setting of pre-process conveyor.
1169
1170
Machine-not-ready signal does not turn OFF.
The syringe is not set on Head%c1.
Check interface setting of post-process conveyor.
Check the syringe for the head.
1171 Fluid shortage warning sensor error on Head%c1.
Check the fluid shortage warning sensor and the
syringe.
1248
Halt of message output: %d1times. System time: %d2.
Halted time: %d3 seconds.
Message buffer is full, and message is paused.
1174 Shuttle of MX40 contacts with conveyor rail.
Check conveyor rail position against board Y at Board
1175 MX-20 operation error (Pallet-%d1)
menu.
Check MX-20 setting and conditions of MX-20F.
1176 MX-20's shuttle interferes with conveyor rail.
Compare conveyor rail position with
BoardData>BoardSize(Y).
1177 PCB is on the conveyor. Cannot adjust conveyor Remove the PCB from the conveyor.
1178
1179
Detected support pins under the conveyor rail.
LIM unit error.
Reject conveyor %s %d1 is full. Remove components
Remove the support pins under the conveyor rail.
Check the component ID. Check the LIM unit.
Remove components from Reject Conveyor and keep
1180
and press RESET switch. Then press START switch.
pressing TRANSFER/RESET switch for 3 seconds.
Then press START switch.
1181
Interlock against interference between Z-axis1 and %s
worked (Travel height:%d1 X:%d2 Y:%d3).
Error at the head actuators/motors. Check the head
coordinates and contact us.
1182
Interlock against interference between Z-axis2 and %s
worked (Travel height:%d1 X:%d2 Y:%d3).
Error at the head actuators/motors. Check the head
coordinates and contact us.
1183
Interlock against interference between Z-axis3 and %s
worked (Travel height:%d1 X:%d2 Y:%d3).
Error at the head actuators/motors. Check the head
coordinates and contact us.
1184
Interlock against interference between Z-axis4 and %s
worked (Travel height:%d1 X:%d2 Y:%d3).
Error at the head actuators/motors. Check the head
coordinates and contact us.
1185
Interlock against interference between Z-axis5 and %s
worked (Travel height:%d1 X:%d2 Y:%d3).
Error at the head actuators/motors. Check the head
coordinates and contact us.
1186
Interlock against interference between Z-axis6 and %s
worked (Travel height:%d1 X:%d2 Y:%d3).
Error at the head actuators/motors. Check the head
coordinates and contact us.
1187
Head%c6 interlock worked while CX axis is moving
(head height: %d1 < %d2).
Error at the head actuators/motors. Check the head
coordinates and contact us.
1188
Interlock against interference between Head%c6 Z-
axis and %s worked (Travel height:%d1 < %d4 X:%d2
Error at the head actuators/motors. Check the head
coordinates and contact us.
1189
The sensor detected the temperature error on
Head%c1.
Check Temperature Controller and Cable connection.
1190
Error is detected in recovery process. Production is
aborted.
Program's internal factor. Gather log data and contact
us.
1191
Head1 interlock worked while S axis is moving (head
height: %d1 < %d2).
Error at head actuators/motors. Check the head
height and contact us.
1192
Head2 interlock worked while S axis is moving (head
height: %d1 < %d2).
Error at head actuators/motors. Check the head
height and contact us.
1193
Head3 interlock worked while S axis is moving (head
height: %d1 < %d2).
Error at head actuators/motors. Check the head
height and contact us.
1194
Head4 interlock worked while S axis is moving (head
height: %d1 < %d2).
Error at head actuators/motors. Check the head
height and contact us.
1195
Head5 interlock worked while S axis is moving (head
height: %d1 < %d2).
Error at head actuators/motors. Check the head
height and contact us.
1196
Head6 interlock worked while S axis is moving (head Error at head actuators/motors. Check the head
1197
height: %d1 < %d2).
%c1 switch cannot be activated because %s is ON.
height and contact us.
Please release the Emergency stop button.
1198
Head%c6 interlock worked while S axis is moving
(head height: %d1 < %d2).
Error at head actuators/motors. Check the head
height and contact us.
1199
1200
Message issue error. Message buffer is cleared.(
Trouble:%d1 Ready:%d2 Get:%d3 Clear:%d4 )
Stopped to issue messages temporarily, resulting in
missing messages.
Production stopped immediately. Pickup motion was
attempted at out of the tolerance point. Head:%c1,
Placement command coord (X:%d2,Y:%d3)[micrometer],
1201
Placement feedback coord (X:%d4,Y:%d5)[micrometer],
Tolerance+/-%d6[micrometer]
Production stopped immediately. Placement motion
was attempted at out of the tolerance point.
Head:%c1, Placement command coord
1202
(X:%d2,Y:%d3)[micrometer], Placement feedback coord
(X:%d4,Y:%d5)[micrometer], Tolerance+/-
Placement motion was attempted at coordinates
already placed. It will cause double placement. Cancel
the production. (Head:%c1, Placement row:%d2, Repeat
offset row:%d3)
1203
Double placement check is not performed because
placement steps or repeat offsets exceed the limit.
Double placement check works for maximum of 2000
placement steps and maximum of 200 repeat offsets.
1204
Cannot continue production because of an error.
1205
Cancel the job.
