M20_Ope_E - 第461页

2020 the specific area with height restriction at Pin setup specification. 2021 A part of the mounted component may be out of PCB area specified by PCB size. 1984 The dispense code is not registered in the dispense Regis…

1981 Z coordinate for the mark is invalid. The specified coordinates is invalid.

1982 T coordinate for the mark is invalid. The specified coordinates is invalid.

1983

There are no steps or a End Block Placement step

after the bad mark step.

Check Placement&Mark data.

1941

[Pedestal Thickness] in the component data differs Set [Pedestal Thickness] in the component data to

from the user parameter. the user parameter setting.

1942

1943

0 is entered as [Component ID] (for coplanarity

[Pallet Retract] is After pickup" when [Reject/Reuse]

Set [Component ID] to 1-255.

The component is reused but the pallet is retracted

1944

is "Reuse"."

Nozzle name error.

after placement.

Use a nozzle name from the master library.

1945

The same code is used for image code and for fiducial

Change either the image code or the mark code.

1946

mark code.

The same code is used for image code and for bad

Change either the image code or the mark code.

1947

mark code.

The same code is used for both fiducial and bad mark. Change the mark code for either one.

1948

The nozzle set on the head is different from that

specified as a fixed nozzle.

Change either the nozzle on the head or designation

of the fixed nozzle.

1949

The nozzle No. specified is not registered in the

nozzle data.

Check the nozzle No. for the component.

1950 APC is valid only for F/R banks.

Disable the APC function for other parts than F/R

banks.

1951

1952

Delay for Vacuum ON" time is out of the range."

Grip Length" is out of the range."

Enter Delay for Vacuum ON" time in the nozzle data

in the range of 0 ms to 999 ms. "

Enter Grip Length" in the nozzle data in the range of

1.5 mm to 3.5 mm(59.1 mil to 137.8 mil)."

1953 The value for [Side Pickup Offset] is out of the range.

Enter a value for [Side Pickup Offset] in the nozzle

data in the range of 0.5 mm to 2.0 mm (19.69 mil to

78.74 mil) or -0.5 mm to -2.0 mm (-19.69 mil to -

1954

ST No. for reject conveyor in the packaging data is

78.74 mil).

Change the ST No. in the packaging data.

1955

out of the range.

There are 3 fiducial steps. Fiducial process must consist of 1, 2 or 4 fiducial

1956 Fiducial numbers are different.

Give the same fiducial number for each fiducial step

group.

1957

The distance between fiducial marks is less than The distance between fiducial marks is

3mm. 3mm(118.11mil) or more.

1958 Coordinates of the fiducial is not right. The interior angle must be less than 180 degrees.

1959 The value for xa coordinate is larger than that for xb. Make the value for xb coordinate larger than that for

1960 The value for xa coordinate is larger than that for xc. Make the value for xc coordinate larger than that for

1961 The value for xd coordinate is larger than that for xb. Make the value for xb coordinate larger than that for

1962 The value for xd coordinate is larger than that for xc. Make the value for xc coordinate larger than that for

1963

1964

The value for yc coordinate is larger than that for ya.

The value for yd coordinate is larger than that for ya.

Make the value for ya coordinate larger than that for

1965

1966

The value for yc coordinate is larger than that for yb.

The value for yd coordinate is larger than that for ya.

Make the value for yb coordinate larger than that for

Make the value for ya coordinate larger than that for

1967

Placement point is out of the valid range of 4-point Move the placement point in the valid range for 4-

fiducials. point fiducials.

1968 Assigned bad mark group is not defined.

Define the bad mark group No. for the program step

including bad mark group assignment.

1969

1970

Group Bad mark step is re-specified.

PCB bad mark is defined in the repeat steps.

Each group bad mark can be specified once.

Define the PCB bad mark outside the repeat steps.

1971 The value for bad mark group is incorrect.

Valid numbers for bad mark group are 254, 255, and 0

to 249.

1972 PCB bad mark is not defined in the first step.

Define the PCB bad mark in the first step when 254"

1973

The [Vision Inspection] is set to Not Apply" for the

component."

is specified for the bad mark group. "

Check the [Vision Inspection] in the component data.

1974

1975

Out of the valid range for compensation.

The value for Z offset for vision process" in the

component data is larger than 1mm or the component

Make it 2-point fiducial or change the mark position.

Make the value 1mm(39.37mil) or less or make it

smaller than the component thickness.

thickness."

The value for Thickness of component on nozzle" in

Make the value positive or smaller than the

1976 the component data is negative or larger than the

component thickness.

component thickness."

1977

The value for Grip Length" in the nozzle data is out Make the value in the range of 0mm to 5.5mm.(0mil to

of the range." 216.535mil.)

1978 Grip Length" is longer than the component Change the Grip Length"."

1979

1980

Task and Head do not match as the same function.

Head designation for dispensing is wrong.

Correct to match Task and Head as the same

Check the data type and head No.

2020 the specific area with height restriction at Pin setup

specification.

2021

A part of the mounted component may be out of PCB

area specified by PCB size.

1984

The dispense code is not registered in the dispense

data.

1985

1986

Coordinates for the dispense check step are invalid.

The offset value in the dispense data exceeds

The operation to specify coordinates here is invalid.

Correct the offset value in Dispense Data to be within

1987

DotStation area.

The image code in the dispense data is not registered.

DotStation area.

1988 Board size is not specified.

Data check for placement coordinates cannot be

performed properly.

1989 Distance for line dispense is not proper.

The value for the distance between the start and end

of discharge is negative.

1990 No line dispense option.

Line dispense cannot be assigned because the

optional line dispensing function is not included in this

1991 Line dispense designation is not proper.

There is no Start Line assignment before the End

Line assignment.

1992

1993

Feed style in the pallet data is not correct.

The syringe code is not registered in the syringe data.

Select the correct unit for the feed style.

1994 T coordinates for Repeat Offset steps will be invalid.

To make T coordinates for Repeat Offset steps valid,

perform block data conversion.

1995 The nozzle may interfere with placed components.

The problem may be solved if you place the thick

1996

This machine cannot use edge registration. It uses

component last.

Set Pin/Clamp for registration in Board data.

1997

clamp registration.

Thickness" is not specified in the Component Data." Input Thickness value in Component Data.

1998

The nozzle may interfere with pre-processed

components.

Check the Max Pre-processed Component Height in

Board Data.

1999

Repeat placement cannot be performed when PCB

Perform Block Data Conversion"."

2000

select bad mark" is used."

Optimization of nozzle arrangement was not Optimization of nozzle arrangement was not

2001

performed because of ANC shortage.

Reject tray No. is not specified in Reject Location No.

performed because of several factors.

Set 1" for Reject tray (F)

2002

Reuse" is selected although the feed style is "ST-F"

or "ST-R"."

Check that the setting of Reject/Reuse" is proper for

the target component code."

2003

Reject Location No. for reject conveyors must be 1 to

10.

Specify a number from 1 to 10 for Reject Location

No.

2004 Station No. for reject conveyor is not specified.

Specify the Station No. where Reject conveyor is set

in Pick data.

2005

2006

Reject Location No. for specified positions must be 3

to 10.

Reject Conveyor is selected although the feed style is

Specify a number from 3 to 10 for Reject Location

No. in Pick data.

Check that the setting of Reject/Reuse" is proper for

MX"." the target component code."

Y coordinate from ST origin should be in range of

2007 Y coordinate for reject tray is invalid. +56mm - +86mm for front, and -56mm - -86mm for

rear.

2008

Coordinates for reject location is either in ANC/Fixed

Camera area or in MX movable area.

Check the setting of Reject Location in User

Parameter whether the specified coordinates are

2009

The pickup point specified by Pickup Priority does not

exist.

Check the existence of the pickup point specified by

Pickup Priority.

2010

Pickup Area Travel Height + Offset value exceeds Set the Pickup Area Travel Height" to be below the

Normal Travel Height. "Normal Travel height". "

2011

This component code is registered in Pickup Data, but

Check the Placement&Mark data whether the skip

2012

it is skipped or not used in Placement & Mark Data.

setting is proper.

Reject Location No. in Tray Data exceeds range. Reject Location No. must be within 1 to 10.

2013

2014

X offset of pickup point is out of range. Check that the pickup coordinate is correct.

Y offset of pickup point is out of range. Check that the pickup coordinate is correct.

2015

The Repeat Offset data is not proper so that

placement points may be overlapped.

