ELA Installation.pdf - 第16页
SAFETY FEA TURES HIGH VOLTAGE PROTEC TION 2.6 I nstallation M anual Chapter Issue 3 Jun 01 HIGH V OL T A GE PRO TECTION Mechanisms The machine incorporates Class 1 electrical protection accor ding to the IEC 536 requirem…
SAFETY FEATURES
FRAME COVERS
Chapter Issue 3 Jun 01 Installation Manual 2.5
FRAME COVERS
In order to protect personnel and prevent damage to the machine, six panels are
fitted around the base of the machine. These panels (listed below) may be
removed to assist maintenance.
• Front Panel
• Side Panels - Front (2 positions)
• Side Panels - Rear (2 positions)
• Rear Panel
Removal of the front and rear panels requires a maintenance key to release two
locking mechanisms located externally at the top corners of each panel (Panel
Locking Mechanism figure refers ).
The two side front panels on each side of the machine are slid forward of their
internal support lugs at the bottom of the machine, (providing that both the
individual internal quick release fasteners have been released).
The two side rear panels on each side of the machine are slid to the rear of their
internal support lugs at the bottom of the machine, (after the rear panel has been
removed) and their individual internal quick release fasteners (2 positions) have
been released.
Figure 2-2 Panel Locking Mechanism
Enclosures Enclosures are not fitted with a safety interlock. Inadvertent access to such
enclosures is prevented by the presence of the enclosure panels and the frame
covers. However within enclosures, care has been taken to ensure that electri-
cally live components are covered.
SAFETY FEATURES
HIGH VOLTAGE PROTECTION
2.6 Installation Manual Chapter Issue 3 Jun 01
HIGH VOLTAGE PROTECTION
Mechanisms The machine incorporates Class 1 electrical protection according to the IEC 536
requirement 1:1993.
All machines prior to shipment undergo electrical safety tests as described in
EN60204-1 (1997) Section 19:
• 19.2 Continuity of the protective bonding circuit
• 19.3 Insulation resistance test
With the exception of the optional Onboard Suction Filtration Unit, machine
mechanisms are powered by voltages less than 50V and do not pose an electrical
hazard to personnel.
NOTE
Refer to Chapter 5 Machine Preparation (Machine Relocation section) for
information on Vacuum Filtration Unit checks.
Access Where incoming supply voltages are present, protection is afforded by control-
ling access to the enclosures that house the supply. The machine is fitted with a
mains isolator switch that cuts power to all circuits located beyond the switch on
both in coming and out going power terminals. The isolator switch is located at
the front of the machine.
Hazard Warning
Labels
Hazard warning labels are placed on the outside of enclosures where dangerous
voltage (100V-240V) terminations are present within.
Earth Bonding All external metal surfaces are mechanically and electrically bonded to the
machine earth point. The bonding wire used is identified by its green and yellow
insulation and is commonly used to earth bond throughout. Care should be taken
when removing these links that when they are replaced they are secured tightly
and cleanly.
SERVICES REQUIRED
MACHINE EXTERNAL SERVICES
Chapter Issue 3 Jun 01 Installation Manual 3.1
CHAPTER 3 SERVICES REQUIRED
MACHINE EXTERNAL SERVICES
In order for the machine to function correctly the following services must be
available. The services must be stable and clean.
Figure 3-1 External Services
Item Description Item Description
1 6SK13 Host Comms LAN RJ45 5 Vacuum Connection
2 Mains Supply 6 24V Vacuum Control
3 Multi-Interface Unit 7 6SK09 Parallel Port Printer
4 Air Connection
+
2
4
V
+24V
+
2
4
V
(
E
-
S
T
O
P
)
+
24
V
(E
-
S
T
OP
)
+
1
2
V
+
1
2V
+
5
V
+5
V
D
O
W
N
L
I
N
E
R
E
A
D
Y
DOWNL
IN
E
REA
D
Y
RS2
3
2
R
S
2
3
2
D
OW
N
L
IN
E
D
OWN
L
IN
E
U
PL
IN
E
U
PL
IN
E
D
EKMA
CHI
N
E
D
EK
MA
C
H
I
N
E
U
P
L
I
N
E
R
E
A
D
Y
UP
L
INE
R
EADY
D
O
W
N
L
I
N
E
AVA
I
L
A
B
L
E
DOWNL
I
NEAVAI
LAB
L
E
S
E
N
D
D
O
W
N
L
I
N
E
SE
ND
DO
W
NLIN
E
S
E
N
D
U
P
L
I
N
E
SEND
U
PLI
NE
D
E
K
M
/
C
N
AVA
I
L
A
B
L
E
D
E
K
M/
CN
AVAI
LABLE
M
U
L
T
I
-
I
N
T
E
R
F
A
C
E
U
N
I
T
M
U
L
T
I
-IN
TE
RFACE
UN
I
T
F
R
O
M
D
E
K
M
A
C
H
I
N
E
FRO
M
DEK
M
A
C
H
INE
+24V
+24V (E-STOP)
+12V
+5V
DOWNLINE READY
RS 232
DOWNLINE
UPLINE
DEK MACHINE
UPLINE READY
DOWNLINE AVAILABLE
SEND DOWNLINE
SEND UPLINE
DEK M/CN AVAILABLE
MULTI-INTERFACE UNIT
FROM
DEK
MACHINE
1
3
4
2
7
5
View of Rear Left Side of Machine
6