MDO3000 Programmer Manual.pdf - 第95页
Command Groups T able 2-39: Search Commands (cont.) Command Description SEARCH:SEARCH<x>:TR IG:A:BUS:B<x>: ETHER:MAC: ADDR:DEST :V AL When the Ethernet search condition is set to MACADDress ,t h i s command s…
Command Groups
Table 2-39: Search Commands (cont.)
Command Description
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CA N:DATa:
QUALifier
This command sets the quali fier (<, >, =, not =, <=) to be used to
search on CAN bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CA N:DATa:
SIZe
This command sets the length of the data string, in bytes, to be
used to search on CAN bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CA N:DATa:
VALue
This command sets the binary data value to be used to search on
CAN bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CA N:FD:
BRSBIT
This command sets the value (don’t care, 1, or 0) to be used to
search for CAN FD BRS bits.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CA N:FD:
ESIBIT
This command sets the value (don’t care, 1, or 0) to be used to
search for CAN FD ESI bits.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CA N:
FRAMEtype
This command sets the frame type (data, remote, error or overload)
to be used to search on CAN bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CA N{:
IDentifier|:ADDRess}:MODe
This command sets the addressing mode (standard or extended
format) to be used to search on CAN bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CA N{:
IDentifier|:ADDRess}:VALue
This command sets the binary address value to be used to search
on CAN bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ETHERn et:
CONDition
When searching through Ethernet data, this command specifies the
field or condition to search on.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ETHERn et:
DATa:HIVALue
When the search condition is set to DATa, and the qualifier is set
to either
INrange or OUTrange, this command specifies the
upper data value of the range.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ETHERn et:
DATa:OFFSet
When the search condition is set to DATa, this command specifies
where in the data field to look for the data search value.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ETHERn et:
DATa:SIZe
When the search condition is set to DATa, this command specifies
the number of contiguous TCP/IPv4/MAC client data bytes to
search for.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ETHERn et:
DATa:VALue
When the search condition is set to DATa, and the qualifier is set to
LESSthan, MOREthan, EQual, UNEQual, LESSEQual
or MOREEQual, this command specifies the value to search on.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ETHERn et:
FRAMETYPe
This command specifies which Ethernet frame type to search on:
either Basic or QTAG (IEEE 802.1Q , or VLAN tagging).
SEARCH:SEARC H<x >:T R IG:A:BU S:B<x>:ET H ER:IPH:
DEST:VAL
When the Ethernet search condition is set to
IPHeader,this
command specifies the value of the 32–bit destination address that
is to be used in the search (along with the protocol and source
address).
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ETHERn et:
IPHeader:PROTOcol:VALue
When the Ethernet search condition is set to
IPHeader,this
command specifies the value of the 8–bit protocol field that is
to be used in the search (along with the source and destination
addresses).
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:ETHERn et:
IPHeader:SOUrceaddr:VALue
When the Ethernet search condition is set to
IPHeader,this
command specifies the value of the 32–bit source address that
will be used in the search (along with the protocol and destination
address).
2-64 MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual
Command Groups
Table 2-39: Search Commands (cont.)
Command Description
SEARCH:SEARCH<x>:TRIG:A:BUS:B<x>:ETHER:MAC:
ADDR:DEST:VAL
When the Ethernet search condition is set to
MACADDress ,this
command specifies the 48–bit MAC destination address v alue that
is to be used in the search (along with the source address value).
SEARCH:SEARCH<x>:TRIG:A:BUS:B<x>:ETHER:MAC:
ADDR:SOU:VAL
When the Ethernet search condition is set to
MACADDress ,this
command specifies the 48–bit M AC source address value that is to
be used in the search (along with the destination address value).
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:ETHERnet:
MAC{:LENgth|:TYPe}:?HIVALue
When the Ethernet search condition is set to
MACLENgth, and the
qualifier is set to either
INrange or OUTrange, this command
specifies the upper data value of this range.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:ETHERnet:
MAC{:LENgth|:TYPe}:VALue
When the Ethernet search condition is set to
MACLENgth,and
the qualifier is set to
LESSthan, MOREthan, EQual,
UNEQual, LESSEQual
or M OREEQual, this command
specifies the 16–bit value to search for.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:ETHERnet:
QTAG:VALue
When the Ethernet search condition is set to
QTAG, this command
specifies the 32–bit QTAG value to search for.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:ETHERnet:
QUALifier
This command speci fies the qualifier to be used when the Ethernet
search condition is set to
MACLENgth or DATa.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:ETHERnet:
TCPHeader:ACKnum:VALue
When the Ethernet search condition is set to
TCPHeader,this
command specifies the 32–bit acknowledgement value that is to
be used in the search (along with the destination and source port
addresses and the sequence number). The default is all X’s (don’t
care).
