MDO3000 Programmer Manual.pdf - 第93页

Command Groups T able 2-39: Search Commands (cont.) Command Description SEARCH:SEARCH<x>:TRIGger :A:BUS:B<x>:ARINC429A: CONDition This command sets the condition to use w hen searching on ARINC429 bus data (w…

100%1 / 1158
Command Groups
Bus, Video, and RF
application modules
A table is avail
able that lists all commands enabled by each application module
(See page H-1, List of Beta Commands and Features.)
For I
2
C or SPI bus signals, install the DPO4EMBD application module,
except for M
DO3000 models, which require MDO3EMBD.
For RS-232, RS-422, RS-485, or UART bus signals, install the DPO4COMP
module, except for MDO3000 models, which require MDO3AUDIO.
For I
2
S, Left Justified (LJ), Right Justified (RJ), or TDM bus signals, install
the DPO4AUDIO module, except for MDO3000 models, which require
MDO3AUDIO.
For CAN, CAN FD, or LIN bus signals, install the DPO4AUTO or
DPO4AUTOMAX module, except for MDO3000 models, which require
MDO3AUTO.
For FlexRay bus signals, install the DPO4AUTOMAX module, except for
MDO3000 models, which require MDO3FLEX.
For Ethernet signals, when tested with the MDO4000/B/C and
MSO/DPO4000B, install the DPO4ENET module. Note that ≥350 MHz
bandwidth models are recommended for 100BASE-TX.
For MIL-STD-1553 or ARINC429 bus signals, install the DPO4AERO
module, except for MDO3000 models, which require MDO3AERO.
For USB bus signals, install the DPO4USB module, except for MDO3000
models, which require MDO3USB. Note that 1 GHz bandwidth models are
recommended for high-speed (HS) USB.
For video signals, install the DPO4VID module, except for the MDO3000
models, which do not require a module.
For RF signals (MDO4000/B/C Series only), install the MDO4TRIG module.
Table 2-39: Search Commands
Command Description
SEARCH?
Returns all search-related settings
SEARCH:SEARCH<x>:COPy Copies the search criteria to the trigger, or the trigger criteria to
the search
SEARCH:SEARCH<x>:LIST? This query returns a list of all automatically created search marks
on waveforms in the time domain (leaving out any manually created
marks). These automatic marks are created using a search
command. The entries returned are in the form of an enumeration
representing the source waveform, followed by 7 time mark
parameters.
SEARCH:SEARCH<x>:STATE Sets the search state to on or off
SEARCH:SEARCH<x>:TOTal? Returns the total number of matches for search <x>
SEARCH:SEARCH<x>:TRIGger:A:BUS? Queries the SEARCH:SE ARCH<x>:TRIGger:A:BUS settings.
2-62 MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual
Command Groups
Table 2-39: Search Commands (cont.)
Command Description
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ARINC429A:
CONDition
This command sets the condition to use w hen searching on
ARINC429 bus data (word start, label, matching data, word end, or
error).
