MDO3000 Programmer Manual.pdf - 第101页

Command Groups T able 2-39: Search Commands (cont.) Command Description SEARCH:SEARCH<x>:TRIGger:A:LEV el:MA TH Sets the threshold level to use when searching on the math waveform. SEARCH:SEARCH<x>:TRIG ger:A…

100%1 / 1158
Command Groups
Table 2-39: Search Commands (cont.)
Command Description
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:US B:DATa:
SIZe
This command specifies the number of data bytes for USB searches
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:US B:DATa:
TYPe
This command specifies the data type for USB searches
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:US B:DATa:
VALue
This command specifies the data value for USB data searches
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:US B:
ENDPoint:VALue
This command specifies the endpoint value for USB searches
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:US B:
ERRTYPE
This command specifies the error type for USB searches
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:US B:
HANDSHAKEType
This command specifies the handshake type for USB searches
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:USB:QU ALifier This command specifies the qualifier for USB searches
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:US B:
SOFFRAME NU M ber
This command specifies the S OF number for USB searches
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:US B:
SPECIALType
This command specifies the special packet type for USB searches
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:US B:SPLit:E T:
VALue
When searching on a high-speed USB split transaction, this
command specifies the split transaction endpoint type value to
search for.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:US B:SPLit:
HUB:VALue
When searching on a high-speed USB split transaction, this
command specifies the split transaction hub address value to
search for.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:US B:SPLit:
PORT:VALue
When searching on a high-speed USB split transaction, this
command specifies the split transaction port address value to
search for.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:US B:SPLit:SC:
VALue
When searching on a high-speed USB split transaction, this
command specifies whether to search for the start or complete
phase of the split transaction, based on the Start/Complete bit field
value.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:US B:SPLit:S E:
VALue
When searching for a high-speed USB split transaction, this
command specifies the split transaction start/end bit value to search
for.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:US B:
TOKENType
This command specifies the token type for USB searches
SEARCH:SEARCH<x>:TRIGger:A:BUS:SOU rc e This command specifies the bus for a serial search
SEARCH:SEARCH<x>:TRIGger:A:EDGE:SLOpe This command specifies the slope to be used in an edge search:
rising, falling or either
SEARCH:SEARCH<x>:TRIGger:A:EDGE:SOUrce This command specifies the source waveform for an edge search
SEARCH:SEARCH<x>:TRIGger:A:LEVel:CH<x>
Sets the threshold level to use when searching on an analog
waveform.
2-70 MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual
Command Groups
Table 2-39: Search Commands (cont.)
Command Description
SEARCH:SEARCH<x>:TRIGger:A:LEVel:MATH
Sets the threshold level to use when searching on the math
waveform.
SEARCH:SEARCH<x>:TRIGger:A:LEVel:REF<x>
Sets the threshold level to use when searching on a reference
waveform.
SEARCH:SEARCH<x>:TRIGger:A:LEVel:RF_AMPlitude
Sets the threshold level to use when searching on the RF Amplitude
vs. Time trace.
SEARCH:SEARCH<x>:TRIGger:A:LEVel:RF_FREQuency
Sets the threshold level to use when searching on the RF Frequency
vs. Time trace.
SEARCH:SEARCH<x>:TRIGger:A:LEVel:RF_PHASe
Sets the threshold level to use when searching on the RF Phase
vs. Time trace.
SEARCH:SEARCH<x>:TRIGger:A:LOGIc:FU NCtion Specifies the logic operator to be used in a logic search.
SEARCH:SEARC H<x>:T RIG ger:A:LO G Ic:PATtern:INPut:
CH<x>
This command specifies the logic operator for the logic search
SEARCH:SEARC H<x>:TRIGger:A:LOGIc:INPut:CH<x> Specifies the l ogic condition to be used in a logic search when the
input is an analog channel.
SEARCH:SEARC H<x>:TRIGger:A:LOGIc:INPut:CLOCk:
EDGE
This command specifies whether the clock edge is rise or fall for
a logic search
SEARCH:SEARC H<x>:TRIGger:A:LOGIc:INPut:CLOCk:
SOUrce
This command specifies the clock source de finition for logic search
SEARCH:SEARC H<x>:TRIGger:A:LOGIc:INPut:D<x> This command specifies the criteria for a logic search to determine
where to place a mark for digital channel <x>
SEARCH:SEARC H<x>:T RIG ger:A:LO G Ic:IN Put:M ATH This command specifies the Boolean logic criteria for the logic
search
SEARCH:SEARC H<x>:T RIG ger:A:LOGIc:INPut:REF<x> This command specifies the Boolean logic criteria for the logic
search
SEARCH:SEARCH<x>:TRIGger:A:LOGIc:INPut:
RF_AMPlitude
This command specifies the logic criteria to search for when
searching using the RF Amplitude vs. Time trace. This command
is used together with SEARCH:SEARCH<x>:TRIGger:A:LOGIc:
THReshold:RF_AMPlitude to search for an instance when the
waveform goes higher or lower than the specified threshold.
SEARCH:SEARCH<x>:TRIGger:A:LOGIc:INPut:
RF_FREQuency
This command specifies the logic criteria to search for when
searching using the RF Frequency vs. Time trace. This command
is used together with SEARCH:SEARCH<x>:TRIGger:A:LOGIc:
THReshold:RF_FREQuency to search for an instance when the
waveform goes higher or lower than the specified threshold.
SEARCH:SEARC H<x>:TRIGger:A:LOGIc:INPut:RF_PHAS e This command speci fies the logic criteria to search for when
searching using the RF Phase vs. Time trace. This command
is used together with SEARCH:SEARCH<x>:TRIGger:A:LOGIc:
THReshold:RF_PHASe to search for an instance when the
waveform goes higher or lower than the specified threshold.
SEARCH:SEARC H<x>:T RIG ger:A:LO G Ic:PATtern:WHEn This command specifies the condition for generating a logic pattern
search.
MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual 2-71
Command Groups
Table 2-39: Search Commands (cont.)
Command Description
SEARCH:SEARCH<x>:TRIGger:A:LOGIc:PATtern:WHEn:
LESSLimit
This command specifies the maximum time that the selected pattern
may be true.
SEARCH:SEARCH<x>:TRIGger:A:LOGIc:PATtern:WHEn:
MORELimit
This command specifies the minimum tim e that the selected pattern
may be true.
SEARCH:SEARCH<x>:TRIGger:A:LOGIc:THReshold:CH<x> This command specifies the channel threshold level for a logic
search.
SEARCH:SEARCH<x>:TRIGger:A:LOGIc:THReshold:MATH This command specifies the math waveform threshold level for a
logic search.
SEARCH:SEARCH<x>:TRIGger:A:LOGIc:THReshold:
REF<x>
This command specifi es the reference w aveform threshold level
for a logic search
SEARCH:SEARCH<x>:TRIGger:A:LOGIc:THReshold:
RF_AMPlitude
This command specifies the threshold to use when searching the
RF Amplitude vs. Time waveform. (Same as the command
SEARCH:SEARCH<x>:TRIGger:A:LOWerthreshold:RF _AMPlitude.)
This command is used together with
SEARCH:SEARCH< x>:TR IGger:A:LOG Ic:IN Put:RF _AM Plitude to
search for an instance when the RF Amplitude vs. Time waveform
goes higher or lower than the s pecifi ed threshold.
SEARCH:SEARCH<x>:TRIGger:A:LOGIc:THReshold:
RF_FREQuency
This command specifies the threshold to use
when searching the RF Frequency vs. Time
waveform. (It does the same thing as the command
SEARCH:SEARCH<x>:TRIGger:A:LOWerthreshold:RF _FREQuency.)
This command is used together with
SEARCH:SEARCH<x>:TRIGger:A:LOGIc:INPut:RF_FREQuency
to search for an instance when the R F Frequency vs. Time
waveform goes higher or lower than the specified threshold.
SEARCH:SEARCH<x>:TRIGger:A:LOGIc:THReshold:
RF_PHASe
This command specifies the threshold, in degrees, to use when
searching the RF Phase vs. Time waveform. (It does the same thing
as
SEARCH:SEARCH<x>:TRIGger:A:LOWerthreshold:RF _PHASe.)
This command is used together with
SEARCH:SEARCH< x>:TR IGger:A:LOG Ic:IN Put:RF _PH ASe to
search for an instance when the RF Phase vs. Time waveform goes
higher or lower than the specified threshold.
SEARCH:SEARCH<x>:TRIGger:A:LOWerthreshold:CH<x> This command specifies the lower waveform threshold level for
all channel waveform searches
SEARCH:SEARCH<x>:TRIGger:A:LOWerthreshold:MATH This command specifies the lower waveform threshold level for all
math waveform searches
SEARCH:SEARCH<x>:TRIGger:A:LOWerthreshold:REF<x> This command specifies the lower waveform threshold level for all
reference waveform searches
SEARCH:SEARCH<x>:TRIGger:A:LOWerthreshold:
RF_AMPlitude
This command specifies the threshold for RF Amplitude vs.
Time trace searches. For runt and transition searches, this
level is the lower threshold. For other search types, this is
the single threshold. This command is used together with
SEARCH:SEARCH< x>:TR IGger:A:LOG Ic:IN Put:RF _AM Plitude to
search for an instance when the waveform goes higher or lower
than the specified threshold.
2-72 MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual