M20_Ope_E - 第464页

2130 warp check is too wide. same line zone. 2131 Number of points for the global PCB warp check is not proper. For the global PCB warp check, one group needs 3 to 50 points in the same line zone (Y) and 2 to 20 groups a…

2094 Entered value in Pallet Data>Speed is too slow. Enter 100(10%) or higher speed.

2095

Component outer size exceeds the capture limit of

Head 1,4,5,8.

Possible capture size of Head 1,4,5,8 is width 11mm

or less. Change the head No.

2096 Set position of the reject conveyor is not proper. Set the reject conveyor at a feeder placeable station.

2056

The Repeat Offset data is not proper so that

dispense points may be overlapped.

2057

The setting position of PS-MS3 exceeds allowable

range.

Do not set the PS-MS3 on the 2 feeder stations from

both ends of the feeder bank.

2058

Pre-rotation function is disabled because coplanarity

check function is specified.

The tip of the nozzle will move down lower than the Check Z of placement data, thickness and Z of board

2059

board surface when it mounts a component. origin of board data.

Specify the correct Head unit corresponding to the

2060

2061

Different Head unit is specified. Tray unit or specify the correct Tray unit

corresponding to the Head unit.

This unit cannot handle the inspection head. Specify the unit that has an inspection function.

2062 A different head unit is used for Multiple Pickup.

The components having unequal Illumination and

Specify Multiple Pickup with heads in a same unit.

2063 Gain/Offset values within one cycle will be Still-

captured.

2064 A shared Fiducial Mark step has not been created.

Uncheck the Share the Fiducial Mark Information"

check box

2065

Specified line as a shared Fiducial Mark step is not

correct.

Create the shared Fiducial Mark step at the top line

in Placement&Mark Data.

Component outer size exceeds the capture limit of Possible capture size of Head 1,4,5,8 is width 8mm or

2066

Head 1,4,5,8. less. Change the head No.

Input proper PCB length or decrease the number of

2067 PCB length is too long.

Placement stages.

2068 PCB length exceeds the limit.

Less than the possible number of placement stages is

2069

selected.

You can increase the number of Placement stages.

2070 It exceeds the placement range of Head unit B.

Head unit B cannot use Shared fiducial marks on the

Change a head or select Head unit A.

2071

2072

machine mounting two Placement stages.

Beam camera recognition cannot be used. Change Centering" setting to use another camera."

Pickup No. is not correct. (The feeder may not be

2073

attached in the position.)

The component may interfere with the next nozzle

Check no obstacles at both sides of the feeder.

Divide the pickup cycle in different cycles or use

2074

because its size is too large. other head to pick up in order to avoid the collision.

2075 Multiple-view process assignment is not proper. Select a proper multiple-view process.

Shared Fiducial/Bad mark is invalid when Mount

2076

2077

Stage Count is 1.

No image code for Image capture is found.

Uncheck the Shared Mark check box.

2078

2079

No image code for Image matching is found. Register an image code.

Placement steps exist prior to Image capture steps. Perform Image capture before starting placement.

2080

Placement other than BGA is found after Image

matching process.

Insert BGA placement steps right after Image

matching steps.

The number of Image capture and that of Image

2081

matching are not the same.

2082

The coordinates of Image capture and that of Image

matching do not match.

2083

2084

No fiducial mark process of this unit is found.

This Fiducial Group No. is not used.

Add fiducial mark steps.

2085

Board width (Y) of Board Data exceeds the limit

because of RTS-1.

2086

More than the number of heads is assigned in Pickup

Order.

Within the number of heads must be assigned in

Pickup Order.

Pickup Order is invalid because Pickup Priority is not

2087

specified.

2088

The same coordinate fiducial-mark is specified in

more than one fiducial groups.

2089

2090

Skip is selected for the priority Pickup Data. The Pickup Priority is invalid.

The priority Pickup Data is out of the travel range. The Pickup Priority is invalid.

2091

Component codes in Pickup Data and in Pickup

Priority do not match.

The Pickup Priority is invalid.

Pickup Order is invalid because improper Priority

2092

Pickup is specified.

The number of Image capture/matching steps must

2093 Too many Image capture/matching steps.

be within 999.

2130

warp check is too wide. same line zone.

2131

Number of points for the global PCB warp check is

not proper.

For the global PCB warp check, one group needs 3 to

50 points in the same line zone (Y) and 2 to 20 groups

are available.

2097

The component height entered in the Tray Data is too

Enter the height, from the tray bottom to the

component surface, for the component height in the

low.

Tray Data.

Enter the height, from the tray bottom to the

2098

The component height entered in the Tray Data is too

low.

component surface, for the component height in the

Tray Data.

2099

Mounting locations of the reject conveyor and the

feeder are overlapped.

2100

The coordinate X may exceed the head movable

range by the compensation of the placement point.

Change the head No.

2101

The set position of the reject conveyor exceeds

allowable range.

Change the set position of the reject conveyor.

2102

Component outer size exceeds the capture limit of

Head 1,3,4,6.

Possible capture size of Head 1,3,4,6 is width 25mm

or less. Change the head No.

2103

The components are too large to perform multiple

pickup in a same cycle.

The multiple pickup will be divided in different pickup

cycle.

Multiple pickup is specified for the component with Specify single pickup for the component with multi

2104

multi view process.

The image data used for the pattern matching cannot

view process.

Use image codes individually or specify the center

2105

2107

be used with a different camera

The used supply unit ID is not specified in the header.

Specify the supply unit ID.

2108

The supply unit ID specified in the header and the ID

of the used supply unit do not match.

Specify the ID of the used supply unit or exchange it

for the supply unit of the correct ID.

Specify global fiducial when Correct local fiducial

2109 Global fiducial is not specified.

marks" is selected."

Locate the local fiducial mark(s) in the range of the

2110

A local fiducial mark(s) locates out of the range of 4-

point-global-fiducial.

global fiducial when Correct local fiducial marks" is

selected."

2111

No Check" is selected for the ball check method in

the BGA/CSP image data."

2112

The front camera is used to capture the image of the

component picked up from the rear side.

To improve production efficiency, use the rear

camera.

2113

The rear camera is used to capture the image of the

component picked up from the front side.

To improve production efficiency, use the front

camera.

2114

A front head is used for the component picked up

from the rear side.

Use a rear head.

2115

A rear head is used for the component picked up from

the front side.

Use a front head.

2116 The coordinates of Flux Station exceed the range.

Correct the coordinates of Flux Station or select a

proper head.

2117

The coordinates of Flux Station locate either within

the work range of 'ANC/Fx-C Area', or 'MX' tray

Check the coordinates of Flux Station entered in the

user parameter.

2118

The coordinates of Flux Station locate within the

PCB area.

Check the coordinates of Flux Station.

2119

Flux process will not be executed because 'Disable' is

selected for Flux Station in the user parameter.

2120

Flux process is enabled to execute prior to vision

process, however Reuse" is selected in the program."

Change the process order or select other than

Reuse"."

Wait time on the surface of Flux Station exceeds 10

2121

sec.

Laser is specified in Head, but Laser Measurement is

2122

not selected in Algorithm.

2123

2124

The coordinates of reference corner exceed the

The setting position of MSF exceeds allowable range.

2125

2126

Reject tray cannot be used.

PCB warp check point is out of range.

Too many points exist in one group to check local Maximum 4 points are allowed in one group to check

2127

PCB warp. local PCB warp.

Create 3 to 50 points in the same line zone for the

2128

Number of points within the same line zone for the

global PCB warp check is not proper.

global PCB warp check. Points within 5% range of

PCB length (X) are accepted as the same line zone.

2129

Check range of the PCB in length (X) direction for the

global PCB warp check is too narrow.

Check points in the same line zone for the global PCB

Check range must be wider than 60% length (X) of the

PCB for the global PCB warp check.