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ARINC429A:
DATA:HIVALue
This command specifies the high value to use w hen searching on
the ARINC429 bus data field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ARINC429A:
DATA:QUALifier
This command sets the qualifier (<, >, =, <=, >=, not =, in range, out
of range) to use when searching on ARINC429 bus data field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ARINC429A:
DATA:VA Lue
This command specifies the low value to use when searching on
the ARINC429 bus data field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ARINC429A:
ERRTYPE
This command specifies the error type to use when searching on
the ARINC429 bus signal.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ARINC429A:
LABel:HIVALue
This command specifies the high value to use when searching on
the ARINC429 bus label field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ARINC429A:
LABel:QUALifier
This command sets the qualifier (<, >, =, <=, >=, not =, in range, out
of range) to use when searching on ARINC429 bus label field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ARINC429A:
LABel:VALue
This command specifies the low value to use when searching on
the ARINC429 bus label field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ARINC429A:
SDI
This command specifies the SDI portion of the packet data to be
used when searching on ARINC429 bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ARINC429A:
SSM
This command specifies the SSM portion of the packet data to be
used when searching on ARINC429 bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:AUDio:
CONDition
This command sets the condition (start of frame or matching data)
to be used to search on audio bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:AUDio:DATa:
HIVALue
This command sets the upper word value to be used to search on
audio bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:AUDio:DATa:
OFFSet
This commands sets the data offset v alue to be used to search
on audio bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:AUDio:DATa:
QUALifier
This command sets the qualifier (<, >, =, <=, >=, not =, in range, out
of range) to be used to search on audio bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:AUDio:DATa:
VALue
This command sets the lower word value to be used to search on
audio bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:AUDio:DATa:
WORD
This command sets the alignment of the data (left, right or either) to
be used to search on audio bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:CAN:
CONDition
This command sets the condition (start of frame, frame type,
identifier, matching data, end of frame, missing ACK field, bit-stuffing
error, form error, any error, CAN FD B RS bit, or CAN FD ESI bit) to
be used to search on CAN bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:CAN:DATa:
DIRection
This command sets the data direction (read, write or either) to be
used to search on CAN bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CAN:DATa:
OFFSet
This command specifies the data offset for CAN data searches.
MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual 2-63
Command Groups
Table 2-39: Search Commands (cont.)
Command Description
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CA N:DATa:
QUALifier
This command sets the quali fier (<, >, =, not =, <=) to be used to
search on CAN bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CA N:DATa:
SIZe
This command sets the length of the data string, in bytes, to be
used to search on CAN bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CA N:DATa:
VALue
This command sets the binary data value to be used to search on
CAN bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CA N:FD:
BRSBIT
This command sets the value (don’t care, 1, or 0) to be used to
search for CAN FD BRS bits.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CA N:FD:
ESIBIT
This command sets the value (don’t care, 1, or 0) to be used to
search for CAN FD ESI bits.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CA N:
FRAMEtype
This command sets the frame type (data, remote, error or overload)
to be used to search on CAN bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CA N{:
IDentifier|:ADDRess}:MODe
This command sets the addressing mode (standard or extended
format) to be used to search on CAN bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CA N{:
IDentifier|:ADDRess}:VALue
This command sets the binary address value to be used to search
on CAN bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ETHERn et:
CONDition
When searching through Ethernet data, this command specifies the
field or condition to search on.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ETHERn et:
DATa:HIVALue
When the search condition is set to DATa, and the qualifier is set
to either
INrange or OUTrange, this command specifies the
upper data value of the range.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ETHERn et:
DATa:OFFSet
When the search condition is set to DATa, this command specifies
where in the data field to look for the data search value.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ETHERn et:
DATa:SIZe
When the search condition is set to DATa, this command specifies
the number of contiguous TCP/IPv4/MAC client data bytes to
search for.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ETHERn et:
DATa:VALue
When the search condition is set to DATa, and the qualifier is set to
LESSthan, MOREthan, EQual, UNEQual, LESSEQual
or MOREEQual, this command specifies the value to search on.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ETHERn et:
FRAMETYPe
This command specifies which Ethernet frame type to search on:
either Basic or QTAG (IEEE 802.1Q , or VLAN tagging).
SEARCH:SEARC H<x >:T R IG:A:BU S:B<x>:ET H ER:IPH:
DEST:VAL
When the Ethernet search condition is set to
IPHeader,this
command specifies the value of the 32–bit destination address that
is to be used in the search (along with the protocol and source
address).
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ETHERn et:
IPHeader:PROTOcol:VALue
When the Ethernet search condition is set to
IPHeader,this
command specifies the value of the 8–bit protocol field that is
to be used in the search (along with the source and destination
addresses).
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ETHERn et:
IPHeader:SOUrceaddr:VALue
When the Ethernet search condition is set to
IPHeader,this
command specifies the value of the 32–bit source address that
will be used in the search (along with the protocol and destination
address).
2-64 MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual