00198442-01_UM_TX-V2_EN - 第145页
User manual SIPLACE TX V2 3 Technical data and assemblies From software version 711.1 04/2018 3.8 SIPLACE tape feeder modules for SIPLACE TX 145 3.8.4 Energy and dat a interface (EDIF) fo r X feeder modules Item no. 0014…
3 Technical data and assemblies User manual SIPLACE TX V2
3.8 SIPLACE tape feeder modules for SIPLACE TX From software version 711.1 04/2018
144
3.8.3 Linear Dipping Unit 2 X ( LDU 2X)
Item no. 00117012-xx Linear dip module for flux / LDU 2 X
The LDU 2 X is a special feeder module, which can make flux available with a defined layer thick-
ness. This flux can be used to coat components, thereby improving their solder properties. The
LDU 2 X is set up on the changeover table in the same way as an X feeder module and is con-
trolled via the station software and line software.
For a detailed description, refer to the user guide "SIPLACE LDU 2 X".
3
Fig. 3.8 - 4 Linear Dipping Unit (LDU 2 X)
3.8.3.1 Technical data
Dimensions (L x W x H) 629 mm x 105 mm x 202 mm
Weight 11 kg
Current consumption 24 V dc bis 30 V dc, 2 A (60 W)
Max. noise emissions 61dB (A)
Temperature range (storage) Between -25°C and +55°C
Temperature range (operation) Between +18°C and +25°C
Humidity (storage) ≤ 95%
Humidity (operation) 30% - 75% (on average not > 45%)
User manual SIPLACE TX V2 3 Technical data and assemblies
From software version 711.1 04/2018 3.8 SIPLACE tape feeder modules for SIPLACE TX
145
3.8.4 Energy and data interface (EDIF) for X feeder modules
Item no. 00141247-xx Energy and data interface for X feeder modules
3
Fig. 3.8 - 5 Energy and data interface for X feeder modules
(1) Unlocking button for locking latch
(2) Operator panel
(3) Data cable
(4) Power supply cable
(5) Electronics housing
(6) Fold-out feet
(7) Omega profile for guiding feeder modules
(8) Locking latch
(9) Locating hole for front centering pin of feeder module
(10) Base plate
(11) Tape reel holder
3 Technical data and assemblies User manual SIPLACE TX V2
3.8 SIPLACE tape feeder modules for SIPLACE TX From software version 711.1 04/2018
146
3.8.4.1 Description
The energy and data interface allows X feeder modules to be used outside the placement machine
and presetup area. The interface consists of an aluminum frame with omega profile for holding
and guiding the feeder modules. As with the component trolley, the feeder module is placed on
the omega profile, with the slider guides, and is pushed forwards until the front centering pin of the
feeder module is fully inserted into the locating hole. The locking latch locks the feeder module in
this position. To remove the feeder module, simply press the release button. The locking latch is
pressed downwards and releases the feeder module. Fold-out feet stabilize the position of the en-
ergy and data interface, particularly for wider feeder modules.
The electronics housing holds the electronic control unit for the energy and data interface. The
operating panel consists of start and stop buttons and two status LEDs. Communication with a PC
takes place via the data cable. The power supply cable is connected to the power supply unit pro-
vided.
3.8.4.2 Usage
The energy and data interface is used to check, maintain and repair X feeder modules. It can also
be used for setting up in advance for PCB production. In this case, the energy and data interface
is fixed to the base plate. The tape reel holder is also mounted on the base plate. When a com-
ponent tape is inserted, you can check or reset the increment, pick-up position and conveyor
speed. The detailed user manual describes how to use the interface and the necessary servicing
work.
3.8.4.3 Scope of delivery
– Single Slot EDIF
– Power supply, 100 - 120 / 200 - 240 VAC, +30VDC, 4.3 A
– Base plate with tape reel arm
– User manual