MDO3000 Programmer Manual.pdf - 第94页

Command Groups T able 2-39: Search Commands (cont.) Command Description SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CA N:DA T a: QUALi fi er This command sets the quali fi er (<, >, =, not =, <=) to be used to…

100%1 / 1158
Command Groups
Table 2-39: Search Commands (cont.)
Command Description
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ARINC429A:
CONDition
This command sets the condition to use w hen searching on
ARINC429 bus data (word start, label, matching data, word end, or
error).
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ARINC429A:
DATA:HIVALue
This command specifies the high value to use w hen searching on
the ARINC429 bus data field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ARINC429A:
DATA:QUALifier
This command sets the qualifier (<, >, =, <=, >=, not =, in range, out
of range) to use when searching on ARINC429 bus data field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ARINC429A:
DATA:VA Lue
This command specifies the low value to use when searching on
the ARINC429 bus data field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ARINC429A:
ERRTYPE
This command specifies the error type to use when searching on
the ARINC429 bus signal.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ARINC429A:
LABel:HIVALue
This command specifies the high value to use when searching on
the ARINC429 bus label field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ARINC429A:
LABel:QUALifier
This command sets the qualifier (<, >, =, <=, >=, not =, in range, out
of range) to use when searching on ARINC429 bus label field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ARINC429A:
LABel:VALue
This command specifies the low value to use when searching on
the ARINC429 bus label field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ARINC429A:
SDI
This command specifies the SDI portion of the packet data to be
used when searching on ARINC429 bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ARINC429A:
SSM
This command specifies the SSM portion of the packet data to be
used when searching on ARINC429 bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:AUDio:
CONDition
This command sets the condition (start of frame or matching data)
to be used to search on audio bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:AUDio:DATa:
HIVALue
This command sets the upper word value to be used to search on
audio bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:AUDio:DATa:
OFFSet
This commands sets the data offset v alue to be used to search
on audio bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:AUDio:DATa:
QUALifier
This command sets the qualifier (<, >, =, <=, >=, not =, in range, out
of range) to be used to search on audio bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:AUDio:DATa:
VALue
This command sets the lower word value to be used to search on
audio bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:AUDio:DATa:
WORD
This command sets the alignment of the data (left, right or either) to
be used to search on audio bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:CAN:
CONDition
This command sets the condition (start of frame, frame type,
identifier, matching data, end of frame, missing ACK field, bit-stuffing
error, form error, any error, CAN FD B RS bit, or CAN FD ESI bit) to
be used to search on CAN bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:CAN:DATa:
DIRection
This command sets the data direction (read, write or either) to be
used to search on CAN bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CAN:DATa:
OFFSet
This command specifies the data offset for CAN data searches.
MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual 2-63
Command Groups
Table 2-39: Search Commands (cont.)
Command Description
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CA N:DATa:
QUALifier
This command sets the quali fier (<, >, =, not =, <=) to be used to
search on CAN bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CA N:DATa:
SIZe
This command sets the length of the data string, in bytes, to be
used to search on CAN bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CA N:DATa:
VALue
This command sets the binary data value to be used to search on
CAN bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CA N:FD:
BRSBIT
This command sets the value (don’t care, 1, or 0) to be used to
search for CAN FD BRS bits.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CA N:FD:
ESIBIT
This command sets the value (don’t care, 1, or 0) to be used to
search for CAN FD ESI bits.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CA N:
FRAMEtype
This command sets the frame type (data, remote, error or overload)
to be used to search on CAN bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CA N{:
IDentifier|:ADDRess}:MODe
This command sets the addressing mode (standard or extended
format) to be used to search on CAN bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CA N{:
IDentifier|:ADDRess}:VALue
This command sets the binary address value to be used to search
on CAN bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ETHERn et:
CONDition
When searching through Ethernet data, this command specifies the
field or condition to search on.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ETHERn et:
DATa:HIVALue
When the search condition is set to DATa, and the qualifier is set
to either
INrange or OUTrange, this command specifies the
upper data value of the range.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ETHERn et:
DATa:OFFSet
When the search condition is set to DATa, this command specifies
where in the data field to look for the data search value.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ETHERn et:
DATa:SIZe
When the search condition is set to DATa, this command specifies
the number of contiguous TCP/IPv4/MAC client data bytes to
search for.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ETHERn et:
DATa:VALue
When the search condition is set to DATa, and the qualifier is set to
LESSthan, MOREthan, EQual, UNEQual, LESSEQual
or MOREEQual, this command specifies the value to search on.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ETHERn et:
FRAMETYPe
This command specifies which Ethernet frame type to search on:
either Basic or QTAG (IEEE 802.1Q , or VLAN tagging).
SEARCH:SEARC H<x >:T R IG:A:BU S:B<x>:ET H ER:IPH:
DEST:VAL
When the Ethernet search condition is set to
IPHeader,this
command specifies the value of the 32–bit destination address that
is to be used in the search (along with the protocol and source
address).
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ETHERn et:
IPHeader:PROTOcol:VALue
When the Ethernet search condition is set to
IPHeader,this
command specifies the value of the 8–bit protocol field that is
to be used in the search (along with the source and destination
addresses).
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ETHERn et:
IPHeader:SOUrceaddr:VALue
When the Ethernet search condition is set to
IPHeader,this
command specifies the value of the 32–bit source address that
will be used in the search (along with the protocol and destination
address).
2-64 MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual
Command Groups
Table 2-39: Search Commands (cont.)
Command Description
SEARCH:SEARCH<x>:TRIG:A:BUS:B<x>:ETHER:MAC:
ADDR:DEST:VAL
When the Ethernet search condition is set to
MACADDress ,this
command specifies the 48–bit MAC destination address v alue that
is to be used in the search (along with the source address value).
SEARCH:SEARCH<x>:TRIG:A:BUS:B<x>:ETHER:MAC:
ADDR:SOU:VAL
When the Ethernet search condition is set to
MACADDress ,this
command specifies the 48–bit M AC source address value that is to
be used in the search (along with the destination address value).
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:ETHERnet:
MAC{:LENgth|:TYPe}:?HIVALue
When the Ethernet search condition is set to
MACLENgth, and the
qualifier is set to either
INrange or OUTrange, this command
specifies the upper data value of this range.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:ETHERnet:
MAC{:LENgth|:TYPe}:VALue
When the Ethernet search condition is set to
MACLENgth,and
the qualifier is set to
LESSthan, MOREthan, EQual,
UNEQual, LESSEQual
or M OREEQual, this command
specifies the 16–bit value to search for.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:ETHERnet:
QTAG:VALue
When the Ethernet search condition is set to
QTAG, this command
specifies the 32–bit QTAG value to search for.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:ETHERnet:
QUALifier
This command speci fies the qualifier to be used when the Ethernet
search condition is set to
MACLENgth or DATa.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:ETHERnet:
TCPHeader:ACKnum:VALue
When the Ethernet search condition is set to
TCPHeader,this
command specifies the 32–bit acknowledgement value that is to
be used in the search (along with the destination and source port
addresses and the sequence number). The default is all X’s (don’t
care).
SEARCH:SEARCH<x>:TRIG:A:BUS:B<x>:ETHER:TCPH:
DEST:VAL
When the Ethernet search condition is set to
TCPHeader,this
command specifies the 16–bit destination port address that is to be
used in the search (along with the acknowledgement value, source
port address and the sequence number).
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:ETHERnet:
TCPHeader:SEQnum:VALue
When the Ethernet search condition is set to
TCPHEADER,this
command specifies the 32–bit sequence number that is to be used
in the search (along with the destination and source port addresses
and the acknowledgement value).
SEARCH:SEARCH<x>:TRIG:A:BUS:B<x>:ETHER:TCPH:
SOU:VAL
When the Ethernet search condition is set to
TCPHEADER,this
command specifies the 16–bit source port address that is to be
used in the search (along with the destination port address, the
sequence number and the acknowledgement number).
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEXray:
CONDition
This command specifies the condition to use when searching on
FlexRay bus data (start of frame, frame type, ID, cycle count,
header, data, ID and data, EO F, error).
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEXray:
CYCLEcount:HIVALue
This command specifies the upper data value of the range to be
used when searching on the FlexRay bus cycle count field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEXray:
CYCLEcount:QUALifier
This command speci fies the qualifier (<, >, =, <=, >=, not =, in
range, out of range) to use when searching on the FlexRay bus
cycle count field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEXray:
CYCLEcount:VALue
This command specifies the low data value to be used when
searching on the FlexRay bus cycle count field.
MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual 2-65