MDO3000 Programmer Manual.pdf - 第1130页

Appendix H: List of Beta Commands and Features T e k t r o n i xt oc o mply with any additional obligatio ns with respect to any T ektronix products or services that incor porate any feedb ack. Command List T a b l eH - …

100%1 / 1158
Appendix H: List of Beta Commands and Features
This section lists and documents commands and features designated as beingin
a “beta” state. The following disclaimer applies to all commands and features
documented i
n this appendix.
Legal Disclaimers
Disclaimer
Features d
esignated “Alpha” or “Beta” are provided on an "as is" and unsupported
basis. The Alpha and Beta features have not been fully tested, and may contain
defects. Use of these features is at your own risk and may void the warranty on
your product. You shall bear the entire risk as to the quality and performance of
the Alpha or Beta features. Should any Alpha or Beta feature prove defective, you
assume the cost of all necessary servicing, repair, or correction. You should not
rely in a
ny way on the correct performance of any Alpha or Beta feature. You are
advised to safeguard important data before using any Alpha or Beta feature.
Tektro
nix disclaims any and all other warranties for use of any Alpha or Beta
feature, whether express or implied, including without limitation any implied
warranties of merchantability or fitness for a particular purpose, to the extent
authorized by law. Without limitation of the foregoing, Tektronix expressly does
NOT warrant that the Alpha or Beta features will meet your requirements, will
perform as described, or will be error free.
Tektronix will not be liable for any loss (whether direct or indirect, consequential
or special) suffered by any party as a result of the use of or inability to use any
Alp
ha or Beta feature (including but not limited to loss of data, data being rendered
inaccurate, or failure of the Alpha or Beta feature to operate with any other
programs), even if Tektronix has been advised of the possibility of such damages.
No Support for Alpha or
Beta Features
A
lpha and Beta features are unsupported. Tektronix is under no obligation to
provide technical support for any Alpha or Beta feature. Tektronix is not obliged
to support, repair, continue to develop, or continue to provide any Alpha orBeta
feature. Tektronix may change or remove any or all Alpha and Beta features at
any time without notice.
Alpha and Beta Feature
Feedback
You may choose to provide feedback (including suggestions, comments, or
other feedback) to Tektronix regarding the Alpha and Beta commands. You
hereby agree that you will grant Tektronix a worldwide, non-exclusive, perpetual,
irrevocable, royalty-free right to (i) make, use, copy, modify, sell, distribute,
sublicense, and create derivative works of the feedback as part of any Tektronix
product, service, or documentation, (ii) publically perform or display, import
broadcast, transmit, distribute, license, offer to sell, sell, or rent copies of the
feedback, and (iii) sublicense these rights to third parties. You warrantythat
your feedback is not subject to any license terms that would purportedly require
MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual H-1
Appendix H: List of Beta Commands and Features
Tektronixtoco
mply with any additional obligations with respect to any Tektronix
products or services that incorporate any feedback.
Command List
TableH-1:PresentlyAvailableBetaCommands
Feature
Associated Commands
AFG run commands AFG:RUNMode
AFG trigger
commands
AFG:TRIGger
AFG:TRIGger:MODe
AFG:TRIGger:SOUrce
AFG:TRIGger:POLarity
AFG:TRIGger:COUnt
AFG:TRIGger:INTerval
AFG:TRIGger:DELay
AFG modulation
commands
AFG:MODULation:TYPeAFG:MODULation:TYPe
AFG:MODULation:AM:WAVeform
AFG:MODULation:AM:FREQuency
AFG:MODULation:AM:DEPth
AFG:MODULation:FM:WAVeform
AFG:MODULation:FM:FREQuency
AFG:MODULation:FM:DEViation
Beta Commands Listed in A lphabetical Order
AFG:MODULation:AM:DEPth
Description:
Sets the modulation depth to use for Amplitude Modulation for the AFG.
Con
ditions:
Beta Command, see conditions of use. Default setting is 50.0.
Group:
AFG
Syntax:
AFG:MODULation:AM:DEPth <NR3>
AFG:MODULation:AM:DEPth?
Arguments:
<NR3> - Depth value in percent from 0.0 to 100.0 with a resolution of 0.1%.
H-2 MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual
Appendix H: List of Beta Commands and Features
Examples:
AFG:MODULatio
n:AM:DEPth
10.0 sets the modulation depth to 10%.
AFG:MODULation:AM:FREQuency
Description:
Sets the modulation frequency to use for Amplitude Modulation for the AFG.
Conditions:
Beta Command, see conditions of use. Default setting is 10.0E+3.
Group:
AFG
Syntax:
AFG:MODULation:AM:FREQuency <NR3>
AFG:MODULation:AM:FREQuency?
Arguments:
<NR3> - Frequency value for modulation in Hz from 200.0E-3 to 50.0E+3 with a
resolution of 100.0E-3.
Example
s:
AFG:MODULation:AM:FREQuency 10.0E+3 sets the modulation frequency to
10kHz.
AFG:MODULation:AM:WAVeform
Description:
Sets the modulation shape to use for Amplitude Modulation for the AFG.
Conditions:
Beta Command, see conditions of use. Default setting is SINE.
Group:
AFG
Syntax:
AFG:MODULation:AM:WAVeform
{SINE|SQUare|TRIangle|RAMP|NRAMP|NOISe}
AFG:MODULation:AM:WAVeform?
Arguments:
SINE -Sinewaveform
SQUare - Square waveform
TRIangle - Triangle waveform
RAMP - Positive ramp waveform
MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual H-3