Cannot load a PCB during machine pause
1291 MX-20 Cover Open (Pallet-%d1) 0
1292 MX-20 Pallet Interlock in Stocker (Pallet-%d1) Check conditions of MX-20.
1249 Clearing of message buffer.
Message buffer is cleared because message was
paused for prescribed time.
1250
1251
MX-20 Pallet Exists on Shuttle (Pallet-%d1)
MX-20 No Pallet on Shuttle (Pallet-%d1)
Check MX-20 setting.
Check MX-20 setting.
1252
MX-20 Pallet Exists on Shuttle whereas Pallet Not
Programmed (Pallet-%d1)
Check MX-20 setting.
1253
MX-20 No Pallet on Shuttle whereas Pallet
Check MX-20 setting.
Programmed (Pallet-%d1)
1254
1255
MX-20 Pallet Exists in Stocker (Pallet-%d1)
MX-20 No Pallet in Stocker (Pallet-%d1)
Check MX-20 setting.
Check MX-20 setting.
1256
MX-20 Pallet Exists in Stocker whereas Pallet Not
Programmed (Pallet-%d1)
Check MX-20 setting.
1257
MX-20 No Pallet in Stocker whereas Pallet
Check MX-20 setting.
1258
Programmed (Pallet-%d1)
MX-20 Pallet No. Failure in Stocker (Pallet-%d1) Check MX-20 setting.
1259
MX-20 Timeout in Locking Pallet Stopper in Stocker
(Pallet-%d1)
Check conditions of MX-20.
1260
MX-20 Timeout in Unlocking Pallet Stopper in
Check conditions of MX-20.
Stocker (Pallet-%d1)
1261 MX-20 Timeout in Relay Hook Up (Pallet-%d1) Check conditions of MX-20.
1262 MX-20 Timeout in Relay Hook Down (Pallet-%d1) Check conditions of MX-20.
1263 MX-20 Timeout in Shuttle Clamp (Pallet-%d1) Check conditions of MX-20.
1264 MX-20 Timeout in Shuttle Unclamp (Pallet-%d1) Check conditions of MX-20.
1265 MX-20 Timeout in Elevator Movement (Pallet-%d1) Check conditions of MX-20.
1266
1267
MX-20 Timeout in Shuttle Movement (Pallet-%d1)
MX-20 Timeout in Relay Hook Movement (Pallet-
Check conditions of MX-20.
Check conditions of MX-20.
1268
MX-20 Timeout for Elevator Returning to Origin
(Pallet-%d1)
Check conditions of MX-20.
1269
MX-20 Timeout for Shuttle Returning to Origin
(Pallet-%d1)
Check conditions of MX-20.
1270
MX-20 Timeout for Relay Hook Returning to Origin
Check conditions of MX-20.
(Pallet-%d1)
1271 MX-20 Stocker Interlock (Pallet-%d1) Check conditions of MX-20.
1272
1273
MX-20 Relay Hook Origin Sensor On (Pallet-%d1)
MX-20 Relay Hook Origin Sensor Off (Pallet-%d1)
Check conditions of MX-20.
Check conditions of MX-20.
1274
MX-20 Relay Hook Advance End Sensor On (Pallet-
%d1)
Check conditions of MX-20.
1275
MX-20 Relay Hook Advance End Sensor Off (Pallet-
Check conditions of MX-20.
%d1)
1276
1277
MX-20 Relay Hook Down Sensor On (Pallet-%d1)
MX-20 Relay Hook Down Sensor Off (Pallet-%d1)
Check conditions of MX-20.
Check conditions of MX-20.
1278
MX-20 Pallet Clamp Off Sensor on Shuttle On
(Pallet-%d1)
Check conditions of MX-20.
1279
MX-20 Pallet Clamp Off Sensor on Shuttle Off
(Pallet-%d1)
Check conditions of MX-20.
1280
MX-20 Pallet Stopper Off Sensor in Stocker On
(Pallet-%d1)
Check conditions of MX-20.
1281
MX-20 Pallet Stopper Off Sensor in Stocker Off
(Pallet-%d1)
Check conditions of MX-20.
1282
MX-20 Failed in Assigning Elevator Moving Position
(Pallet-%d1)
Check conditions of MX-20.
1283
MX-20 Failed in Assigning Relay Hook Moving
Position (Pallet-%d1)
Check conditions of MX-20.
1284
MX-20 Failed in Assigning Shuttle Moving Position
(Pallet-%d1)
Check conditions of MX-20.
1285
MX-20 Shuttle/Conveyor-width Position Error
(Pallet-%d1)
Check conditions of MX-20.
1286
MX-20 Front Shuttle Position Sensor Not Respond
after Shuttle Movement (Pallet-%d1)
Check conditions of MX-20.
1287
MX-20 Rear Shuttle Position Sensor Not Respond
after Shuttle Movement (Pallet-%d1)
Check conditions of MX-20.
1288
MX-20 Shuttle Origin Sensor Not Respond after
Shuttle Movement (Pallet-%d1)
Check conditions of MX-20.
1289
MX-20 Relay Hook Origin Sensor Not Responds after
Relay Hook Movement (Pallet-%d1)
Check conditions of MX-20.
1290
MX-20 Relay Hook Advance End Sensor Not Respond
Check conditions of MX-20.
after Relay Hook Movement (Pallet-%d1)