MDO3000 Programmer Manual.pdf - 第18页

Getting Started T able 1-1: U pdates to the MDO3000 and MDO4000C Series Oscilloscopes (cont.) Feature Use these comm ands Video Picture functionality ( standard on MDO3000). R equires the D PO4V ID application module for…

100%1 / 1158
Getting Started
Table 1-1: Updates to the MDO3000 and MDO4000C Series Oscilloscopes (cont.)
Feature Use these comm ands
Digital Voltmeter functionality (MDO 3000 and
MDO4000C series only)
DVM
DVM:AUTORange
DVM:DISPLAYSTYle
DVM:MEASUrement:FREQuency?
DVM:MEASUrement:HIStory:AVErage?
DVM:MEASUrement:HIStory:MAXimum?
DVM:MEASUrement:HIStory:MINImum?
DVM:MEASUrement:INFMAXimum?
DVM:MEASUrement:INFMINimum?
DVM:MEASUrement:VALue?
DVM:MODe
DVM:SOUrce
Act on Event functionality
Available actions:
–Stopacquisitions
– Save waveform data to a file
– Save a screen image to a file
– Send a screen image to a printer
– Send a pulse to the Aux Out port
– Generate a service request
– Send an email
– Display a visual notification
Available events:
– Upon trigger
– When a certain number of acquisitions have completed
– N one
ACTONEVent:ACTION:AUXOUT:STATE
ACTONEVent:ACTION:PRINT:STATE
ACTONEVent:ACTION:SAVEIMAGE:STATE
ACTONEVent:ACTION:SAV EWFM:STATE
ACTONEVent:ACTION:SRQ:STATE
ACTONEVent:REP EATCount
ACTONEVent:ACTION:VISUAL:STATE
ACTONEVent:EVENTTYPe
ACTONEVent:NUMACQs
ACTONEVent:REP EATCount
Email settings for both email printer support and Act on Event
“send an email” action
EMAIL:SETUp:FROMADDRess
EMAIL:SETUp:HOSTALIASNAMe
EMAIL:SETUp:SMTPLOGIn
EMAIL:SETUp:SMTPPASSWord
EMAIL:SETUp:SMTPPort
EMAIL:SETUp:SMTPServer
MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual 1-5
Getting Started
Table 1-1: Updates to the MDO3000 and MDO4000C Series Oscilloscopes (cont.)
Feature Use these comm ands
Video Picture functionality (standard on MDO3000). R equires
the D PO4VID application module for use with MSO/DPO4000B
and MDO4000/B/C models)
VIDPic:AUTOContrast
VIDPic:AUTOContrast:UPDATERate
VIDPic:BRIGHTNess
VIDPic:CONTRast
VIDPic:DISplay
VIDPic:FRAMETYPe
VIDPic:LOCation:HEIght
VIDPic:LOCation:OFFSet
VIDPic:LOCation:STARt:LINE
VIDPic:LOCation:STARt:PIXel
VIDPic:LOCation:WIDth
VIDPic:LOCation:X
VIDPic:LOCation:Y
VIDPic:SOUrce
VIDPic:STANdard
Dual edge trigger/search functionality TRIGger:A:EDGE:SLOpe
SEARCH:SEARCH<x>:TRIGger:A:EDGE:SLOpe
FastAcq™ high-speed waveform acquisition mode
New color palettes (Temperature, Spectral, Normal, Inverted)
ACQuire:FASTAcq:STATE
ACQuire:FASTAcq:PALEtte
Digital C hannel Activity Monitor DISplay:DIGital:ACTIVity
Additional calibration status queries
CALibrate:INTERNal:STATus:RF?
CALibrate:INTERNal:STATus:SCOPE?
CALibrate:RESults:FACtory:AFG ?
CALibrate:RESults:FACtory:RF?
CALibrate:RESults:FACtory:SCOPE?
CALibrate:RESults:SPC:RF?
CALibrate:RESults:SPC:SCOPE?
Additional configuration queries
(AFG, ARB, DVM, and VidPic are available for MDO 3000 and
MDO4000C series. VidPic requires the DPO4VID application
module on the MSO/DPO4000B and MDO4000/B/C models)
CONFIGuration:AFG?
CONFIGuration:APPLications:CUSTOMMask?
CONFIGuration:APPLications:STANDARDMask?
CONFIGuration:APPLications:VIDPIC?
CONFIGuration:ARB?
CONFIGuration:DVM?
Math vertical autoscale feature MATH[1]:AUTOSCale
Total overshoot measurement type
MEASUrement:IMMed:TYPe
MEASUrement:MEAS<x>:TYPe
1-6 MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual
Getting Started
Table 1-1: Updates to the MDO3000 and MDO4000C Series Oscilloscopes (cont.)
Feature Use these comm ands
Additional RF Spectrogram and Spectrum Trace commands RF:SPECTRogram
RF:SPECTRogram:SLICETIMe?
RF:SPECTRogram:TIMe?
RF:SPECTRUMTrace
Ability to save RF baseband I & Q data to a M atlab level 5
file or .TIQ file
SAVe:WAVEform:FILE Format:RF_BB_IQ
Table 1-2: Updates to the MDO3000 and MDO4000C Series Oscilloscopes
Feature Use these commands
System reboot REBOOT
CANFDbusconfiguration CONFIGuration:BUSWAVEFORMS:CANFD?
BUS:B<x>:CAN:FD:STANDard
BUS:B<
x>:CAN:FD:BITRate
BUS:B<x>:CAN:STANDard
BUS:B<x>:DISplay:FORMat
Can F D search criteria SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CAN:CONDition
SEARC
H:SEARCH<x>:TRIGger:A:BUS:B<x>:CAN:DATa:OFFSet
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CAN:FD:BRSBIT
SEARCH:SEARC H<x >:T R IGger:A:BUS:B<x>:CAN:FD:ESIBIT
CAN FD trigger TRIGger:A:BUS :B<x>:CAN:CONDition
TRI
Gger:A:BUS:B<x>:CAN:D ATa:OFFSet
TRIGger:A:BUS :B<x>:CAN:FD:BRSBIT
TRIGger:A:BUS :B<x>:CAN:FD:ESIBIT
SettingUpRemoteCommunicationsHardware
Yo
u can remotely control communications between your oscilloscope and a PC
via Ethernet, USB, or GPIB cables.
Ethernet
If you are using Ethernet, start by connecting an appropriate Ethernet cable to the
Ethernet port (RJ-45 connector) on the rear panel of your oscilloscope. This
connects the oscilloscope to a 10BASE-T/100BASE-TX/1000BASE-T local area
network.
MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual 1-7