M20_Ope_E - 第463页

2094 Entered value in Pallet Data>Speed is too slow. Enter 100(10%) or higher speed. 2095 Component outer size exceeds the capture limit of Head 1,4,5,8. Possible capture size of Head 1,4,5,8 is width 11mm or less. Ch…

2053 Too many fiducial processes.

(repeat steps included).

2054 The dispense point is out of the possible dispense

2055

The dispense point is out of the possible dispense

area at Pin setup specification.

2022

Prerotation function is not available because the

nozzle has restriction for rotation.

The nozzle is set to Fixed" or "Fixed(reversible)" for

Directionality

2023

The specified mark position is out of possible

recognition area.

2024

The specified mark position is out of possible

recognition area at Pin setup specification.

2025

2026

A part of the mark may be out of PCB area specified

by PCB size.

The component code name in the Placement data If there are any component codes containing any

2027

contains any space"key entries."

Component pickup surface height is set smaller than

Grip length.

space" key entries

Component pickup surface height should be set bigger

than Grip length. (Set 0 for the setting when pickup

Pre-rotation function cannot be performed when

height is same as component thickness.)

Take one of the following ways; specify Single

2028

2029

different mount angle is specified for each of

oriented-nozzles in the same cycle.

Pre-rotation cannot be performed for oriented-nozzle

Pickup" for Task

Take one of the following ways; specify Single

with other nozzles' rotation process in the same

The pre-rotation processed component may rotate

Pickup" for Task

To keep pre-rotated status, specify Single Pickup"

2030 after vision recognition because of other Heads'

rotating action in the same cycle.

for Task

2031

Feeder cannot set on the location because of

interference with next feeder.

Change ST No. to make more space with next feeder.

2032

The component size may be too small for the

specified camera to recognize.

Change Centering" setting to use another camera."

2033

The component size may be too larger for the

Change Centering" setting to use another camera

2034

specified camera to recognize.

The component height exceeds the limit for the

Change Centering" setting to use another camera."

2035

specified camera.

There is no model data for pattern matching. Acquire the model data.

2036

Some pickup records not used for the program have Be sure that this pickup record is not used during

2037

the same ST No. specified with others. production.

The components picked by both ends of head are too To avoid collision with scan camera, the multiple

large to perform multiple pickup in a same cycle. pickup will be divided in different pickup cycle.

2038

2039

Component is too large and may hit the scan camera. Select a fixed camera or change the head No.

The specified coordinates for dispensing are

2040

overlapping with others.

Coplanarity Check data is not registered. Please check Coplanarity Check data in Image data.

2041

2042

The number of Coplanarity check data to be used for

production is over the maximum, 99 records.

The Coplanarity check is not available even though it

Check the Coplanarity Check box in User Parameter.

is set to Use" in Component Data."

Spaces among the components that are captured

The same components that are measured at the same

2043

sequentially at Coplanarity Check are incorrect.

angle will be captured sequentially. Pick up the

components at the specified pitch intervals.

2044

Coplanarity check for this component cannot be

performed.

Choose Not Use" to disable "Coplanarity" fucntion

for this component."

2045

2046

The selected head unit is not equipped with

Coplanarity Checker.

The specified parameter for Transfer time after PCB

Select a correct head unit for Coplanarity Check.

It should be 101ms or more.

2047

passed the arrival sensor" is too much small."

The specified parameter for Delay for PCB Simul.

It should be bigger than the parameter of Transfer

time after PCB passed the arrival sensor" for 50ms

2048

Transfer" is too much small. "

When using the Relocatable function, it may be

impossible to start production if any pickup data are

or more."

Skip setting must be done in Placement data instead

set to NotAvailable"."

The component may collide with the other component

of pickup data.

2049 picked up by next head in a same pickup cycle

Divide the pickup cycle in different cycles or use

because of its large size.

other head to pick up in order to avoid the collision.

2050

Board Size has not been set yet, and data check for

mounting points cannot be performed.

Input Board Size correctly.

2051 There are any Placement steps skipped. Some components will not be placed. Check data

2052 There are any Pickup data skipped. Some components will not be placed. Check data

The number of fiducial processes must be 300 or less

2094 Entered value in Pallet Data>Speed is too slow. Enter 100(10%) or higher speed.

2095

Component outer size exceeds the capture limit of

Head 1,4,5,8.

Possible capture size of Head 1,4,5,8 is width 11mm

or less. Change the head No.

2096 Set position of the reject conveyor is not proper. Set the reject conveyor at a feeder placeable station.

2056

The Repeat Offset data is not proper so that

dispense points may be overlapped.

2057

The setting position of PS-MS3 exceeds allowable

range.

Do not set the PS-MS3 on the 2 feeder stations from

both ends of the feeder bank.

2058

Pre-rotation function is disabled because coplanarity

check function is specified.

The tip of the nozzle will move down lower than the Check Z of placement data, thickness and Z of board

2059

board surface when it mounts a component. origin of board data.

Specify the correct Head unit corresponding to the

2060

2061

Different Head unit is specified. Tray unit or specify the correct Tray unit

corresponding to the Head unit.

This unit cannot handle the inspection head. Specify the unit that has an inspection function.

2062 A different head unit is used for Multiple Pickup.

The components having unequal Illumination and

Specify Multiple Pickup with heads in a same unit.

2063 Gain/Offset values within one cycle will be Still-

captured.

2064 A shared Fiducial Mark step has not been created.

Uncheck the Share the Fiducial Mark Information"

check box

2065

Specified line as a shared Fiducial Mark step is not

correct.

Create the shared Fiducial Mark step at the top line

in Placement&Mark Data.

Component outer size exceeds the capture limit of Possible capture size of Head 1,4,5,8 is width 8mm or

2066

Head 1,4,5,8. less. Change the head No.

Input proper PCB length or decrease the number of

2067 PCB length is too long.

Placement stages.

2068 PCB length exceeds the limit.

Less than the possible number of placement stages is

2069

selected.

You can increase the number of Placement stages.

2070 It exceeds the placement range of Head unit B.

Head unit B cannot use Shared fiducial marks on the

Change a head or select Head unit A.

2071

2072

machine mounting two Placement stages.

Beam camera recognition cannot be used. Change Centering" setting to use another camera."

Pickup No. is not correct. (The feeder may not be

2073

attached in the position.)

The component may interfere with the next nozzle

Check no obstacles at both sides of the feeder.

Divide the pickup cycle in different cycles or use

2074

because its size is too large. other head to pick up in order to avoid the collision.

2075 Multiple-view process assignment is not proper. Select a proper multiple-view process.

Shared Fiducial/Bad mark is invalid when Mount

2076

2077

Stage Count is 1.

No image code for Image capture is found.

Uncheck the Shared Mark check box.

2078

2079

No image code for Image matching is found. Register an image code.

Placement steps exist prior to Image capture steps. Perform Image capture before starting placement.

2080

Placement other than BGA is found after Image

matching process.

Insert BGA placement steps right after Image

matching steps.

The number of Image capture and that of Image

2081

matching are not the same.

2082

The coordinates of Image capture and that of Image

matching do not match.

2083

2084

No fiducial mark process of this unit is found.

This Fiducial Group No. is not used.

Add fiducial mark steps.

2085

Board width (Y) of Board Data exceeds the limit

because of RTS-1.

2086

More than the number of heads is assigned in Pickup

Order.

Within the number of heads must be assigned in

Pickup Order.

Pickup Order is invalid because Pickup Priority is not

2087

specified.

2088

The same coordinate fiducial-mark is specified in

more than one fiducial groups.

2089

2090

Skip is selected for the priority Pickup Data. The Pickup Priority is invalid.

The priority Pickup Data is out of the travel range. The Pickup Priority is invalid.

2091

Component codes in Pickup Data and in Pickup

Priority do not match.

The Pickup Priority is invalid.

Pickup Order is invalid because improper Priority

2092

Pickup is specified.

The number of Image capture/matching steps must

2093 Too many Image capture/matching steps.

be within 999.

2130

warp check is too wide. same line zone.

2131

Number of points for the global PCB warp check is

not proper.

For the global PCB warp check, one group needs 3 to

50 points in the same line zone (Y) and 2 to 20 groups

are available.

2097

The component height entered in the Tray Data is too

Enter the height, from the tray bottom to the

component surface, for the component height in the

low.

Tray Data.

Enter the height, from the tray bottom to the

2098

The component height entered in the Tray Data is too

low.

component surface, for the component height in the

Tray Data.

2099

Mounting locations of the reject conveyor and the

feeder are overlapped.

2100

The coordinate X may exceed the head movable

range by the compensation of the placement point.

Change the head No.

2101

The set position of the reject conveyor exceeds

allowable range.

Change the set position of the reject conveyor.

2102

Component outer size exceeds the capture limit of

Head 1,3,4,6.

Possible capture size of Head 1,3,4,6 is width 25mm

or less. Change the head No.

2103

The components are too large to perform multiple

pickup in a same cycle.

The multiple pickup will be divided in different pickup

cycle.

Multiple pickup is specified for the component with Specify single pickup for the component with multi

2104

multi view process.

The image data used for the pattern matching cannot

view process.

Use image codes individually or specify the center

2105

2107

be used with a different camera

The used supply unit ID is not specified in the header.

Specify the supply unit ID.

2108

The supply unit ID specified in the header and the ID

of the used supply unit do not match.

Specify the ID of the used supply unit or exchange it

for the supply unit of the correct ID.

Specify global fiducial when Correct local fiducial

2109 Global fiducial is not specified.

marks" is selected."

Locate the local fiducial mark(s) in the range of the

2110

A local fiducial mark(s) locates out of the range of 4-

point-global-fiducial.

global fiducial when Correct local fiducial marks" is

selected."

2111

No Check" is selected for the ball check method in

the BGA/CSP image data."

2112

The front camera is used to capture the image of the

component picked up from the rear side.

To improve production efficiency, use the rear

camera.

2113

The rear camera is used to capture the image of the

component picked up from the front side.

To improve production efficiency, use the front

camera.

2114

A front head is used for the component picked up

from the rear side.

Use a rear head.

2115

A rear head is used for the component picked up from

the front side.

Use a front head.

2116 The coordinates of Flux Station exceed the range.

Correct the coordinates of Flux Station or select a

proper head.

2117

The coordinates of Flux Station locate either within

the work range of 'ANC/Fx-C Area', or 'MX' tray

Check the coordinates of Flux Station entered in the

user parameter.

2118

The coordinates of Flux Station locate within the

PCB area.

Check the coordinates of Flux Station.

2119

Flux process will not be executed because 'Disable' is

selected for Flux Station in the user parameter.

2120

Flux process is enabled to execute prior to vision

process, however Reuse" is selected in the program."

Change the process order or select other than

Reuse"."

Wait time on the surface of Flux Station exceeds 10

2121

sec.

Laser is specified in Head, but Laser Measurement is

2122

not selected in Algorithm.

2123

2124

The coordinates of reference corner exceed the

The setting position of MSF exceeds allowable range.

2125

2126

Reject tray cannot be used.

PCB warp check point is out of range.

Too many points exist in one group to check local Maximum 4 points are allowed in one group to check

2127

PCB warp. local PCB warp.

Create 3 to 50 points in the same line zone for the

2128

Number of points within the same line zone for the

global PCB warp check is not proper.

global PCB warp check. Points within 5% range of

PCB length (X) are accepted as the same line zone.

2129

Check range of the PCB in length (X) direction for the

global PCB warp check is too narrow.

Check points in the same line zone for the global PCB

Check range must be wider than 60% length (X) of the

PCB for the global PCB warp check.

Distance between points must be within 50mm in the