2016

Placement area of the component may be overlapped

with others.

2017

Flange part of nozzle may collapse with any of

mounted components on PCB.

Change the mounting order for the taller components

to be the last.

2018

2019

The mount point for the component is out of possible

placement area.

The mount point for the component is out of possible

placement area at Pin setup specification.

The component height exceeds the limit(2.0mm) in

2053 Too many fiducial processes.

(repeat steps included).

2054 The dispense point is out of the possible dispense

2055

The dispense point is out of the possible dispense

area at Pin setup specification.

2022

Prerotation function is not available because the

nozzle has restriction for rotation.

The nozzle is set to Fixed" or "Fixed(reversible)" for

Directionality

2023

The specified mark position is out of possible

recognition area.

2024

The specified mark position is out of possible

recognition area at Pin setup specification.

2025

2026

A part of the mark may be out of PCB area specified

by PCB size.

The component code name in the Placement data If there are any component codes containing any

2027

contains any space"key entries."

Component pickup surface height is set smaller than

Grip length.

space" key entries

Component pickup surface height should be set bigger

than Grip length. (Set 0 for the setting when pickup

Pre-rotation function cannot be performed when

height is same as component thickness.)

Take one of the following ways; specify Single

2028

2029

different mount angle is specified for each of

oriented-nozzles in the same cycle.

Pre-rotation cannot be performed for oriented-nozzle

Pickup" for Task

Take one of the following ways; specify Single

with other nozzles' rotation process in the same

The pre-rotation processed component may rotate

Pickup" for Task

To keep pre-rotated status, specify Single Pickup"

2030 after vision recognition because of other Heads'

rotating action in the same cycle.

for Task

2031

Feeder cannot set on the location because of

interference with next feeder.

Change ST No. to make more space with next feeder.

2032

The component size may be too small for the

specified camera to recognize.

Change Centering" setting to use another camera."

2033

The component size may be too larger for the

Change Centering" setting to use another camera

2034

specified camera to recognize.

The component height exceeds the limit for the

Change Centering" setting to use another camera."

2035

specified camera.

There is no model data for pattern matching. Acquire the model data.

2036

Some pickup records not used for the program have Be sure that this pickup record is not used during

2037

the same ST No. specified with others. production.

The components picked by both ends of head are too To avoid collision with scan camera, the multiple

large to perform multiple pickup in a same cycle. pickup will be divided in different pickup cycle.

2038

2039

Component is too large and may hit the scan camera. Select a fixed camera or change the head No.

The specified coordinates for dispensing are

2040

overlapping with others.

Coplanarity Check data is not registered. Please check Coplanarity Check data in Image data.

2041

2042

The number of Coplanarity check data to be used for

production is over the maximum, 99 records.

The Coplanarity check is not available even though it

Check the Coplanarity Check box in User Parameter.

is set to Use" in Component Data."

Spaces among the components that are captured

The same components that are measured at the same

2043

sequentially at Coplanarity Check are incorrect.

angle will be captured sequentially. Pick up the

components at the specified pitch intervals.

2044

Coplanarity check for this component cannot be

performed.

Choose Not Use" to disable "Coplanarity" fucntion

for this component."

2045

2046

The selected head unit is not equipped with

Coplanarity Checker.

The specified parameter for Transfer time after PCB

Select a correct head unit for Coplanarity Check.

It should be 101ms or more.

2047

passed the arrival sensor" is too much small."

The specified parameter for Delay for PCB Simul.

It should be bigger than the parameter of Transfer

time after PCB passed the arrival sensor" for 50ms

2048

Transfer" is too much small. "

When using the Relocatable function, it may be

impossible to start production if any pickup data are

or more."

Skip setting must be done in Placement data instead

set to NotAvailable"."

The component may collide with the other component

of pickup data.

2049 picked up by next head in a same pickup cycle

Divide the pickup cycle in different cycles or use

because of its large size.

other head to pick up in order to avoid the collision.

2050

Board Size has not been set yet, and data check for

mounting points cannot be performed.

Input Board Size correctly.

2051 There are any Placement steps skipped. Some components will not be placed. Check data

2052 There are any Pickup data skipped. Some components will not be placed. Check data

The number of fiducial processes must be 300 or less