Distance between points must be within 50mm in the

2171

Types of Priority nozzle and Substitute nozzle are

different.

Selection of Special Nozzle data of Priority nozzle

and Substitute nozzle must be the same.

2172 Coordinates of DotStation row cannot be changed. Keep coordinates of DotStaion 0.

2173 Components used in the program are not mounted.

2132

Check points in the same line zone for the global PCB

warp check is too close.

Distance between points must be wider than 5mm in

the same line zone.

Placement row exists prior to global PCB warp check

2133

rows.

Group No. of PCB warp check is specified prior to To use the same PCB warp check group, create PCB

2134

PCB warp check rows. warp check rows prior to placement rows.

2135 Group No. of PCB warp check is wrong. Available group Nos. of PCB warp check are 0-10000.

Data other than 0 is entered in Z coordiante of the If placement height may change due to PCB warp, use

2136

2137

PCB origin or of placement data.

PCB length is too short.

PCB warp tolerance" in the PCB data."

2138

2139

PCB thickness is out of spec.

The same offset value already exists in ST No. Offset.

2140 Still capture is selected.

To perform still capture, Z offset for vision process

must be entered in component advanced data.

Still capture and on-the-fly capture are prohibited to

2141

exist in one cycle. They will be divided into two

Multi view capture and on-the-fly capture are

2142 prohibited to exist in one cycle. They will be divided

into two cycles.

Pickup No. is not correct. (The feeder cannot be

2143

attached in the position.)

Check no obstacles at both sides of the feeder.

Select a fixed camera and do not use the scan

2144

2145

Component is too large and will hit the scan camera.

No fiducial mark process is found.

camera within this cycle.

Add fiducial mark steps.

2146 Original X and Y points of tray data are not entered.

Nozzle selection is not proper. It may cause pickup

Enter the coordinates of Original X and Y points of

tray data.

2147

error.

Check the nozzle No. and the component dimensions.

Sum of Pickup 'Z offset' + Feeder 'Feed height' +

2148

Cannot set the feeder because pickup point height

Package 'Height' must be 9mm or less. (Minus Z

exceeds 9mm.

offset is not added.)

2149

Cannot use F3 feeders and other type of feeders on

the same bank.

Check feeders.

2150 Comp Pitch is not proper. Select a proper Comp Pitch for the feeder.

2151 Dispense height is too low.

Dispense nozzle code is not registered in the

2152

dispense nozzle data.

2153

2154

Dispense check mode is not correct.

DotStation position is not proper.

Select Dispense & Check"."

2155

2156

Head does not reach DotStation. Mount DotStation at usable position.

Teach camera does not reach DotStation. Mount DotStation at usable position.

Create DotStation row in Pickup Data and specify

2157 DotStation is not registered in Pickup Data.

DotStation cannot be used in Placement data and

Station No.

2158

Component data.

2159 No global PCB warp check process is found. Add global PCB warp check process.

2160 The order of dispense and placement are not correct.

Correct the order so that dispense comes before

placement.

2161 Stacked component height exceeds 30mm.

2162 Syringe code is not registered in Dispense data.

Open Dispense from Manual menu and select Syringe

2163 Syringe code is not selected in Head Configuration.

code in Head Configuration.

2164 Dispense nozzle code is not registered in Syringe

More than one DotStation row is registered in Pickup

2165

data.

DotStation row must be one.

2166

2167

Laser head cannot reach DotStation.

Cannot mount DotStation because a feeder is within

the space.

Mount DotStation at proper position.

Relocate DotStation or the feeder.

2168 Dispense height is too high.

Maximum limit of dispensing and placement rows

2169

Total of dispensing and placement rows exceeds the

limit to perform Auto PCB warp check.

including repeat task rows is 10000 for Auto PCB

warp check. Select Manual for PCB warp check by

Figures (buffer/rigid) of Priority nozzle and Substitute

Same figure nozzle must be selected for Priority

2170

nozzle are different.

nozzle and Substitute nozzle.