ELA Installation.pdf - 第65页
FOREIGN MACHINE INTERFA CE PROCEDURE Chapter Issu e 3 Jun 01 Installati on Manua l 7.5 PR OCEDURE Ensure MIU is confi gured with the correct protocols for upline and downline machines as de tailed earlier . 1. Po wer up …
FOREIGN MACHINE INTERFACE
MULTI-INTERFACE UNIT
7.4 Installation Manual Chapter Issue 3 Jun 01
Card Access To gain access to the three selector switches proceed as follows:
1. Remove connections to the MIU.
2. Remove the MIU from the bracket by releasing the four screws.
3. Remove the six MIU back plate screws.
Part Numbers and Settings
NOTE
DEK do not supply Dynapert, Philips or Europlacer interface cables.
FMI Cables With the cables supplied, connect the upline and downline machines to the
screen printer MIU box connections. Cables should be routed down behind the
rear access panel.
Protocol
MIU Setting Cable Part Number
Upline SW2 Downline SW3 Upline Downline
Dynapert 0 0 N/A N/A
Philips 1 1 N/A N/A
SMEMA 2 2 131343 131345
Siemens 3 3 131335 131337
SMPI 4 4 131331 131333
TDK 5 5 131323 131325
Europlacer 6 6 N/A N/A
Fuji 7 7 126757 126758
Panasonic 7 7 131339 131341
Sanyo 8 8 146120 146119
Sanyo Flow Out 9 9 146120 146119
FOREIGN MACHINE INTERFACE
PROCEDURE
Chapter Issue 3 Jun 01 Installation Manual 7.5
PROCEDURE
Ensure MIU is configured with the correct protocols for upline and downline
machines as detailed earlier.
1. Power up the machine using the mains isolator, ensure that the air supply is
connected.
The message prompt bar displays - ‘Press SYSTEM Button To Initialize
Printer or Select Diagnostics or Load Data’.
2. Press System button, the machine initializes.
3. Select Maint. (F8).
4. Select Set Prefs,(F5).
The Set Preferences window is displayed.
5. Using the Next and Previous keys highlight the Upline Protocol function.
Use the Incr. and Decr. keys to change to the required protocol, eg. Sanyo.
6. Repeat Step 5 for the Downline Protocol. At this stage, if required, change
the Display Units, Transfer Mode etc.
Run
Open
Cover
Paste
Load
Clean
Screen
Adjust Setup Monitor Maint.
Calibrat
Pressure
Calibrat
Offset
Calibrat
Vision
House
Keeping
Set
Prefs
Diagnost
Test
Cycles
Exit
Set Preferences
TRANSPORT MODE
MACHINE UNITS
UPLINE PROTOCOL
DOWNLINE PROTOCOL
TRANSFER PERIOD
SELECTIVE PRINT/PASS
PASTE DISPENSE POS.
COMMS PROTOCOL
EVENT RECORDING
TOOLING HARDWARE
FIDUCIAL REFERENCE
PRESSURE H/W
SCREEN SIZE
CONSUMABLE ACTION
LEFT TO LEFT
Metric
NO FMI
NO FMI
20
DISABLED
FRONT
NO COMMS
GROUP 3
MAGNETIC
LEFT
FITTED
265
WARN
secs
..more
Next Previous Incr. Decr. Exit
FOREIGN MACHINE INTERFACE
PROCEDURE
7.6 Installation Manual Chapter Issue 3 Jun 01
7. When completed select Exit (F8). This saves the revised printer configura-
tion.
8. Select Setup (F6).
9. Select Mode (F1) until the mode displayed changes to No Print.
10.Select Exit (F8).
11.Ensure that the Upline and Downline Machines are connected and are
powered up, (E Stop loop connected if necessary).
12.Select Run (F1). This function key changes, to read Stop.
The screen printer requests a board from the upline machine and pass it through
the machine. The board stops at the sensor on the conveyor. On request from the
downline machine the board passes onto the external conveyor. When the sensor
is clear the screen printer requests another board from the upline machine and
the sequence repeats.
Selecting Stop ceases the sequence, changing the Stop key back to the Run key.
This shows that the interface is working between the screen printer and the
external machines.
Mode
Load
Data
Edit
data
Setup
squeegee
Change
Screen
Change
Tooling
Change
Language
Exit
Run Head
Paste
Load
Clean
screen
Adjust Setup Monitor Maint.
Mode
Load
Data
Edit
data
Setup
squeegee
Change
Screen
Change
Tooling
Change
Language
Exit
Mode
Load
Data
Edit
data
Setup
squeegee
Change
Screen
Change
Tooling
Change
Language
Exit
Run Head
Paste
Load
Clean
Screen
Adjust Setup Monitor Maint.