M20_Ope_E - 第466页

2205 Program Check internal error 3000 PCB thickness error. Board data %d1 Measure result %d2 Tolerance %d3 3001 %s Elevator cannot work because the hook axis safety sensor is Off. Move the hook axis to the hook axis saf…

2171

Types of Priority nozzle and Substitute nozzle are

different.

Selection of Special Nozzle data of Priority nozzle

and Substitute nozzle must be the same.

2172 Coordinates of DotStation row cannot be changed. Keep coordinates of DotStaion 0.

2173 Components used in the program are not mounted.

2132

Check points in the same line zone for the global PCB

warp check is too close.

Distance between points must be wider than 5mm in

the same line zone.

Placement row exists prior to global PCB warp check

2133

rows.

Group No. of PCB warp check is specified prior to To use the same PCB warp check group, create PCB

2134

PCB warp check rows. warp check rows prior to placement rows.

2135 Group No. of PCB warp check is wrong. Available group Nos. of PCB warp check are 0-10000.

Data other than 0 is entered in Z coordiante of the If placement height may change due to PCB warp, use

2136

2137

PCB origin or of placement data.

PCB length is too short.

PCB warp tolerance" in the PCB data."

2138

2139

PCB thickness is out of spec.

The same offset value already exists in ST No. Offset.

2140 Still capture is selected.

To perform still capture, Z offset for vision process

must be entered in component advanced data.

Still capture and on-the-fly capture are prohibited to

2141

exist in one cycle. They will be divided into two

Multi view capture and on-the-fly capture are

2142 prohibited to exist in one cycle. They will be divided

into two cycles.

Pickup No. is not correct. (The feeder cannot be

2143

attached in the position.)

Check no obstacles at both sides of the feeder.

Select a fixed camera and do not use the scan

2144

2145

Component is too large and will hit the scan camera.

No fiducial mark process is found.

camera within this cycle.

Add fiducial mark steps.

2146 Original X and Y points of tray data are not entered.

Nozzle selection is not proper. It may cause pickup

Enter the coordinates of Original X and Y points of

tray data.

2147

error.

Check the nozzle No. and the component dimensions.

Sum of Pickup 'Z offset' + Feeder 'Feed height' +

2148

Cannot set the feeder because pickup point height

Package 'Height' must be 9mm or less. (Minus Z

exceeds 9mm.

offset is not added.)

2149

Cannot use F3 feeders and other type of feeders on

the same bank.

Check feeders.

2150 Comp Pitch is not proper. Select a proper Comp Pitch for the feeder.

2151 Dispense height is too low.

Dispense nozzle code is not registered in the

2152

dispense nozzle data.

2153

2154

Dispense check mode is not correct.

DotStation position is not proper.

Select Dispense & Check"."

2155

2156

Head does not reach DotStation. Mount DotStation at usable position.

Teach camera does not reach DotStation. Mount DotStation at usable position.

Create DotStation row in Pickup Data and specify

2157 DotStation is not registered in Pickup Data.

DotStation cannot be used in Placement data and

Station No.

2158

Component data.

2159 No global PCB warp check process is found. Add global PCB warp check process.

2160 The order of dispense and placement are not correct.

Correct the order so that dispense comes before

placement.

2161 Stacked component height exceeds 30mm.

2162 Syringe code is not registered in Dispense data.

Open Dispense from Manual menu and select Syringe

2163 Syringe code is not selected in Head Configuration.

code in Head Configuration.

2164 Dispense nozzle code is not registered in Syringe

More than one DotStation row is registered in Pickup

2165

data.

DotStation row must be one.

2166

2167

Laser head cannot reach DotStation.

Cannot mount DotStation because a feeder is within

the space.

Mount DotStation at proper position.

Relocate DotStation or the feeder.

2168 Dispense height is too high.

Maximum limit of dispensing and placement rows

2169

Total of dispensing and placement rows exceeds the

limit to perform Auto PCB warp check.

including repeat task rows is 10000 for Auto PCB

warp check. Select Manual for PCB warp check by

Figures (buffer/rigid) of Priority nozzle and Substitute

Same figure nozzle must be selected for Priority

2170

nozzle are different.

nozzle and Substitute nozzle.

