YSi-X_Ope_E - 第90页

4-29 4 Maintenance 6.1.2 Cleaning and greasing the W-axis guides n Required tools • Lent-free cleaning wipe • Specified grease (NSL) c CAUTION W ear protective glasses and gloves when handling grease. 1 Widen the conv ey…

100%1 / 124
4-28
4
Maintenance
6. Three-month inspection
n
NOTE
Before beginning work, remove the rear center panel by referring to section 3.4 “Removing the rear center panel” in
this chapter so that you can open and close the rear safety door. After finishing the work, reattach the rear center
panel.
c
CAUTION
• When handling grease or lubricant, read and follow the precautions listed in section 3.2.2, "Lubricating tools and
grease", in this chapter.
• If abnormal noise is emitted from the ball screw or guide of each axis, then contact our sales representative for
assistance. Disassembly and cleaning of the ball screw or guide by the user will void the warranty.
6.1 Cleaning and greasing the ball screws and guides
6.1.1 Cleaning and greasing the W-axis ball screws
n
Required tools
• Lent-free cleaning wipe
• Specified grease (NSL)
c
CAUTION
Wear protective glasses and gloves when handling grease.
1
Widen the conveyor width to the
maximum.
Perform return-to-origin to widen the
conveyor width to the maximum.
e
2
Press the emergency stop button.
The machine must be in emergency stop to
ensure safety during work.
3
Open the rear safety door of the
machine.
Then move the conveyor table to the rear
side.
4
Clean the W-axis ball screw.
Wipe away the old grease and dirt from the
entire ball screw with a paper wipe.
53430-M6-00
c
CAUTION
Wipe away the old grease and dirt in the lead groove
of the ball screw.
Also check that no debris or residue
remains in the lead groove.
5
Apply grease to the ball screw.
Apply the specified grease (NSL) by hand
uniformly over the entire ball screw.
53431-M6-10
6
Wipe away excess grease
.
Wipe away excess grease with a paper
wipe.
Cleaning theW-axis ball screw
Step 4
W-axis ball screw
Paper wipe
Lubricating the W-axis ball screw
Step 5
4-29
4
Maintenance
6.1.2 Cleaning and greasing the W-axis guides
n
Required tools
• Lent-free cleaning wipe
• Specified grease (NSL)
c
CAUTION
Wear protective glasses and gloves when handling grease.
1
Widen the conveyor width to the
maximum.
Perform return-to-origin to widen the
conveyor width to the maximum.
e
2
Press the emergency stop button.
The machine must be in emergency stop to
ensure safety during work.
3
Open the safety door on the rear of
the machine.
4
Clean the guides.
Wipe away the old grease and dirt from the
entire guide with a paper wipe.
53432-M6-00
c
CAUTION
Also wipe clean the slide groove of each guide.
5
Change the conveyor width.
1. Close the rear safety door of the
machine and release emergency stop.
2. Open the [Unit]-[Conveyor] tab and
press the [Width] button. When the
“Conveyor” dialog box appears, enter
“100” or so in the "Target Width" box and
press [OK].
The conveyor width will change to the
specified size.
e
6
Press the emergency stop button
again.
7
Open the rear safety door of the
machine.
8
Clean the guide.
Using a paper wipe, remove the old grease
and dirt on the guides where you could not
clean in step 4.
c
CAUTION
Also wipe clean the slide groove of each guide.
9
Apply grease the guides.
Apply the specified grease (NSL) by hand
uniformly over the entire guides.
53433-M6-10
0
Wipe away excess grease
.
Wipe away excess grease with a paper
wipe.
Cleaning the W-axis guide
Step 4
W-axis guide
Paper wipe
Lubricating the W-axis guide
Step 9
4-30
4
Maintenance
6.1.3 Cleaning and greasing the MS-axis guides
n
Required tools
• Lent-free cleaning wipe
• Grease gun
• Specified grease (NSL)
c
CAUTION
Wear protective glasses and gloves when handling grease.
e
1
Press the emergency stop button.
The machine must be in emergency stop to
ensure safety during work
.
2
Open the front safety door of the
machine.
3
Clean the guides.
Move the stopper unit back and forth by
hand and wipe away the old grease and
dirt from the entire guide with a paper wipe.
53434-M6-10
c
CAUTION
Also wipe clean the slide groove of each guide.
4
Inject new grease.
Use the grease gun to inject the specified
grease (NSL) into the grease nipple (2
place).
53435-M6-10
n
NOTE
See Chapter 5, “Lubrication points”, for details on the
lubrication points and grease gun nozzles.
5
Wipe away excess grease
.
Move the stopper unit back and forth by
hand and then wipe away excess grease
with a paper wipe.
Cleaning MS-axis guide
Step 3
MS-axis guide
Stopper unit
Paper wipe
Lubricating the MS-axis guide
Step 4
Grease nipple
Grease nipple