MDO3000 Programmer Manual.pdf - 第97页

Command Groups T able 2-39: Search Commands (cont.) Command Description SEARCH:SEARC H<x>:T RIG ger:A:B US:B<x>:I2C:DA T a:SIZe This command speci fi es the length of the data string in bytes to be used for I2…

100%1 / 1158
Command Groups
Table 2-39: Search Commands (cont.)
Command Description
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
DATa:HIVALue
This command specifi es the high value to use when searching on
the FlexRay bus data field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
DATa:OFFSet
This command speci fies the offset of the data string in bytes to be
used when searching on the FlexRay bus data field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
DATa:QUALifier
This command specifies the qualifier (<, >, = , <=, >=, not =, in range,
out of range) to use when searching on the FlexRay bus data field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
DATa:SIZe
This command specifies the length of the data string, in bytes, to
use when searching on the FlexRay bus data field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
DATa:VALue
This command specifies the low value to use when searching on
the FlexRay bus data field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
EOFTYPE
This command specifies which end of file type to use (static,
dynamic or any) when searching on the FlexRay bus EOF field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
ERRTYPE
This command specifies the error type to use when searching on
the FlexRay bus signal.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
FRAMEID:HIVALue
This command specifies the high value to use when searching on
the FlexRay bus frame ID field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
FRAMEID:QUALifier
This command specifies the qualifier to use when searching on
the FlexRay bus frame ID field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
FRAMEID:VALue
This command specifies the low value to use when searching on
the FlexRay bus frame ID field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
FRAMEType
This command specifies the frame type (normal, payload, null, sync
or startup) to use when searching on FlexRay bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
HEADER:CRC
This command specifies the CRC portion of the binary header string
to be used when searching on FlexRay bus data.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
HEADER:CYCLEcount
This command specifies to use the cycle count portion of the binary
header string when searching on the FlexRay bus header.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
HEADER:FRAMEID
This command specifies to use the frame ID portion of the binary
header string when searching on the FlexRay bus header.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
HEADER:INDBits
This command specifies to use the indicator bits portion of the
binary header string when searching on the FlexRay bus header.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:FLEX ray:
HEADER:PAYLength
This command specifies to use the payload length portion of the
binary header string when searching on the FlexRay bus header.
SEARCH:SEARC H<x >:T R IGger:A:BUS:B<x>:I2C:ADDRe ss:
MODe
This command specifies the I2C address mode to 7 or 10-Bit
SEARCH:SEARC H<x >:T R IGger:A:BUS:B<x>:I2C:ADDRe ss:
TYPe
This command specifies the I2C address type to I2C special
addresses
SEARCH:SEARC H<x >:T R IGger:A:BUS:B<x>:I2C:ADDRe ss:
VALue
This command specifies the binary address string to be used for
I2C search
SEARCH:SEARC H<x >:T R IGger:A:BUS:B<x>:I2C:CONDition This command specifies the search condition for I2C search
SEARCH:SEARC H<x >:T R IGger:A:BUS:B<x>:I2C:DATa:
DIRection
This command specifies the I2C search condition to be valid on a
READ, WRITE or either
2-66 MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual
Command Groups
Table 2-39: Search Commands (cont.)
Command Description
SEARCH:SEARC H<x>:T RIG ger:A:BUS:B<x>:I2C:DATa:SIZe This command specifies the length of the data string in bytes to
be used for I2C search
SEARCH:SEARC H<x>:T RIG ger:A:BUS:B<x>:I2C:DATa:
VALue
This command specifiesthebinarydatastringtobeusedforI2C
search
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:LIN:CONDition This command specifies the search condition for a LIN search
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:LIN:DATa:
HIVALue
This command specifies the binary data string
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:LIN:DATa:
QUALifier
This command specifies the LIN data qualifier
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:LIN:DATa:SIZe This command specifies the length of the data string in bytes
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:LIN:DATa:
VALue
This command specifies the binary data string used for a LIN search
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:LIN:ERRTYPE This command specifies the error type used for a LIN search
SEARCH:SEARC H<x>:T RIG ger:A:BUS:B<x>:LIN:IDentifier:
VALue
This command specifi es the binary address string used for LIN
search
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:MIL1553B :
COMMAND:ADDRess:HIVALue
When the MIL-STD-1553 bus search condition is set to COMMAND,
and the qualifier is set to
INrange or OUTrange , this command
specifies the upper limit of the range for the remote terminal
address field.
