MDO3000 Programmer Manual.pdf - 第820页

Commands Listed in A lphabetical Order TRIGger:A:BU S:B<x>:CAN:DA T a:V ALue This command sets the binary data v alue to be used when triggering on a CAN bus signal. The trigger condition must be set to IDANDDA T A…

100%1 / 1158
Commands Listed in Alphabetical Order
Syntax
TRIGger:A:BUS
:B<x>:CAN:DATa:QUALifier
{LESSthan|Than|EQual|UNEQual|LESSEQual|EQual}
TRIGger:A:BUS:B<x>:CAN:DATa:QUALifier?
Arguments
LESSthan sets the oscilloscope to trigger when the data is less than the qualifier
value.
Than sets the oscilloscope to trigger when the data is than the qualifier value.
EQual sets the oscilloscope to trigger when the data is equal to the qualifier value.
UNEQual sets the oscilloscope to trigger when the data is not equal to the qualifier
value.
LESSEQual sets the oscilloscope to trigger when the data is less than or equal
to the qualifier value.
EQual sets the oscilloscope to trigger when the data is than or equal to the
qualifier value.
Examples
TRIGGER:A:BUS:B1:CAN:DATA
:QUALIFIER LESSTHAN
sets the oscilloscope
to trigger when the data is less than the qualifier value.
TRIGGER:A:BUS:B1:CAN:DAT
A:QUALIFIER?
might return
:TRIGGER:A:BUS:B1:CAN:DATA:QUALIFIER THAN, indicating that the
oscilloscope is set to trigger when the data is than the qualifier value.
TRIGger:A:BUS:B<x>:CAN
:DATa:SIZe
This command sets the length of the data string, in bytes, to be used when
triggering on a CAN bus signal. The trigger condition must be set to
IDANDDATA OR DATA (usin
g TRIGger:A:BUS:B<x>:CAN:CONDition).
B<x> is the bus number (1-4). 1-3 for the MDO4000C and 1-2 for the MDO3000.
Conditions
This command requires a DPO4AUTO or DPO4AUTOMAX application module
on DPO/MSO4000B and MDO4000/B/C models and a MDO3AUTO application
module on MDO3000 models.
Group
Trigger
Syntax
TRIGger:A:BUS:B<x>:CAN:DATa:SIZe <NR1>
TRIGger:A:BUS:B<x>:CAN:DATa:SIZe?
Arguments
<NR1> is the length of the data string in bytes.
MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual 2-789
Commands Listed in Alphabetical Order
TRIGger:A:BU
S:B<x>:CAN:DATa:VALue
This command sets the binary data value to be used when triggering on a CAN
bus signal. The trigger condition must be set to IDANDDATA OR DATA (using
TRIGger:A:B
US:B<x>:CAN:CONDition).
B<x> is the bus number (1-4). 1-3 for
the MDO4000C and 1-2 for the MDO3000.
Conditions
This command requires a DPO4AUTO or DPO4AUTOMAX application module
on DPO/MSO4000B and MDO4000/B/C models and a MDO3AUTO application
module on MDO3000 models.
Group
Trigger
Syntax
TRIGger:A:BUS:B<x>:CAN:DATa:VALue <QString>
TRIGger:A:BUS:B<x>:CAN:DATa:VALue?
Arguments
<QString> is the data value in binary format. The only allowed characters in
the
QString are0,1,andX.
Examples
TRIGGER:A:BUS:B1:CAN:DATA:VALUE 1011 sets the CAN data value to 1011.
TRIGger:A:BUS:B<x>:CAN:FD:BRSBIT
This command specifies the binary data value to be used to search on CAN FD
BRS bits. This only applies if the search condition has been set to FDBRSBIT
(using
TRIGger:A:BUS:B<x>:CAN:CONDition).
B<x> is the bus number (1-3) for the MDO4000C and 1-2 for the MDO3000.
Conditions
This command requires a DPO4AUTO or DPO4AUTOMAX application module
on MDO4000C models and a MDO3AUTO application module on MDO3000
models.
Group
Search
Syntax
TRIGger:A:BUS:B<x>:CAN:FD:
BRSBIT{ZERo|OFF|0|ONE|ON|1|NOCARE|X|x}
TRIGger:A:BUS:B<x>:CAN:FD:BRSBIT?
Related Commands
TRIGger:A:BUS:B<x>:CAN:CONDition
2-790 MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual
Commands Listed in Alphabetical Order
Arguments
ZERo, OFF,and0
specify that the BRS bit must have value 0. If queried, the
command will always return 0 if set with these arguments.
ONE, ON,and1 specify that the BRS bit must have value 1. If queried, the
command will always return 1 if set with these arguments.
NOCARE, X,andx specify that the BRS bit may be either 1 or 0. If queried, the
command will always return X if set with these arguments.
TRIGger:A:BUS:B<x>:CAN:FD:ESIBIT
This command specifies the binary data value to be used to search on CAN FD
ESI bits. This only applies if the search condition has been set to FDESIBIT
(using
TRIGger:A:BUS:B<x>:CAN:CONDition).
B<x> is the bus number (1-3), except for the MDO3000 which only has two buses.
Conditions
This command requires a DPO4AUTO or DPO4AUTOMAX application module
on MDO4000C models and a MDO3AUTO application module on MDO3000
models.
Group
Search
Syntax
TRIGger:A:BUS:B<x>:CAN:FD:
ESIBIT{ZERo|OFF|0|ONE|ON|1|NOCARE|X|x}
TRIGger:A:BUS:B<x>:CAN:FD:ESIBIT?
Related Commands
TRIGger:A:BUS:B<x>:CAN:CONDition
Arguments
ZERo, OFF,and0 specify that the BRS bit must have value 0. If queried, the
command will always return 0 if set with these arguments.
ONE, ON,and1 specify that the BRS bit must have value 1. If queried, the
command will always return 1 if set with these arguments.
NOCARE, X,andx specify that the BRS bit may be either 1 or 0. If queried, the
command will always return X if set with these arguments.
TRIGger:A:BUS:B<x>:CAN:FRAMEtype
This command sets the frame type (data, remote, error or overload) to be used
when triggering on a CAN bus signal. The trigger condition must be set to
FRAMEtype (using TRIGger:A:BUS:B<x>:CAN:CONDition).
B<x> is the bus
number (1-4). 1-3 for the MDO4000C and 1-2 for the MDO3000.
MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual 2-791