2205 Program Check internal error

3000

PCB thickness error. Board data %d1 Measure result

%d2 Tolerance %d3

3001

%s Elevator cannot work because the hook axis safety

sensor is Off.

Move the hook axis to the hook axis safety sensor.

2174

Cannot set the feeder at the pickup station because

the feeder pickup point height exceeds the height of

limit range.

To set the feeder at a feeder station, 'ST-F1 to 13 on

M10', or 'ST-FR24 to 36 or ST-FL1 to 13 on M20',

feeder pickup point height, sum of Pickup 'Z offset' +

Feeder 'Feed height' + Package 'Height'" must be

2175

5mm or less. (Minus Z offset is not added.)"

Cannot set the feeder because Device Max Height of

To set the feeder at a pickup station, 'ST-F1 to 13 on

M10', or 'ST-FR24 to 36 or ST-FL1 to 13 on M20',

the feeder exceeds the height of limit range. sum of the device max height and the feeder height

must be 5mm or less.

The feeder cannot be set at the pickup station

2176 because sum of the device max height and the feeder

height exceeds 9mm.

2177

Cannot insert global PCB warp check rows within

repeat data.

Create global PCB warp check rows without using

repeat data.

2178

2179

The same dispense code exists.

The same syringe code exists.

Cannot register an existing code.

2180

2181

The same dispense nozzle code exists.

The auto pickup height calculation Auto8Paper" is

Cannot register an existing code.

Select other Package data.

not available for this feeder."

2182

Cannot use more than one Syringe code for the same

head.

Select proper Head No. and Syringe code for

dispensing.

2183

Other than 0 is entered in Nozzle Pitch for Single

Nozzle.

Enter 0 in Nozzle Pitch.

2184

2185

Dispense Nozzle Pitch is not entered.

1 Dot Image Type is selected for Twin Nozzle

Enter proper Nozzle Pitch.

Select 2 Dots or 4 Dots Image Type for Twin Nozzle

2186

Dispense check.

Offset of the Dispense check image and Nozzle pitch

Dispense check.

The difference of offset of Dispense check image and

2187

do not match.

Syringe code used in the program and Syringe code in

Nozzle pitch must be within +/-10%.

In Head Configuration, enter the same Syringe code

2188

Head Configuration do not match.

Twin Nozzle Angle and Dispense check image angle of

2 Dots do not match.

used in the program.

Align Twin Nozzle Angle and Dispense check image of

2 Dots.

2189

Other than 0 is entered in T of a dispense row for the

non-rotating twin nozzle.

Check that the data is correct.

2190

Other than 0 is entered in T Offset of the Offset &

Mode window that is related to a dispense row for the T offset data is ignored.

2191

non-rotating twin nozzle.

Nozzle code is not selected in Head Configuration.

Open Dispense from Manual menu and select Nozzle

2192

Nozzle code used in the program and Nozzle code in

code in Head Configuration.

Enter the same Nozzle code in Head Configuration

2193

Head Configuration do not match.

Dispense Check will not be executed because

used as in the program.

Check the Starting Dot and the Offset Count.

2194

Starting Dot is larger than Offset Count.

Placement/Dispensing coordinates are out of

Correct the coordinates.

2195

correction range of the 4-point Local PCB warp

Placement/Dispensing coordinates are out of

Correct the coordinates.

correction range of the Global PCB warp check.

2196

The placement height is lower than PCB height. It

may cause damage of PCB, components, or nozzles.

2197

Change the placement coordinates. Nozzles may hit

the conveyor.

2198

2199

The placement height is lower than the PCB surface.

The placement height is lower than the PCB bottom

2200

surface.

Dispense coordinates are located outside of the PCB

2201

dimensions partially.

Dispensing cannot be made because nozzle may hit

2202

the conveyor. Please change the dispense

Cannot perform Line Dispense because coordinates

of Start point and Stop point are the same.

2203

The position from PCB Front Edge is out of the

detection range.

2204

Component height exceeds the limit of Reject

Conveyor.

Component height must be lower than 5mm at the

front station and lower than 9mm at the rear station.

Result %d1 Default %d2 sure Z-axis moves smooth.

3039

The detected number of push-up pins and the

registered number of push-up pins do not match.