SEARCH:SEARCH<x>:TRIG:A:BUS:B<x>:MIL1553B:
COMMAND:ADDR:QUAL
When the MIL-STD-1553 bus search condition is set to COMMAND,
this command specifies the qualifier to be used with the remote
terminal address field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:MIL1553B :
COMMAND:ADDRess:VALue
When the MIL-STD-1553 bus search condition is set to COMMAND,
and the qualifier is set to
LESSthan, MOREthan, EQual,
UNEQual, LESSEQual
or MOREEQual, this command
specifies the value of the 5–bit r emote terminal address to be used
in the search.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:MIL1553B :
COMMAND:COUNt
When the MIL-STD-1553 bus search condition is set to COMMAND,
this command speci fies the bit pattern for the 5–bit Word
Count/Mode Code sub-address field that is to be used in the search.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:MIL1553B :
COMMAND:PARity
When the MIL-STD-1553 bus search condition is set to COMMAND,
this command specifies the Command word parity that is to be used
in the search.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:MIL1553B :
COMMAND:SUBADdress
When the MIL-STD-1553 bus search condition is set to COMMAND,
this command specifies the 5 bit sub-address that is to be used
in the search.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:MIL1553B :
COMMAND:TRBit
When the MIL-STD-1553 bus search condition is set to COMMAND,
this command specifies that the transmit/receive bit ( bit 9) is to be
used in the search.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B <x>:MIL1553B :
CONDition
This command specifies a word type or condition within a
MIL-STD-1553 bus word to search for.
SEARCH<x> is the search
number, which is always 1, and
B<x>
MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual 2-67
Command Groups
Table 2-39: Search Commands (cont.)
Command Description
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:MIL1553B:
DATa:PARity
When the MIL-STD-1553 bus search condition is set to DATa,this
command specifies the data parity bit to be used in the search.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:MIL1553B:
DATa:VALue
When the MIL-STD-1553 bus search condition is set to DATa,this
command specifies the data binary pattern to be used in the search.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:MIL1553B:
ERRTYPE
When the MIL-STD-1553 bus search condition is set to ERRor,
this command specifies the signaling error type to be used in the
search: Parity, Sync, Manchester or D ata.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:MIL1553B:
STATus:ADDRess:HIVALue
When the MIL-STD-1553 bus search condition is set to STATus,
and the qualifi er is set to
INrange or OUTrange, this command
specifies the upper limit for the 5 bit remote terminal address field
of the Status word.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:MIL1553B:
STATus:ADDRess:VALue
When the MIL-STD-1553 bus search condition is set to STATus,
and the qualifier is set to
LESSthan, MOREthan, EQual,
UNEQual, LESSEQual
or MOREEQual, this command
specifies the value of the 5–bit r emote terminal address to be used
in the search.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:MIL1553B:
STATus:ADDRess:QUALifier
When the MIL-STD-1553 bus search condition is set to STATus,
this command specifies the qualifier to be used with the address
field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:MIL1553B:
STATus:BIT:BCR
When the MIL-STD-1553 bus search condition is set to STATus,
this command specifies the s tatus word broadcast command
received (BCR) bit value (bit 15) to be used in the search.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:MIL1553B:
STATus:BIT:BUSY
When the MIL-STD-1553 bus search condition is set to STATus,
this command specifies the status word busy bit value (bit 16) to be
used in the search.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:MIL1553B:
STATus:BIT:DBCA
When the MIL-STD-1553 bus search condition is set to STATus,
this command specifies the s tatus word dynamic bus control
acceptance (DBCA) bit value (bit 18) to be used in the search.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:MIL1553B:
STATus :BIT:INSTR
When the MIL-STD-1553 bus search condition is set to STATus,
this command specifies the status word instrumentation bit value
(bit 10) to be used in the search.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:MIL1553B:
STATus :BIT:ME
When the MIL-STD-1553 bus search condition is set to STATus,
this command specifies the status w ord m essage error bit value
(bit 9) to be used in the s earch.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:MIL1553B:
STATus:BIT:SRQ
When the MIL-STD-1553 bus search condition is set to STATus,
this command specifies the status word service request (SRQ) bit
value (bit 11) to be used in the search.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:MIL1553B:
STATus:BIT:SUBSF
When the MIL-STD-1553 bus search condition is set to STATus,
this command specifies the status word subsystem flag bit value
(bit 17) to be used in the search.
SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:MIL1553B:
STATus :BIT:TF
When theMIL-STD-1553 bus search condition is set to STATus,
this command specifies the status word terminal flag bit value (bit
19) to be used in the search.
2-68 MDO4000/B/C, MSO/DPO4000B and MDO3000 Series Oscilloscopes Programmer Manual