MDO3000 Programmer Manual.pdf - 第96页
Command Groups T able 2-39: Search Commands (cont.) Command Description SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray: DA T a:HIV ALue This command speci fi es the high value to use when searching on the FlexRa…
Command Groups
Table 2-39: Search Commands (cont.)
Command Description
SEARCH:SEARCH<x>:TRIG:A:BUS:B<x>:ETHER:MAC:
ADDR:DEST:VAL
When the Ethernet search condition is set to
MACADDress ,this
command specifies the 48–bit MAC destination address v alue that
is to be used in the search (along with the source address value).
SEARCH:SEARCH<x>:TRIG:A:BUS:B<x>:ETHER:MAC:
ADDR:SOU:VAL
When the Ethernet search condition is set to
MACADDress ,this
command specifies the 48–bit M AC source address value that is to
be used in the search (along with the destination address value).
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:ETHERnet:
MAC{:LENgth|:TYPe}:?HIVALue
When the Ethernet search condition is set to
MACLENgth, and the
qualifier is set to either
INrange or OUTrange, this command
specifies the upper data value of this range.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:ETHERnet:
MAC{:LENgth|:TYPe}:VALue
When the Ethernet search condition is set to
MACLENgth,and
the qualifier is set to
LESSthan, MOREthan, EQual,
UNEQual, LESSEQual
or M OREEQual, this command
specifies the 16–bit value to search for.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:ETHERnet:
QTAG:VALue
When the Ethernet search condition is set to
QTAG, this command
specifies the 32–bit QTAG value to search for.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:ETHERnet:
QUALifier
This command speci fies the qualifier to be used when the Ethernet
search condition is set to
MACLENgth or DATa.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:ETHERnet:
TCPHeader:ACKnum:VALue
When the Ethernet search condition is set to
TCPHeader,this
command specifies the 32–bit acknowledgement value that is to
be used in the search (along with the destination and source port
addresses and the sequence number). The default is all X’s (don’t
care).
SEARCH:SEARCH<x>:TRIG:A:BUS:B<x>:ETHER:TCPH:
DEST:VAL
When the Ethernet search condition is set to
TCPHeader,this
command specifies the 16–bit destination port address that is to be
used in the search (along with the acknowledgement value, source
port address and the sequence number).
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:ETHERnet:
TCPHeader:SEQnum:VALue
When the Ethernet search condition is set to
TCPHEADER,this
command specifies the 32–bit sequence number that is to be used
in the search (along with the destination and source port addresses
and the acknowledgement value).
SEARCH:SEARCH<x>:TRIG:A:BUS:B<x>:ETHER:TCPH:
SOU:VAL
When the Ethernet search condition is set to
TCPHEADER,this
command specifies the 16–bit source port address that is to be
used in the search (along with the destination port address, the
sequence number and the acknowledgement number).
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEXray:
CONDition
This command specifies the condition to use when searching on
FlexRay bus data (start of frame, frame type, ID, cycle count,
header, data, ID and data, EO F, error).
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEXray:
CYCLEcount:HIVALue
This command specifies the upper data value of the range to be
used when searching on the FlexRay bus cycle count field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEXray:
CYCLEcount:QUALifier
This command speci fies the qualifier (<, >, =, <=, >=, not =, in
range, out of range) to use when searching on the FlexRay bus
cycle count field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEXray:
CYCLEcount:VALue
This command specifies the low data value to be used when
searching on the FlexRay bus cycle count field.
MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual 2-65
Command Groups
Table 2-39: Search Commands (cont.)
Command Description
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
DATa:HIVALue
This command specifi es the high value to use when searching on
the FlexRay bus data field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
DATa:OFFSet
This command speci fies the offset of the data string in bytes to be
used when searching on the FlexRay bus data field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
DATa:QUALifier
This command specifies the qualifier (<, >, = , <=, >=, not =, in range,
out of range) to use when searching on the FlexRay bus data field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
DATa:SIZe
This command specifies the length of the data string, in bytes, to
use when searching on the FlexRay bus data field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
DATa:VALue
This command specifies the low value to use when searching on
the FlexRay bus data field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
EOFTYPE
This command specifies which end of file type to use (static,
dynamic or any) when searching on the FlexRay bus EOF field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
ERRTYPE
This command specifies the error type to use when searching on
the FlexRay bus signal.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
FRAMEID:HIVALue
This command specifies the high value to use when searching on
the FlexRay bus frame ID field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
FRAMEID:QUALifier
This command specifies the qualifier to use when searching on
the FlexRay bus frame ID field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
FRAMEID:VALue
This command specifies the low value to use when searching on
the FlexRay bus frame ID field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
FRAMEType
This command specifies the frame type (normal, payload, null, sync
or startup) to use when searching on FlexRay bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
HEADER:CRC
This command specifies the CRC portion of the binary header string
to be used when searching on FlexRay bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
HEADER:CYCLEcount
This command specifies to use the cycle count portion of the binary
header string when searching on the FlexRay bus header.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
HEADER:FRAMEID
This command specifies to use the frame ID portion of the binary
header string when searching on the FlexRay bus header.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
HEADER:INDBits
This command specifies to use the indicator bits portion of the
binary header string when searching on the FlexRay bus header.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
HEADER:PAYLength
This command specifies to use the payload length portion of the
binary header string when searching on the FlexRay bus header.
SEARCH:SEARC H<x >:T R IGger:A:BUS:B<x>:I2C:ADDRe ss:
MODe
This command specifies the I2C address mode to 7 or 10-Bit
SEARCH:SEARC H<x >:T R IGger:A:BUS:B<x>:I2C:ADDRe ss:
TYPe
This command specifies the I2C address type to I2C special
addresses
SEARCH:SEARC H<x >:T R IGger:A:BUS:B<x>:I2C:ADDRe ss:
VALue
This command specifies the binary address string to be used for
I2C search
SEARCH:SEARC H<x >:T R IGger:A:BUS:B<x>:I2C:CONDition This command specifies the search condition for I2C search
SEARCH:SEARC H<x >:T R IGger:A:BUS:B<x>:I2C:DATa:
DIRection
This command specifies the I2C search condition to be valid on a
READ, WRITE or either
2-66 MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual
Command Groups
Table 2-39: Search Commands (cont.)
Command Description
SEARCH:SEARC H<x>:T RIG ger:A:BUS:B<x>:I2C:DATa:SIZe This command specifies the length of the data string in bytes to
be used for I2C search
SEARCH:SEARC H<x>:T RIG ger:A:BUS:B<x>:I2C:DATa:
VALue
This command specifiesthebinarydatastringtobeusedforI2C
search
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:LIN:CONDition This command specifies the search condition for a LIN search
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:LIN:DATa:
HIVALue
This command specifies the binary data string
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:LIN:DATa:
QUALifier
This command specifies the LIN data qualifier
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:LIN:DATa:SIZe This command specifies the length of the data string in bytes
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:LIN:DATa:
VALue
This command specifies the binary data string used for a LIN search
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:LIN:ERRTYPE This command specifies the error type used for a LIN search
SEARCH:SEARC H<x>:T RIG ger:A:BUS:B<x>:LIN:IDentifier:
VALue
This command specifi es the binary address string used for LIN
search
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:MIL1553B :
COMMAND:ADDRess:HIVALue
When the MIL-STD-1553 bus search condition is set to COMMAND,
and the qualifier is set to
INrange or OUTrange , this command
specifies the upper limit of the range for the remote terminal
address field.
SEARCH:SEARCH<x>:TRIG:A:BUS:B<x>:MIL1553B:
COMMAND:ADDR:QUAL
When the MIL-STD-1553 bus search condition is set to COMMAND,
this command specifies the qualifier to be used with the remote
terminal address field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:MIL1553B :
COMMAND:ADDRess:VALue
When the MIL-STD-1553 bus search condition is set to COMMAND,
and the qualifier is set to
LESSthan, MOREthan, EQual,
UNEQual, LESSEQual
or MOREEQual, this command
specifies the value of the 5–bit r emote terminal address to be used
in the search.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:MIL1553B :
COMMAND:COUNt
When the MIL-STD-1553 bus search condition is set to COMMAND,
this command speci fies the bit pattern for the 5–bit Word
Count/Mode Code sub-address field that is to be used in the search.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:MIL1553B :
COMMAND:PARity
When the MIL-STD-1553 bus search condition is set to COMMAND,
this command specifies the Command word parity that is to be used
in the search.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:MIL1553B :
COMMAND:SUBADdress
When the MIL-STD-1553 bus search condition is set to COMMAND,
this command specifies the 5 bit sub-address that is to be used
in the search.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:MIL1553B :
COMMAND:TRBit
When the MIL-STD-1553 bus search condition is set to COMMAND,
this command specifies that the transmit/receive bit ( bit 9) is to be
used in the search.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:MIL1553B :
CONDition
This command specifies a word type or condition within a
MIL-STD-1553 bus word to search for.
SEARCH<x> is the search
number, which is always 1, and
B<x>
MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual 2-67