MDO3000 Programmer Manual.pdf - 第124页

Command Groups T able 2-42: V ertical Commands (cont.) Command Description REF<x>:HORizontal:SCAle This command speci ﬁ es the horizontal scale for a reference w aveform REF<x>:LABel This command speci ﬁ es t…

Command Groups

Table 2-42: Vertical Commands (cont.)

Command Description

CH<x>:PRObe:CALibrate:STATE? This query returns the calibration state of the probe connected to the speciﬁed

channel.

CH<x>:PRObe:COMMAND Sets the state of the speciﬁ ed probe control

CH<x>:PRObe:DEGAUss Starts a degauss/autozero cycle on a TekVPI current probe attached to the

speciﬁed channel input

CH<x>:PRObe:DEGAUss:STATE? Returns the state of the probe degauss

CH<x>:PRObe:FORCEDRange This command speciﬁes the range on a TekVPI probe attached to the speciﬁed

channel

CH<x>:PRObe:GAIN This command speciﬁes the gain factor of the probe that is attached to the

speciﬁed channel

CH<x>:PRObe:ID? Returns the type and serial number of the probe that is attached to the

speciﬁed channel

CH<x>:PRObe:ID:SERnumber? Returns the serial number of the probe that is attached to the speciﬁed channel

CH<x>:PRObe:ID:TYPe? Returns the type of probe that is attached to the speciﬁed channel

CH<x>:PRObe:MODel This command speciﬁes the probe model for the speciﬁed channel

CH<x>:PRObe:PROPDELay This command speciﬁes the propagation delay for the probe connected to

the speciﬁed channel

CH<x>:PRObe:RECDESkew? Returns the recommended deskew for the probe connected to the speciﬁed

channel

CH<x>:PRObe:RESistance? Returns the resistance of the probe that is attached to the speciﬁed channel

CH<x>:PRObe:SIGnal This command speciﬁes the input bypass setting of channel <x>TekVPI probe

CH<x>:PRObe:UN Its? Returns the units of measure of the probe that is attached to the speciﬁed

channel

CH<x>:SCAle This command speciﬁes the vertical scale of the speciﬁed channel

CH<x>:TERmination This command speciﬁes channel input termination

CH<x>:YUNits This command speciﬁes the units for the speciﬁed channel

D<x>

Returns parameters for digital channel <x>

D<x>:LABel

This command speciﬁes the waveform label for digital channel<x>

D<x>:THReshold

This command speciﬁes the logical threshold for the digital channel <x>, where

x is the digital channel number D0 – D15.

D<x>:POSition This command speciﬁes the vertical position for digital channel <x>

DESkew Causes the deskew values for all channels to be set to the recommended

values

DESkew:DISPlay Speciﬁes the state of the deskew table display.

DISplay:INTENSITy:BACKLight:AUTODim:TIMe This command speciﬁes the state of the deskew table display

REF<x>? Returns reference waveform data for channel <x>

REF<x>:DATE? Returns the date that a reference waveform was stored

REF<x>:HORizontal:DELay:TIMe This command speciﬁes the horizontal position of the speciﬁed reference

waveform in percent of the waveform that is displayed to the right of the center

vertical graticule

MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual 2-93

Command Groups

Table 2-42: Vertical Commands (cont.)

Command Description

REF<x>:HORizontal:SCAle This command speciﬁes the horizontal scale for a reference w aveform

REF<x>:LABel

This command speciﬁes the speciﬁed reference waveform label

REF<x>:TIMe? Returns the time that a reference waveform was stored

REF<x>:VERTical:POSition This command speciﬁes the vertical position of the speciﬁed reference

waveform

REF<x>:VERTical:SCAle This command speciﬁes the reference waveform vertical scale in vertical

units/div

SELect? Returns information on which waveforms are on or off and which waveform

is selected.

