M20_Ope_E - 第453页

1531 %s Hook unlock sensor ON. (Pallet-%d2) Check conditions of MXR 1532 %s Hook unlock sensor OFF. (Pallet-%d2) Check conditions of MXR 1533 %s Stocker area sensor detected a pallet. Check conditions o f MXR 1480 Measur…

offset. X:%d1 Y:%d2 Alarm:%d3 T:%d4 Alarm:%d8 range. Check the parameter setting.

1479

Dispense Nozzle Offset OK Head%c1 Angle:%d2 X:%d3

Y:%d4 T:%d5 The number of adjustments:%d8

1440 Unclamp MX-ST2.

Reached the limit of pickup or vision-process error

Unclamp MX-ST2.

1441 count. Feeder Skip %m %s-%d3 Head%c1 Nozzle:%d2

Step:%d5 Offset:%d6

Other feeder(s) will be used. The feeder will be

skipped from now on.

1442

Nozzle is detected on Head%c1. Does not agree with

inf. on Head-Nozzle Setup.

Nozzle change by hand is prohibited. Check if the tip

of the head is clean.

Nozzle is not detected on Head%c1. Does not agree

1443

1444

with inf. on Head-Nozzle Setup.

Nozzle change by hand is prohibited.

Specified number of PCBs have been produced. Press the Cancel switch to abort.

Failed to scan the PCB code. When a placed PCB is

1445

1446

unloaded, the mounter will pause by an error.

%m mode

The PCB code is scanned. When a placed PCB is

1447 unloaded, the program will be switched to the scanned

program.

Make settings of Dot Station Dispense Check in the

1448

1449

Dispense Check Data for Head%c1 is not found.

FL detect correction is disabled.

dispense check program.

FL detect correction is disabled in the user

1450

Both the FL detect correction and the vision

correction are enabled.

Select either FL detect correction or vision

correction.

Image processing result %m %s%c8 Head%c1 X:%d2

1451

Y:%d3 T:%d4 (%d5,%d6,%d7)

Component image is taken by camera.

1452 Setup of %s starts.

1453

1454

Setup of %s ends.

%s #%d1 component is set. (Components:%d2)

Updated the initial pickup point for %s [ #%d1 (P%d2#-

1455

%d3 pallet) ].

1456 %s CFB is locked.

1457 %s CFB is released.

1458

1459

%s pallet is returned.

The system switched to the %s mode.

1460

AMF Fiducial. Code:%d1 Group:%d2 X;%d3 Y:%d4 T:%d5

( %d6 %d7) %m

AMF Placement Head%d1 Angle:%d2 X:%d3 Y:%d4 T:%d5

1461

1462

(%d6 %d7 %d8) %m

Halt of head movement during PCB arrival wait %s

1463

Resumption of head movement on completion of PCB

arrival. PCB arrival wait time: %d1.%d4 seconds %s

1464

Area detection event error.(%d1 %d2:%d5 %d3->%d4

[%d8])

Obtain log data by clicking the <LOG> button and

1465

Axis status mismatch.(X:%d1 %d2->%d3 Y:%d4 %d5-

>%d6 [%d8])

Obtain log data by clicking the <LOG> button and

1466 The sensor detected the fluid shortage on Head%c1. Replenish the head with fluid in good time.

1467 Area interlock has been detected.

Obtain log data by clicking the <LOG> button and

1468

1469

1470

Switched to MX-40 upper stocker.

Switched to MX-40 lower stocker.

Timeout in temperature control for Head%c1 Check the temperature controller.

1471

Dispensing was started without the set temperature

being reached for Head%c1. Target:%v2deg C Check the temperature controller.

1472

Current:%v3deg C

Halt of Head%c1 movement for awaiting completion of

temperature control

1473

Short of OK counts for Head%s. OK count:%p2

Average ratio:%d3% Tolerance:%d4%-%d5%

Pressure:%v6Mpa Correction coefficient:%v1 %m

Number of retrials exceeded the Max Check Count

OK count < Min OK Count. Check the nozzle, syringe,

parameters.

1474

for Head%s. OK count:%p2 Average ratio:%d3% Number of retrials exceeded the specified Max Check

Tolerance:%d4%-%d5% Pressure:%v6Mpa Correction

coefficient:%v1 %m

Count. Check the nozzle, syringe, parameters.

1475

1476

Retry/Skip is not specified. Specify whether to retry or skip.

Measure DP %s( F:%d1 X:%d2 Y:%d3 AR:%d4 LS:%d5

1477

SS:%d6 SD:%d7 T:%d8 %m )

Dispense Nozzle Offset Adjustment Head%c1

1478

Angle:%d2 X:%d3->%d4 Y:%d5->%d6 T:%d7->%d8

Error in automatic acquisition of dispense nozzle Coordinates correction values exceeded the allowable

1531 %s Hook unlock sensor ON. (Pallet-%d2) Check conditions of MXR

1532 %s Hook unlock sensor OFF. (Pallet-%d2) Check conditions of MXR

1533 %s Stocker area sensor detected a pallet. Check conditions of MXR

1480

Measure DP %s( F:%d1 X:%d2 Y:%d3 AR:%d4 LS:%d5

1481

SS:%d6 SD:%d7 T:%d8 %m )

The component %m" in step No.%d1 for repeat offset

Remain Check:%d4)"

1482

step No.%d2 will be skipped. (Head%c3

The component %m" will be skipped from the step

No.%d1 for repeat offset step No.%d2. (Head%c3)"

The component exhaustion process for %m" will be

1483 postponed from the step No.%d1 for repeat offset

step No.%d2."

1484 Paused for component exhaustion. Replenish the feeder with components to restart.

1485

Production was started with the Postpone

Component Exhaustion Process" function disabled."

To enable the Postpone Component Exhaustion

Process" function

1486

1487

Out of components (%m).

The component %m" in step No.%d1 for repeat offset

Refill the components.

1488

step No.%d2 will be postponed."

Buffer stopper error

Actuate buffer stopper in manual menu

1489

Changed to safety stop" state because %s was

(Actuator/LoadBoard).

To resume production run, close the cover and press

opened." the Servo switch.

1490

Switched to %s mode and changed to safety stop"

state."

To resume production run, close the cover and press

the Servo switch.

1491

1492

Switched to %s mode.

Switched to %s mode and changed to safety stop" To resume production run, close the cover and press

state." the Servo switch.

1493

Coordinates have been lost due to trouble in return-

to-coordinate process.

Take origin again.

1494 %c1 switch cannot be activated because %s is open. Close the cover.

1495

Job run cannot be performed because the machine is

Press the Servo switch.

in the safety stop" state."

1497

1500

%s Pallet exists on hook. (Pallet-%d2)

Message

Check MXR setting

1501

1502

%s No pallet on hook. (Pallet-%d2)

%s Pallet exists on hook whereas pallet not

Check MXR setting

programmed. (Pallet-%d2)

1503

%s No pallet on hook whereas pallet programmed.

Check MXR setting

1504

(Pallet-%d2)

%s Pallet exists in stocker. Check MXR setting

1505

1506

%s No pallet in stocker. (Pallet-%d2)

%s Pallet exists in stocker whereas pallet not

Check MXR setting

programmed. (Pallet-%d2)

1507

%s No pallet in stocker whereas pallet programmed.

Check MXR setting

(Pallet-%d2)

1508 %s Pallet No. Failure in Stocker. (Pallet-%d2) Check MXR setting

1509 %s Timeout for door lock. (Pallet-%d2) Check conditions of MXR

1510 %s Timeout for door unlock. (Pallet-%d2) Check conditions of MXR

1511 %s Timeout for hook lock. (Pallet-%d2) Check conditions of MXR

1512 %s Timeout for hook unlock. (Pallet-%d2) Check conditions of MXR

1513 %s Timeout for pallet bar open. (Pallet-%d2) Check conditions of MXR

1514 %s Timeout for pallet bar close. (Pallet-%d2) Check conditions of MXR

1515 %s Timeout for pallet side clamp ON. (Pallet-%d2) Check conditions of MXR

1516 %s Timeout for pallet side clamp OFF. (Pallet-%d2) Check conditions of MXR

1517 %s Timeout for pallet rear clamp ON. (Pallet-%d2) Check conditions of MXR

1518

1519

%s Timeout for pallet rear clamp OFF. (Pallet-%d2)

%s Timeout in Elevator Movement. (Pallet-%d2)

Check conditions of MXR

1520 %s Timeout in Hook Movement. (Pallet-%d2) Check conditions of MXR

1521

%s Timeout for Elevator Returning to Origin. (Pallet-

Check conditions of MXR

%d2)

1522 %s Timeout for Hook Returning to Origin. (Pallet-%d2) Check conditions of MXR

1523 %s Pallet advance end sensor ON. (Pallet-%d2) Check conditions of MXR

1524 %s Pallet advance end sensor OFF. (Pallet-%d2) Check conditions of MXR

1525 %s Pallet bar open sensor ON (Pallet-%d2) Check conditions of MXR

1526 %s Pallet bar open sensor OFF (Pallet-%d2) Check conditions of MXR

1527 %s Pallet bar close sensor ON (Pallet-%d2) Check conditions of MXR

1528 %s Pallet bar close sensor OFF (Pallet-%d2) Check conditions of MXR

1529 %s Hook lock sensor ON. (Pallet-%d2) Check conditions of MXR

1530 %s Hook lock sensor OFF. (Pallet-%d2) Check conditions of MXR

%d1 return MX-20 to origin.

1572

MX-20 Pallet detect sensor in Stocker is OFF.

Pallet-%d1

Insert the specified Pallet into MX-20 stocker.

1534 %s Pallet detect sensor on hook ON. (Pallet-%d2) Check conditions of MXR

1535 %s Pallet detect sensor on hook OFF. (Pallet-%d2) Check conditions of MXR

1536 %s Pallet side clamp sensor ON. (Pallet-%d2) Check conditions of MXR

1537 %s Pallet side clamp sensor OFF. (Pallet-%d2) Check conditions of MXR

1538 %s Pallet rear clamp sensor ON. (Pallet-%d2) Check conditions of MXR

1539

1540

%s Pallet rear clamp sensor OFF. (Pallet-%d2)

%s Hook-axis is out of origin position. (Pallet-%d2)

Check conditions of MXR

1541

1542

%s Hook-axis is out of supply position. (Pallet-%d2)

%s Failed in Assigning Elevator Moving Position

Check conditions of MXR

(Pallet-%d2)

1543

%s Failed in Assigning Hook Moving Position (Pallet-

Check conditions of MXR

1544

1545

%d2)

%s Door Open (Pallet-%d2)

%s Elevator Slow-down Stop (Pallet-%d2)

Check conditions of MXR

1546

%s Pallet Interlock. Remove the pallet in the middle of

being supplied and check in the Manual menu. Then Check conditions of MXR

1547

perform axis zeroing.

The relay hook of MX20 is not in Stocker Position for

Secure the safety of MX20 unit and take origin.

Relay" position."

1548

No PCB has been selected in the PCB select bad

mark" process."

Check the board for bad marks.

1549 Nozzle No.[%d2] is not found in nozzle library. Check nozzle library.

1550 Cannot perform dispense check.

Check the image library and the image code in the

1551 Cannot capture an image in dispense check.

dispense library.

Process is not properly performed. Contact us.

1552

1553

Syringe change signal for Head%c1 has been

The nozzle set in the dedicated ANC is different from

Acception parameter for syringe has been initialized.

Check nozzle setting.

1554

specified one. ANC(%d1)

Nozzle is set on the Head%c1.

Check ANC shutter and missetting of nozzle. Contact

us for ANC scanning error.

1555

1556

Communication fails.

System status is changed.

Cancel command cannot be sent to the vision

system. Contact us.

System diagnoses itself.

1557

Head%s Dispense Correction OK count:%p2 Average

ratio:%d3% Tolerance:%d4%-%d5% Correction

Value:%v8Mpa Pressure:%v6Mpa Retry Count:%d7 %m

Executing Dispense Correction

1558

Head%s Dispense Check OK OK count:%p2 Average

ratio:%d3% Tolerance:%d4%-%d5% Pressure:%v6Mpa

Correction coefficient:%v1 Retry Count:%d7 %m

Dispense Check Passed

1559

Short of nozzles for the current program. Nozzle:%d1

Number of Nozzles:%d2 Number of set nozzles:%d3

Number of shortage nozzles:%d4 %s

Set the required nozzles.

1560

Shortage of the optimum number of nozzles.

Nozzle:%d1 Optimum number:%d2 Set number:%d3

Set the proper number of nozzles for efficient

production.

1561

Short number:%d4 %s

Automatic nozzle arrangement will be skipped

Check the setting in User Parameter > Functions.

1562

according to the user parameter setting.

Auto nozzle arrangement cannot be performed

Release the Fixed Nozzle setting for head 1 and 2.

because head 1 and/or 2 are set for Fixed Nozzle"."

1563

Component %m" is not set on %s-%d1. Feeder ID

%d2-%d3"

Confirm the component on the feeder.

1564

1565

The program cannot be run since feeder is

Exceeded the maximum correction value. %s(X:%d1

Y:%d2 T:%d3) Head%c4 %m

Confirm the feeder location.

Click the <LOG> button to obtain Log data, and

1566

Remove the pallet-%d1 from the tray feeder. It must

be done while the Servo motor is off.

Turn off the Servo motor from the Maintenance

Menu. Remove the pallet, which was failed to be

1567

The nozzles required for the production are not set at

delivered, out of the tray feeder and return all the

Set the nozzle at proper position where the head can

1568

proper position of ANC. Head%c1 Nozzle:%d2

Z-axis did not reach the pickup height when pickup.

use.

Check the Head Z axis condition.

1569

Head%c1 Nozzle:%d2

Z-axis did not reach the placement height when

Check the Head Z axis condition.

1570

placement. Head%c1 Nozzle:%d2

Z-axis did not reach the Reject/Return height when

Check the Head Z axis condition.

1571

Reject/Return Component. Head%c1 Nozzle:%d2

MX-20 Pallet detect sensor in Stocker is ON. Pallet- Remove the specified Pallet from MX-20 stocker and