(Registered %d1: On Holder %d2: On Push-up Plate

Compare the number of push-up pins on the holder

and the registered number of pins.

3040 An error occurred while the CTF was initializing. Check the CTF.

3002

%s Origin recovery process is interrupted because

emergency stop is detected.

Check the machine condition and re-execute origin

recovery.

3003

3004

3005

%s Software limit over Specified coordinates are out of range.

Could not detect a mark on the conveyor rail. Check the mark condition.

Docking connector is not connected. %s %c1 Connect the CTF or the shorting plug to the mounter.

3006 Docking connector is disconnected. %s %c1

The CTF or the shorting plug is disconnected. Turn

off the mounter and check for any problems.

Difference of %s axis coordinates between the

3007 counter encoder and the motor encoder at the

machine startup exceeds the tolerance. Shift:%d1

Shift value of %s axis between the counter encoder

3008 and the motor encoder varied after machine startup.

Variation:%d1 Tolerance: %d2

3009

Shift value of the base mark exceeds the tolerance.

Shift:(%d1,%d2) Tolerance:(%d3,%d4) Check the base mark.

3010

Coodinates:(%d5,%d6)

Result of PCB check height exceeds the limit.

Check the warp check point.

Result:%v2mm, Default:%v3mm, Difference:%v1mm

3011

Head height result is not proper. Displacement: %d1,

Limit: %d2

Check the head and the base mark.

3012

3013

Head error occurred on the same head the height was

measured. Hence the measured height became invalid.

Cannot connect CTF during production.

When production is reset, head height will be

measured at next production.

Reset the production or connect CFB.

3014

Cannot perform conveyor height correction without a

Set a Nozzle 005 in the ANC.

Nozzle 005.

The mounter stopped by pickup error of the stick

Nozzle may hit a remaining component. Check the

3015 feeder %m %s-%d3 Head%c1 Nozzle%d2 Step:%d5

Offset:%d6

pickup point.

3016

3017

IO board connection error. Port%d1

Resume production from program row %d1 of repeat

3018

offset row %d2 by skipping row %m.

Height measurement error is found at result check.

Check that there is no debris at a measurement point.

3019 Nozzle did not reach the measurement height.

Also make sure Z-axis moves smooth.

Measurement height is too low or measurement point

3020

Cannot attach or remove the CFB/CTF when cover

is shifted.

Open the cover.

is closed.

3021

Nozzle damage alarm Head%c1 Nozzle%d2 Limit %d3 The nozzle vacuum pressure is not proper. Check the

3022

> %d4

Conveyor parallelism exceeds the tolerance. (Result):

nozzle.

Check the conveyor.

3023

%d1[Micrometer] > (Tolerance): +/- %d2[Micrometer]

CTF pallet transfer error Check the CTF.

3024 Fixed camera correction tool is not set. Set the fixed camera correction tool.

3025 Fixed camera correction tool cannot be recognized.

Check that no dirt or damage of the fixed camera

correction tool.

3026 Push-up pin is detected on the head %s.

Remove the push-up pin and the manipulator from

the head.

3027 Pin manipulator is not found. Replace the pin manipulator on the holder.

3028 The shutter of the pin manipulator is not open. Check the pin manipulator.

3029

3030

Pin manipulator fitting error (%e)

Pin manipulator remove error (%e)

Check the manipulator and the holder.

Check the pin manipulator on the head and remove it

3031 Push-up pin hold error (%e)

manually.

Check push-up pins on the holder.

3032 Push-up pin locate error Check push-up pins on the holder.

3033 Push-up pin remain error, Holder station %d1

Remove the push-up pin and the manipulator from

the head and check that no damage on them.

3034 Insufficient push-up pins (%d1>%d2)

Replace the registered number of push-up pins on the

holder.

3035

3036

No more places to replace push-up pins on the holder

Allocated push-up pins are not found on the push-up

Remove push-up pins from the holder.

3037

plate. (%d1,%d2)

Not all the allocated push-up pins can be replaced on

the holder. (%d1>%d2)

Check that no push-up pins laying on the push-up

plate.

3038

The height result exceeds the limit and is ignored. Check that no obstacles are at a check point. Make