SELect:{BUS<x>|B<x>} Turnsonoroffthespeciﬁed bus waveform or returns whether the speciﬁed

bus channel is on or off

SELect:CH<x> Turnsonoroffthespeciﬁed waveform or returns whether the speciﬁed

channel is on or off

SELect:CONTROl This command speciﬁes the waveform that is selected as the implied recipient

of channel-related commands

SELect:DAll This command turns on or off all digital channels (D0 — D15).

SELect:D<x> Turns on the display of digital channel <x> and resets the acquisition

SELect{:MATH|:MATH1} Turns on or off the math waveform or returns whether the math waveform is

on or off

SELect:REF<x> Turnsonoroffthespeciﬁed reference waveform or returns whether the

speciﬁed reference waveform is on or off

VideoPictureCommandGroup

The video picture features as well as triggering on a video signal are included

standard with the MDO3000 series models. These features require the DPO4VID

application module for use with MSO/DPO4000B and the MDO4000/B/C models.

Use the video picture commands for video picture functionality.

Table 2-43: Video Picture Commands

Command Description

VIDPic:AUTOContrast Sets (or queries) the video picture automatic contrast state.

VIDPic:AUTOContrast:UPDATERate Sets (or queries) the number of frames between automatic contrast updates

VIDPic:BRIGHTNess Sets (or queries) the video picture brightness level as an integer percentage.

VIDPic:CONTRast Sets (or queries) the video picture contrast level as an integer percentage.

VIDPic:DISplay Sets (or queries) the video picture display state.

VIDPic:FRAMETYPe

Sets (or queries) the video picture frame type (O DD, EVEN or INTERLAced).

VIDPic:LOCation:HEIght Sets (or queries) the video picture height, in rows.

2-94 MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual

Command Groups

Table 2-43: Video Picture Commands (cont.)

Command Description

VIDPic:LOCation:OFFSet Sets (or queries) the video picture line-to-line offset. This is the amount of

additional delay time to add between lines of the video picture.

VIDPic:LOCation:STARt:LINE Sets (or queries) the video picture starting l ine number.

VIDPic:LOCation:STARt:PIXel Sets (or queries) the video picture starting pixel in each line

VIDPic:LOCation:WIDth Sets (or queries) the video picture width, in columns.

VIDPic:LOCation:X Sets (or queries) the video picture X origin location, in columns.

VIDPic:LOCation:Y Sets (or queries) the video picture Y origin location, in rows.

VIDPic:SOUrce Sets (or queries) the channel to use for the video picture source waveform.

VIDPic:STANdard Sets (or queries) which video picture standard to use (either NTSC or PAL).

Wa veform Transfer Command Group

(See Table 2-48.)

The

CURVe and other commands and queries in the Waveform Transfer Command

Group are used to transfer waveform data points to and from the oscilloscope.

Thewaveformdatapointsareacollectionofvaluesthatrepresenttheamplitude

of the waveform samples. One data value usually represents one data point inthe

veform record. Only one waveform can be transferred at a time.

Each waveform you transfer has an associated waveform preamble, which

ontains information such as data format, horizontal scale, vertical scale, and the

other settings in effect when the waveform was created. When you transfer a

waveform, you need to specify at least some of the general and preamble settings

(using the

DATa, WF MInpre or WFMOutpre commands) before you specify the

raw data point information (using the

CURVe command or query.)

Waveform data can be transferred to or from the oscilloscope using the Ethernet

or USBTMC interfaces in binary or ASCII format. Binary data transfer is

considerably more efﬁcient than ASCII data transfer. Binary data is transferred to

and from the oscilloscope using the IEEE488.2 arbitrary block format (7.7.6 of

the IEEE488.2 spec) which we refer to in this document as “binary block format”.

A binary block is represented as:

#N<N-Digits><binary data>

Where:

The “#” is the arbitrary block token.

N is a single hexadecimal digit specifying how many decimal digits

immediately follow.

<N-Digits> is a decimal number N digits long, that speciﬁes the number of

binary data bytes to follow.

MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual 2-95