SEARCH:SEARCH<x>:TRIG:A:BUS:B<x>:ETHER:TCPH:
DEST:VAL
When the Ethernet search condition is set to
TCPHeader,this
command specifies the 16–bit destination port address that is to be
used in the search (along with the acknowledgement value, source
port address and the sequence number).
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:ETHERnet:
TCPHeader:SEQnum:VALue
When the Ethernet search condition is set to
TCPHEADER,this
command specifies the 32–bit sequence number that is to be used
in the search (along with the destination and source port addresses
and the acknowledgement value).
SEARCH:SEARCH<x>:TRIG:A:BUS:B<x>:ETHER:TCPH:
SOU:VAL
When the Ethernet search condition is set to
TCPHEADER,this
command specifies the 16–bit source port address that is to be
used in the search (along with the destination port address, the
sequence number and the acknowledgement number).
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEXray:
CONDition
This command specifies the condition to use when searching on
FlexRay bus data (start of frame, frame type, ID, cycle count,
header, data, ID and data, EO F, error).
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEXray:
CYCLEcount:HIVALue
This command specifies the upper data value of the range to be
used when searching on the FlexRay bus cycle count field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEXray:
CYCLEcount:QUALifier
This command speci fies the qualifier (<, >, =, <=, >=, not =, in
range, out of range) to use when searching on the FlexRay bus
cycle count field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEXray:
CYCLEcount:VALue
This command specifies the low data value to be used when
searching on the FlexRay bus cycle count field.
MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual 2-65
Command Groups
Table 2-39: Search Commands (cont.)
Command Description
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
DATa:HIVALue
This command specifi es the high value to use when searching on
the FlexRay bus data field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
DATa:OFFSet
This command speci fies the offset of the data string in bytes to be
used when searching on the FlexRay bus data field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
DATa:QUALifier
This command specifies the qualifier (<, >, = , <=, >=, not =, in range,
out of range) to use when searching on the FlexRay bus data field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
DATa:SIZe
This command specifies the length of the data string, in bytes, to
use when searching on the FlexRay bus data field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
DATa:VALue
This command specifies the low value to use when searching on
the FlexRay bus data field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
EOFTYPE
This command specifies which end of file type to use (static,
dynamic or any) when searching on the FlexRay bus EOF field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
ERRTYPE
This command specifies the error type to use when searching on
the FlexRay bus signal.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
FRAMEID:HIVALue
This command specifies the high value to use when searching on
the FlexRay bus frame ID field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
FRAMEID:QUALifier
This command specifies the qualifier to use when searching on
the FlexRay bus frame ID field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
FRAMEID:VALue
This command specifies the low value to use when searching on
the FlexRay bus frame ID field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
FRAMEType
This command specifies the frame type (normal, payload, null, sync
or startup) to use when searching on FlexRay bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
HEADER:CRC
This command specifies the CRC portion of the binary header string
to be used when searching on FlexRay bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
HEADER:CYCLEcount
This command specifies to use the cycle count portion of the binary
header string when searching on the FlexRay bus header.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
HEADER:FRAMEID
This command specifies to use the frame ID portion of the binary
header string when searching on the FlexRay bus header.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
HEADER:INDBits
This command specifies to use the indicator bits portion of the
binary header string when searching on the FlexRay bus header.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
HEADER:PAYLength
This command specifies to use the payload length portion of the
binary header string when searching on the FlexRay bus header.
SEARCH:SEARC H<x >:T R IGger:A:BUS:B<x>:I2C:ADDRe ss:
MODe
This command specifies the I2C address mode to 7 or 10-Bit
SEARCH:SEARC H<x >:T R IGger:A:BUS:B<x>:I2C:ADDRe ss:
TYPe
This command specifies the I2C address type to I2C special
addresses
SEARCH:SEARC H<x >:T R IGger:A:BUS:B<x>:I2C:ADDRe ss:
VALue
This command specifies the binary address string to be used for
I2C search
SEARCH:SEARC H<x >:T R IGger:A:BUS:B<x>:I2C:CONDition This command specifies the search condition for I2C search
SEARCH:SEARC H<x >:T R IGger:A:BUS:B<x>:I2C:DATa:
DIRection
This command specifies the I2C search condition to be valid on a
READ, WRITE or either
2-66 MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual