3OM-1064-001 - 第257页

0103-003 4-53 Tg0248-PM-ER 5. Component Recognition Error Code and List of Error Messages Error Code Display A Display B 20630003 COMPONENT DETECTION ERROR SOME LEADS CANNOT BE DETECTED. 20630004 COMPONENT DETECTION ERRO…

100%1 / 308
Note: The second digit from the last one of the error code represents Electrical Contact 1, 2, or 3.
The third digit from the last one of the error code represents Electrical Contact Position 0,
1, 2, or 3.
0: Upper Side 1: Left Side 2: Lower Side 3: Right Side
(Cause 1) Wrong parameters (electrical contact data) are set in the component library data for the
selected component.
(Cause 2) Is there any inconsistent reflection at the electrical contact corner or edge?
(Reset Procedure in the case of Cause 1)
Reset Procedure
(1) Check the selected component and the electrical contact data in the component library data.
(2) If wrong parameters are set in the component library data, correct them.
(Reset Procedure in the case of Cause 2)
Reset Procedure
(1) In this case, change the lighting mode to “MANUAL (FRONT LIGHTING)” and perform the
recognition with much brighter light.
2042A330 ELECTRICAL CONTACT
to 339 (RIGHT) RECOGNITION ERROR
Note: A represents “2” or “3”.
CORNER (LOWER-RIGHT) OF ELECTRICAL CON-
TACT 3 IS UNABLE RECOGNITION.
2043A320 ELECTRICAL CONTACT
to 329 (RIGHT) RECOGNITION ERROR
Note: A represents “2” or “3”.
CORNER (LOWER-LEFT) OF ELECTRICAL CONTACT
3 IS UNABLE RECOGNITION.
2042A370 ELECTRICAL CONTACT
to 379 (RIGHT) RECOGNITION ERROR
Note: A represents “2” or “3”.
EDGE (LOWER-LEFT) OF ELECTRICAL CONTACT 3
IS UNABLE RECOGNITION.
2042A380 ELECTRICAL CONTACT
to 389 (RIGHT) RECOGNITION ERROR
Note: A represents “2” or “3”.
EDGE (LOWER-RIGHT) OF ELECTRICAL CONTACT 3
IS UNABLE RECOGNITION.
2042A390 ELECTRICAL CONTACT
to 399 (RIGHT) RECOGNITION ERROR
Note: A represents “2” or “3”.
EDGE (UPPER-RIGHT) OF ELECTRICAL CONTACT 3
IS UNABLE RECOGNITION.
2042A340 ELECTRICAL CONTACT
to 349 (RIGHT) RECOGNITION ERROR
Note: A represents “2” or “3”.
CORNER (UPPER-RIGHT) OF ELECTRICAL CON-
TACT 3 IS UNABLE RECOGNITION.
2042A350 ELECTRICAL CONTACT
to 359 (RIGHT) RECOGNITION ERROR
Note: A represents “2” or “3”.
INTERNAL ERROR OCCURRED DURING EDGE
RECOGNITION OF ELECTRICAL CONTACT 3.
2042A360 ELECTRICAL CONTACT
to 369 (RIGHT) RECOGNITION ERROR
Note: A represents “2” or “3”.
EDGE (UPPER-LEFT) OF ELECTRICAL CONTACT 3 IS
UNABLE RECOGNITION.
5. Component Recognition Error Code and List of Error Messages
Error Code Display A Display B
0103-001 4-52-1 Tg0248-PM-ER
0103-003 4-53 Tg0248-PM-ER
5. Component Recognition Error Code and List of Error Messages
Error Code Display A Display B
20630003 COMPONENT DETECTION
ERROR
SOME LEADS CANNOT BE DETECTED.
20630004 COMPONENT DETECTION
ERROR
UNSPECIFIED LEADS ARE DETECTED.
20630005 COMPONENT DETECTION
ERROR
LEAD POSITION WAS OUT OF TOLERANCE.
20630002 COMPONENT DETECTION
ERROR
THE DETECTED LEAD POSITION DOES NOT MATCH
THE POSITION DATA.
20630001 COMPONENT DETECTION
ERROR
COMPONENT NOT FOUND.
20630007 COMPONENT DETECTION
ERROR
RECOGNITION ABORTED BECAUSE OF IMPROPER
COMPONENT HANDLING.
20630006 COMPONENT DETECTION
ERROR
WIDTH OF LEAD EXCEEDS THE TOLERANCE.
20630009 COMPONENT DETECTION
ERROR
CONTRAST BETWEEN COMPONENT AND BACK-
GROUND IS TOO LOW.
20660002 COMPONENT DETECTION
ERROR
UNSPECIFIED LEADS ARE DETECTED.
20630008 COMPONENT DETECTION
ERROR
RECOGNITION ABORTED BECAUSE OF IMPROPER
COMPONENT HANDLING.
(Cause 1) The number of leads is not suitable.
(Cause 2) Objects shaped identically to the leads exist at both ends of the lead group.
(Cause 3) Dirt and dust have accumulated at both ends of the lead group.
(Reset Procedure in the case of Causes 1, 2 and 3)
Reset Procedure
(1) Press the [ZERO] button to return all the axes to their original positions.
(2) Re-start.
(3) If the device can’t be re-started, contact our service personnel.
0103-001 4-53-1 Tg0248-PM-ER
5. Component Recognition Error Code and List of Error Messages
Error Code Display A Display B
20660003 COMPONENT DETECTION
ERROR
SOME LEADS CANNOT BE DETECTED.
20660005 COMPONENT DETECTION
ERROR
LEAD GROUP NOT FOUND.
(Cause 1) The number of leads is not suitable.
(Cause2) The lead width is not suitable.
(Too large or small parameter is set in the "WIDTH" data box of the label "LEAD
DATA".)
(Cause 3) The leads look blurred.
(There is an extremely dark lead compared with other leads.)
(Cause 4) The direction of the component feed (direction of the component) is not suitable.
(Cause 5) Dirt, etc., have adhered to the cover glass in the fixed lighting unit.
(This can be checked through the recognition monitor.)
(Reset Procedure in the case of Causes 1, 2, 3, 4 and 5)
Reset Procedure
(1) Press the [ZERO] button to return all the axes to their original positions.
(2) Re-start.
(3) If the device can’t be re-started, contact our service personnel.
(Cause 1) No component is picked up.
(Cause 2) A different component (small component, etc.) is picked up.
(Cause 3) The lighting is not ON.
(Reset Procedure in the case of Causes 1, 2 and 3)
Reset Procedure
(1) Press the [ZERO] button to return all the axes to their original positions.
(2) Re-start.
(3) If the device can’t be re-started, contact our service personnel.