Hybrid Calibration Offset Measurement and Correction Operation Manual.pdf - 第12页

H ybrid Cali bration Offset M easurement and Correction Operation Manual N XT V8.95 FUJI CORPORAT ION 12/18 Notes: 1. The jig p arts are extreme ly small. Be careful n ot to drop them insid e t he mac hi ne when per f or…

100%1 / 18
Hybrid Calibration Offset Measurement and Correction Operation Manual NXT V8.95
FUJI CORPORATION 11/18
8. Troubleshooting errors that occur during hybrid calibration
measurement
The following explains how to troubleshoot errors that may occur when using the
hybrid calibration offset measurement function.
8.1. Errors when jig parts are not set on the stand
The presence of jig parts in the part pockets of the stand is checked by the mark
camera before measurement begins. An error occurs if parts cannot be detected.
For this error, because guidance is displayed to check whether jig parts are
actually set in the part pockets of the stand, the same error clearance guidance is
displayed as for when an emergency stop occurs during measurement (for an
unrelated reason such as the emergency stop button being pushed).
NXT-2 operation panel NXT-3 operation panel
1. Push the OK button (press the pull out module pictogram for the NXT-3) and pull
the module out.
2. Confirm that no jig parts remain inside the machine (such as on the stand or
the nozzle).
3. If any jig parts are found, remove them and set them in the part pockets on the
stand.
4. Push [OK] (press the step pictogram for the NXT-3) to tell the machine that
maintenance (setting the jig parts) is complete.
5. Returning the module completes the procedure for clearing the error. The
machine waits for the START button to be pushed.
6. Push the START button to start hybrid calibration measurement (regardless of
the condition before the error, measurement is performed for all holders).
Hybrid Calibration Offset Measurement and Correction Operation Manual NXT V8.95
FUJI CORPORATION 12/18
Notes:
1. The jig parts are extremely small. Be careful not to drop them inside the machine
when performing this procedure.
2. If the above procedure is not performed, clear the error using the forced error
removal function in Accessory Software. When jig parts are on the nozzle, return
the jig parts to the jig part storage pocket on the jig stand and then use the forced
error removal function. (See chapter 9 for details on this function).
8.2. Stand mark vision processing errors
When the jig parts are placed on the stand, in order to calculate the placement
position, the marks on the stand are vision processed. Also in order to determine the
exact condition of the placed jig parts, the stand marks and the placed jig part marks
are vision processed. For these errors, where there is some problem with vision
processing, guidance instructs the operator to clean the stand and the jig parts.
NXT-2 operation panel NXT-3 operation panel
1. Push the OK button (press the pull out module pictogram for the NXT-3) and pull
the module out.
2. Clean the marks on the stand (if measurements are being performed with glass
jig parts, clean these too).
3. Set the parts in the part pockets on the stand.
4. Push [OK] (press the step pictogram for the NXT-3) to tell the machine that
maintenance (setting the jig parts) is complete.
5. Returning the module completes the procedure for clearing the error. The
machine waits for the START button to be pushed.
6. Push the START button to start hybrid calibration measurement (regardless of
the condition before the error, measurement is performed for all holders).
Hybrid Calibration Offset Measurement and Correction Operation Manual NXT V8.95
FUJI CORPORATION 13/18
Notes:
1. Push the MONITOR button (camera pictogram on the NXT-3 touchscreen) to
display the vision processing images. Press MONITOR (camera pictogram on the
NXT-3 touchscreen) again to return to the guidance screen.
2. The jig parts are extremely small. Be careful not to drop them inside the machine
when performing this procedure.
3. If the above procedure is not performed, clear the error using the forced error
removal function in Accessory Software. When jig parts are on the nozzle, return
the jig parts to the jig part storage pocket on the jig stand and then use the forced
error removal function. (See chapter 9 for details on this function).
8.3. Jig part vision processing errors
When the jig parts are placed on the stand, the jig is vision processed in order to
correct for the exact position of the jig on the nozzle after pickup. For these errors,
where there is some problem with jig part vision processing, guidance instructs the
operator to clean the jig parts.
NXT-2 operation panel NXT-3 operation panel
1. Push the OK button (press the pull out module pictogram for the NXT-3) and
pull the module out.
2. Clean the jig parts.
3. Set the parts in the part pockets on the stand.
4. Push [OK] (press the step pictogram for the NXT-3) to tell the machine that
maintenance (setting the jig parts) is complete.
5. Returning the module completes the procedure for clearing the error. The
machine waits for the START button to be pushed.
6. Push the START button to start hybrid calibration measurement (regardless
of the condition before the error, measurement is performed for all holders).